Intermatic T101B Manual
Intermatic
bryter
T101B
Læs nedenfor 📖 manual på dansk for Intermatic T101B (1 sider) i kategorien bryter. Denne guide var nyttig for 2 personer og blev bedømt med 4.6 stjerner i gennemsnit af 1.5 brugere
Side 1/1
MODEL: T101B
24 HR. DIAL TIME SWITCH (SPST)
WITH INDEPENDENTLY WIRED CLOCK MOTOR
TYPE 1 INDOOR USE ONLY
40 A RESISTIVE, 120-480 VAC;
40 A INDUCTIVE, OR TUNGSTEN OR
1000 VA PILOT DUTY 120 VAC;-277
2 HP (24 FLA)-120 VAC; 5 HP (28 FLA) - 240 VAC.
1 VA MINIMUM AT 24 VAC
16 A ELECTRONIC BALLAST, 277 VAC
PRESSURE PLATE
TERMINAL SCREW
MAKE SURE WIRE
INSULATION CLEARS
PRESSURE PLATE
MINIMUM
COPPER
WIRE SIZE
(AWG)
MAX.
LOAD
(AMP)
MIN.
INSUL-
ATION
TEMP(°C)
75°C INSULATION MAX. MOTOR
LOAD (HP)
SINGLE PHASE
3 PHASE
120 V. 240 V. 208 V.
240 V.
14
12
10
8
15
20
30
40
90
90
90
90
1/2
1
2
-
2
2 1/2
3
5
N/A
N/A
TIME
POINTER
TIME
DIAL
OFF
TRIPPER
MANUAL
LEVER
ON
TRIPPER
CLOCK MOTOR: 120 VAC, 60 HZ.
CLOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO
ORDER REPLACEMENT, INDICATE ART NO. (WG--) ON MOTOR COVER.
CLOCK
MOTOR
EQUIPMENT
GROUND
A
1
3
4
120V
CLOCK
MOTOR
SUPPLY
TO
LOAD
GRD
WIRING DIAGRAM
SUPPLY
LR3730
UL
HOLOGRAM
LABEL
WARNING
Risk of Fire or Electric Shock
• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.
• Installation and/or wiring must be in accordance with national and local electrical code requirements.
• Use wires rated at least 90°C - COPPER conductors ONLY.
• Replace plastic insulator covering terminals before powering ON.
• KEEP DOOR CLOSED AT ALL TIMES when not servicing.
NOTICE
• Rotate timer dial clockwise only.
• Do not move the clock hands on the timer. Moving the clock hands can damage the timer.
AVERTISSEMENT
Risque d’incendie ou de choc électrique
• Utiliser des fils classés 90°C minimum - Conducteurs en CUIVRE UNIQUEMENT.
PROGRAMMING INSTRUCTIONS
1. TO SET “ON” AND “OFF” TIMES: Hold trippers against edge of CLOCK-
DIAL ON OFF, pointing to time (AM or PM) when and operations are desired,
tighten tripper screws firmly. For additional tripper pairs on CLOCK-DIAL
order 156T1978A.
2. TO SET TIME-OF-DAY: Pull CLOCK-DIAL outward. Turn in either direction
and align the exact time-of-day on the (the time now, when CLOCK-DIAL
switch is being put into operation) to the pointer. DO NOT MOVE POINTER.
OPERATING INSTRUCTIONS
•
TO OPERATE SWITCH MANUALLY: MANUAL LEVERMove
CLOCK-below
DIAL left or right as indicated by arrows. This will not effect next operation.
• IN CASE OF POWER FAILURE, reset CLOCK-DIAL to proper time-of-day.
See programming instructions.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698
154--01992
WIRING INSTRUCTIONS: Remove 1/2 inch of insulation from wire ends. Tighten terminal screws firmly
(2-18 in-lbs). Use solid or stranded COPPER only. May use two wires of the same size and type.conductors
Produkt Specifikationer
| Mærke: | Intermatic |
| Kategori: | bryter |
| Model: | T101B |
Har du brug for hjælp?
Hvis du har brug for hjælp til Intermatic T101B stil et spørgsmål nedenfor, og andre brugere vil svare dig
bryter Intermatic Manualer
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
bryter Manualer
- bryter QNAP
- bryter Lancom
- bryter DEHN
- bryter Advantech
- bryter D-Link
- bryter Televés
- bryter Vemer
- bryter Tenda
- bryter Suevia
- bryter Yamaha
- bryter Ecler
- bryter Intellinet
- bryter CyberPower
- bryter Extron
- bryter Digitus
Nyeste bryter Manualer
7 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
3 Juni 2025
2 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025