Intermatic T7401B Manual

Intermatic bryter T7401B

Læs gratis den danske manual til Intermatic T7401B (1 sider) i kategorien bryter. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Intermatic T7401B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

MINIMUM

COPPER

WIRE SIZE

(AWG)

MAX.

LOAD

(AMP)

MIN.

INSUL-

ATION

TEMP(°C)

75°C INSULATION MAX. MOTOR

LOAD (HP)

SINGLE PHASE

3 PHASE

120 V.

240 V.

208 V.

240 V.

1/2

2 1/2

7 1/2

120 V

60 HZ

LOADS

SUPPLY

WIRING DIAGRAM

GROUND

SCREW

CLOCK

MOTOR

PROGRAMMING INSTRUCTIONS

1. TO SET “ON” TIMES, place bright ON trippers against edge of CLOCK-DIAL at day-of-week and time-of-day when “ON” operations are

desired. Tighten tripper screws securely.

2. TO SET “OFF” TIMES, OFF place dark trippers against edge of CLOCK-DIAL at times when “OFF” operations are desired. Tighten trip-

per screws securely.

3. TO SKIP DAYS, omit trippers for the day(s) automatic operations is/are not required.

4. TO SET DIAL TO TIME-OF-DAY, turn dial CLOCKWISE and align the exact day-of-week and time-of-day (AM or PM) on dial with the

TIME POINTER. Some allowance may be required to compensate for gear backlash.

CAUTION: DO NOT MOVE POINTER OR FORCE DIAL COUNTERCLOCKWISE.

OPERATING INSTRUCTIONS

• TO OPERATE SWITCH MANUALLY: MANUAL LEVER Move below CLOCK-DIAL left or right as indicated by arrows. This will not affect

next automatic operation.

• IN CASE OF POWER FAILURE OR TO ADVANCE/RETARD TIME: Reset time-of- day, see step 4 of programming instructions.

For replacement parts contact Intermatic Customer Service or visit: www.intermatic.com

WIRING INSTRUCTIONS

This Time Switch can be wired to control one to four circuits simultaneously on a seven day schedule. Clock motor voltage may be other

than load voltage, but must be as specified. For terminal markings, internal wiring and contact arrangements refer to wiring diagram above.

See table for gauge selection. To make power connections Remove 1/2 inch of insulation from wire ends. Tighten terminal screws firmly

(2-18 in-lbs). Use solid or stranded COPPER only. May use two wires of the same size and type.conductors

MODEL: T7401B

SEVEN-DAY DIAL TIME SWITCH

TYPE 1 INDOOR USE ONLY - FOUR POLE SINGLE THROW

MINIMUM “ON” TIME 3-1/2 HR. UP TO 3-1/2 DAILY ON-OFF OPERATIONS

40 A RESISTIVE EACH POLE 120-480 VAC; 40 A INDUCTIVE, TUNGSTEN EACH POLE 120/208/240 OR 277 VAC;

1000 VA PILOT DUTY EACH POLE 120-277 VAC; 2 HP (24 FLA, 144 LRA) - 120 VAC; 5 HP (28 FLA, 168 LRA) -

240 VAC SINGLE PHASE; 7 1/2 HP (24 FLA, 168 LRA) - 208 VAC; 10 HP - 240 VAC THREE PHASE

16 A ELECTRONIC BALLAST, 277 VAC

WARNING

Risk of Fire or Electric Shock

• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.

• Installation and/or wiring must be in accordance with national and local electrical code requirements.

• Use wires rated at least 90°C - COPPER conductors ONLY.

• Replace plastic insulator covering terminals before powering ON.

• KEEP DOOR CLOSED AT ALL TIMES when not servicing.

NOTICE

• Rotate timer dial clockwise only.

• Do not move the clock hands on the timer. Moving the clock hands can damage the timer.

AVERTISSEMENT

Risque d’incendie ou de choc électrique

• Utiliser des ﬁls classés 90°C minimum - Conducteurs en CUIVRE UNIQUEMENT.

HOLOGRAM

LABEL

LR3730

CLOCK MOTOR: 120 VAC, 60 HZ.

INTERMATIC INCORPORATED

SPRING GROVE, ILLINOIS 60081-9698

154--02077

Produkt Specifikationer

Mærke:	Intermatic
Kategori:	bryter
Model:	T7401B

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic T7401B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

bryter Intermatic Manualer

Intermatic T7401B Manual

15 Juni 2025

Intermatic T103M Manual

10 Juni 2025

Intermatic T106R Manual

9 Juni 2025

Intermatic T1905E Manual

9 Juni 2025

Intermatic T1205R Manual

8 Juni 2025

Intermatic T174R Manual

8 Juni 2025

Intermatic T105 Manual

8 Juni 2025

Intermatic T103P Manual

7 Juni 2025

Intermatic T176 Manual

7 Juni 2025

Intermatic T171 Manual

7 Juni 2025

bryter Manualer

Nyeste bryter Manualer

ORNO OR-PRE-473 Manual

14 Juni 2025

Cudy GS1016E Manual

7 Juni 2025

Mercusys MS110CP Manual

6 Juni 2025

EXSYS EX-60325 Manual

6 Juni 2025

Atlona AT-HDR-MX1616 Manual

6 Juni 2025

Cudy GS108E Manual

3 Juni 2025

EXSYS EX-60321 Manual

2 Juni 2025

EXSYS EX-60320 Manual

1 Juni 2025

Intellinet 507776 Manual

1 Juni 2025

Intellinet 561792 Manual

1 Juni 2025