Intermatic T102P Manual

Intermatic bryter T102P

Læs gratis den danske manual til Intermatic T102P (1 sider) i kategorien bryter. Denne vejledning er vurderet som hjælpsom af 54 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 27.5 anmeldelser. Har du et spørgsmål om Intermatic T102P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

MINIMUM

COPPER

WIRE SIZE

(AWG)

MAX.

LOAD

(AMP)

MIN.

INSUL-

ATION

TEMP (°C)

75° INSULATION MAX. MOTOR

LOAD (HP)

SINGLE PHASE

120V 240V

1/2

2 1/2

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

3 PHASE

240V 240V

N/A

LR3730

WARNING

Risk of Fire or Electric Shock

• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.

• Installation and/or wiring must be in accordance with national and local electrical code requirements.

• Use wires rated at least 90°C - COPPER conductors ONLY.

• Bonding between conduit connections is not automatic and must be provided as part of the installation.

• For outdoor locations, raintight, or wet location, conduit hubs that comply with requirements of UL514B (standard

for ﬁttings for conduit and outlet boxes) are to be used.

• Replace plastic insulator covering terminals before powering ON.

• KEEP DOOR CLOSED AT ALL TIMES when not servicing.

NOTICE

• Rotate timer dial clockwise only.

• Do not move the clock hands on the timer. Moving the clock hands can damage the timer.

AVERTISSEMENT

Risque d’incendie ou de choc électrique

• Utiliser des ﬁls classés 90°C minimum - Conducteurs en CUIVRE UNIQUEMENT.

• La liaison entre les raccordements de conduits n’est pas automatique et doit être prévue dans le cadre de

l’installation.

• Pour les emplacements extérieurs, étanches à la pluie ou les emplacements mouillés, des entrées de conduit qui

sont conformes aux exigences de UL514B (norme pour les pièces de ﬁxation pour conduit et boîtes de sortie)

doivent être utilisées

HOLOGRAM

LABEL

PROGRAMMING INSTRUCTIONS

1. TO SET “ON” AND “OFF” TIMES: Hold trippers against edge of CLOCK-

DIAL ON OFF, pointing to time (AM or PM) when and operations are desired,

tighten tripper screws firmly. For additional tripper pairs on order CLOCK-DIAL

156T1978A.

2. TO SET TIME-OF-DAY: Pull CLOCK-DIAL outward. Turn in either direction and

align the exact time-of-day on the (the time now, when switch is CLOCK-DIAL

being put into operation) to the pointer. DO NOT MOVE POINTER.

OPERATING INSTRUCTIONS

•

TO OPERATE SWITCH MANUALLY: MANUAL LEVERMove

CLOCK-DIAL below

left or right as indicated by arrows. This will not effect next operation.

• IN CASE OF POWER FAILURE, reset CLOCK-DIAL to proper time-of-day. See

programming instructions.

INTERMATIC INCORPORATED

SPRING GROVE, ILLINOIS 60081-9698

154--02043

WIRING INSTRUCTIONS: Remove 1/2 inch of insulation from wire ends. Tighten terminal screws firmly

(2-18 in-lbs). Use solid or stranded COPPER only. May use two wires of the same size and type.conductors

MODEL: T102P

24 HOUR DIAL TIME SWITCH (SPST)

TYPE 3R RAINPROOF ENCLOSURE

SUITABLE FOR POOL EQUIPMENT CONTROL IF

INSTALLED 5 FT. OR MORE FROM EDGE OF POOL.

40 A RESISTIVE, INDUCTIVE, TUNGSTEN

OR 1000 VA PILOT DUTY 120 - 277 VAC;

2 HP (24 FLA) - 120 VAC; 5 HP (28 FLA) - 240 VAC

16 A ELECTRONIC BALLAST, 277 VAC

CLOCK MOTOR: 208 - 277 VAC, 60 HZ.

CLOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO ORDER

REPLACEMENT, INDICATE PART NO. (WG--) ON MOTOR COVER.

TIME

POINTER

TIME

DIAL

OFF

TRIPPER

MANUAL

LEVER

TRIPPER

CLOCK

MOTOR

WIRING

DIAGRAM

208

THRU

277V

SUPPLY

LOADS

GROUND

LINE 2

LINE 1

GR.

FOR 208 OR 240 V SUPPLY CONNECT

LINE 1 TO TERMINAL “A”

Produkt Specifikationer

Mærke:	Intermatic
Kategori:	bryter
Model:	T102P

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic T102P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

bryter Intermatic Manualer

Intermatic T1871BR Manual

29 Juli 2025

Intermatic T1471BR Manual

29 Juli 2025

Intermatic T106M Manual

29 Juli 2025

Intermatic T1471BCR Manual

29 Juli 2025

Intermatic T1976 Manual

29 Juli 2025

Intermatic DTAV40Q Manual

19 Juli 2025

Intermatic T7401B Manual

15 Juni 2025

Intermatic T103M Manual

10 Juni 2025

Intermatic T106R Manual

9 Juni 2025

Intermatic T1905E Manual

9 Juni 2025

bryter Manualer

Nyeste bryter Manualer

TP-Link Omada DS106GPP Manual

19 Oktober 2025

Draytek VigorSwitch PQ2200xb Manual

17 Oktober 2025

Kramer VS-88H2 Manual

16 Oktober 2025

Lancom GS-3126X Manual

16 Oktober 2025

Lancom GS-2310 Manual

16 Oktober 2025

Lancom GS-3628X Manual

16 Oktober 2025

Lancom GS-3528 Manual

16 Oktober 2025

Eberle ZTM 2 Manual

15 Oktober 2025

Manhattan 154390 Manual

7 Oktober 2025

Draytek VigorSwitch P2121 Manual

6 Oktober 2025