Intermatic T171CR Manual

Intermatic bryter T171CR

Læs gratis den danske manual til Intermatic T171CR (1 sider) i kategorien bryter. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Intermatic T171CR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

CLOCK MOTOR: 120 VAC, 60 HZ.

CLOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO

ORDER REPLACEMENT, INDICATE PART NO. (WG--) ON MOTOR COVER.

LINE

NEUT.

CLOCK

MOTOR

GROUND

GRD.

120V

SUPPLY

LOAD

WIRING

DIAGRAM

NOTICE

• Rotate timer dial clockwise only.

• Do not move the clock hands on the timer. Moving the clock hands can damage the timer.

INTERMATIC INCORPORATED

SPRING GROVE, ILLINOIS 60081-9698

154--02063

HOLOGRAM

LABEL

LR3730

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

MINIMUM

COPPER

WIRE SIZE

(AWG)

MAX.

LOAD

(AMP)

MIN.

INSUL-

ATION

TEMP(°C)

75°C INSULATION MAX. MOTOR

LOAD (HP)

SINGLE PHASE

3 PHASE

120 V. 240 V. 208 V.

240 V.

1/2

2 1/2

N/A

WIRING INSTRUCTIONS: Remove 1/2 inch of insulation from wire ends. Tighten terminal screws firmly

(2-18 in-lbs). Use solid or stranded COPPER only. May use two wires of the same size and type.conductors

PROGRAMMING INSTRUCTIONS

1. TO SET “ON” AND “OFF” TIMES: Hold trippers against edge of CLOCK-DIAL, pointing to time (AM or PM) when ON

and OFF operations are desired, tighten tripper screws firmly. For additional tripper pairs on CLOCK-DIAL order

156T1948A.

2. TO SET TIME-OF-DAY: Pull CLOCK-DIAL outward. Turn in either direction and align the exact time-of-day on the

CLOCK-DIAL (the time now, when switch is being put into operation) to the pointer. DO NOT MOVE POINTER.

3. TO SKIP OPERATION(S) ON SELECTED DAY(S): Insert SKIPPING SCREW(S) in SKIPPER WHEEL for day(s) automatic

operation(s) is/are NOT required. Tighten screws firmly. Move MANUAL LEVER to “OFF” and rotate SKIPPER WHEEL to

locate correct day-of-week opposite DAY ARROW--”YESTERDAY” if ON/CUTOUT TRIPPER has not yet advanced wheel

“TODAY” if it has.

OPERATING INSTRUCTIONS

• TO OPERATE SWITCH MANUALLY: Move MANUAL LEVER below CLOCK-DIAL left or right as indicated by arrows. This

will not effect next operation.

CAUTION: TO AVOID SLOW SWITCH ACTION FAILURE, DO NOT OPERATE

SWITCH MANUALLY NOR PLACE A TRIPPER 4 HOURS PRIOR TO

ON/CUTOUT TRIPPER SWITCHING.

• IN CASE OF POWER FAILURE, reset CLOCK-DIAL to proper time-of-day. See programming instructions.

DAY

ARROW

TIME

POINTER

TIME

DIAL

OFF

TRIPPER

MANUAL

LEVER

ON/CUTOUT

TRIPPER

SKIPPER

WHEEL

SKIPPING

SCREW

MODEL: T171CR

24 HOUR DIAL TIME SWITCH WITH “SKIPPER

’’

AND SPRING-WOUND CARRY-OVER MOTOR,

SINGLE POLE SINGLE THROW

TYPE 3R RAINPROOF ENCLOSURE

SUITABLE FOR POOL EQUIPMENT CONTROL IF INSTALLED

5 FT. OR MORE FROM EDGE OF POOL.

40 A RESISTIVE, INDUCTIVE, TUNGSTEN OR 1000 VA PILOT DUTY

120/208/240 VAC; 2 HP (24 FLA) - 120 VAC; 5 HP (28 FLA) - 240 VAC

16 A ELECTRONIC BALLAST, 277 VAC

WARNING

Risk of Fire or Electric Shock

• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.

• Installation and/or wiring must be in accordance with national and local electrical code requirements.

• Use wires rated at least 90°C - COPPER conductors ONLY.

• For outdoor locations, raintight, or wet location, conduit hubs that comply with requirements of UL514B (standard

for ﬁttings for conduit and outlet boxes) are to be used.

• Replace plastic insulator covering terminals before powering ON.

• KEEP DOOR CLOSED AT ALL TIMES when not servicing.

AVERTISSEMENT

Risque d’incendie ou de choc électrique

• Utiliser des ﬁls classés 90°C minimum - Conducteurs en CUIVRE UNIQUEMENT.

• Pour les emplacements extérieurs, étanches à la pluie ou les emplacements mouillés, des entrées de conduit qui

sont conformes aux exigences de UL514B (norme pour les pièces de ﬁxation pour conduit et boîtes de sortie)

doivent être utilisées

Produkt Specifikationer

Mærke:	Intermatic
Kategori:	bryter
Model:	T171CR

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic T171CR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

bryter Intermatic Manualer

Intermatic DTAV40Q Manual

19 Juli 2025

Intermatic T7401B Manual

15 Juni 2025

Intermatic T103M Manual

10 Juni 2025

Intermatic T106R Manual

9 Juni 2025

Intermatic T1905E Manual

9 Juni 2025

Intermatic T1205R Manual

8 Juni 2025

Intermatic T174R Manual

8 Juni 2025

Intermatic T105 Manual

8 Juni 2025

Intermatic T103P Manual

7 Juni 2025

Intermatic T176 Manual

7 Juni 2025

bryter Manualer

Nyeste bryter Manualer

Hager EGN100AU Manual

23 Juli 2025

Kramer KIT-400 Manual

23 Juli 2025

D-Link DGS-1100-26 Manual

23 Juli 2025

Hager FB22LE Manual

22 Juli 2025

CYP EL-31C-4K22 Manual

22 Juli 2025

Gira 0392112 Manual

22 Juli 2025

CYP SY-UHDVGA-4K22 Manual

22 Juli 2025

CYP EL-6010-4K22 Manual

22 Juli 2025

Hager EE856 Manual

22 Juli 2025

Nedis ZBGDN10RD Manual

22 Juli 2025