Intermatic T174CR Manual

Intermatic bryter T174CR

Læs gratis den danske manual til Intermatic T174CR (1 sider) i kategorien bryter. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Intermatic T174CR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

MODEL: T174CR

24 HOUR DIAL TIME SWITCH WITH “SKIPPER

’’

AND SPRING-WOUND CARRY-OVER MOTOR,

DOUBLE POLE SINGLE THROW (DPST)

TYPE 3R RAINPROOF ENCLOSURE

SUITABLE FOR POOL EQUIPMENT CONTROL IF INSTALLED 5 FT. OR MORE

FROM EDGE OF POOL. 40 A RESISTIVE, PER POLE 120-480 VAC, 40 A INDUCTIVE, OR

TUNGSTEN OR 1000 VA PILOT DUTY PER POLE 120-277 VAC; 2 HP (24 FLA) - 120 VAC;

5 HP (28 FLA) - 240 VAC 16 A ELECTRONIC BALLAST, 277 VAC;

HOLOGRAM

LABEL

LR3730

INTERMATIC INCORPORATED

SPRING GROVE, ILLINOIS 60081-9698

154--02071

PROGRAMMING INSTRUCTIONS

1. TO SET “ON” AND “OFF” TIMES: Hold trippers against edge of CLOCK-DIAL, pointing to time (AM or PM) when ON

and OFF operations are desired, tighten tripper screws firmly. For additional tripper pairs on CLOCK-DIAL order

156T1948A.

2. TO SET TIME-OF-DAY: Pull CLOCK-DIAL outward. Turn in either direction and align the exact time-of-day on the

CLOCK-DIAL (the time now, when switch is being put into operation) to the pointer. DO NOT MOVE POINTER.

3. TO SKIP OPERATION(S) ON SELECTED DAY(S): Insert SKIPPING SCREW(S) in SKIPPER WHEEL for day(s) automatic

operation(s) is/are NOT required. Tighten screws firmly. Move MANUAL LEVER to “OFF” and rotate SKIPPER WHEEL to

locate correct day-of-week opposite DAY ARROW--”YESTERDAY” if ON/CUTOUT TRIPPER has not yet advanced wheel

“TODAY” if it has.

OPERATING INSTRUCTIONS

• TO OPERATE SWITCH MANUALLY: Move MANUAL LEVER below CLOCK-DIAL left or right as indicated by arrows. This

will not effect next operation.

CAUTION: TO AVOID SLOW SWITCH ACTION FAILURE, DO NOT OPERATE

SWITCH MANUALLY NOR PLACE A TRIPPER 4 HOURS PRIOR TO

ON/CUTOUT TRIPPER SWITCHING.

• IN CASE OF POWER FAILURE, reset CLOCK-DIAL to proper time-of-day. See programming instructions.

DAY

ARROW

TIME

POINTER

TIME

DIAL

OFF

TRIPPER

MANUAL

LEVER

ON/CUTOUT

TRIPPER

SKIPPER

WHEEL

SKIPPING

SCREW

CLOCK MOTOR: 208-277 VAC, 60 HZ.

CLOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO ORDER

REPLACEMENT, INDICATE PART NO. (WG--) ON MOTOR COVER.

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

MINIMUM

COPPER

WIRE SIZE

(AWG)

MAX.

LOAD

(AMP)

MIN.

INSUL-

ATION

TEMP(°C)

75°C INSULATION MAX. MOTOR

LOAD (HP)

SINGLE PHASE

3 PHASE

120 V. 240 V. 208 V.

240 V.

1/2

2 1/2

N/A

WIRING INSTRUCTIONS: Remove 1/2 inch of insulation from wire ends. Tighten terminal screws firmly

(2-18 in-lbs). Use solid or stranded COPPER only. May use two wires of the same size and type.conductors

NOTICE

• Rotate timer dial clockwise only.

• Do not move the clock hands on the timer. Moving the clock hands can damage the timer.

WARNING

Risk of Fire or Electric Shock

• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.

• Installation and/or wiring must be in accordance with national and local electrical code requirements.

• Use wires rated at least 90°C - COPPER conductors ONLY.

• For outdoor locations, raintight, or wet location, conduit hubs that comply with requirements of UL514B (standard

for ﬁttings for conduit and outlet boxes) are to be used.

• Replace plastic insulator covering terminals before powering ON.

• KEEP DOOR CLOSED AT ALL TIMES when not servicing.

AVERTISSEMENT

Risque d’incendie ou de choc électrique

• Utiliser des ﬁls classés 90°C minimum - Conducteurs en CUIVRE UNIQUEMENT.

• Pour les emplacements extérieurs, étanches à la pluie ou les emplacements mouillés, des entrées de conduit qui

sont conformes aux exigences de UL514B (norme pour les pièces de ﬁxation pour conduit et boîtes de sortie)

doivent être utilisées

CLOCK

MOTOR

277/480 VOLT CONNECT MOTOR LEADS TO TERMINALS “A”

AND 1 AND SUPPLY NEUTRAL TO TERMINAL “A”.

LOAD(S)

LINE 2

WIRING DIAGRAM

240V 2 WIRE

AND GROUND

LINE 1

240V

SUPPLY

GROUND

Produkt Specifikationer

Mærke:	Intermatic
Kategori:	bryter
Model:	T174CR

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic T174CR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

bryter Intermatic Manualer

Intermatic T1871BR Manual

29 Juli 2025

Intermatic T1471BR Manual

29 Juli 2025

Intermatic T106M Manual

29 Juli 2025

Intermatic T1471BCR Manual

29 Juli 2025

Intermatic T1976 Manual

29 Juli 2025

Intermatic DTAV40Q Manual

19 Juli 2025

Intermatic T7401B Manual

15 Juni 2025

Intermatic T103M Manual

10 Juni 2025

Intermatic T106R Manual

9 Juni 2025

Intermatic T1905E Manual

9 Juni 2025

bryter Manualer

Nyeste bryter Manualer

Legrand TSDL153P Manual

10 December 2025

Legrand TSD703PTUI Manual

9 December 2025

Legrand TSDSSL7AP Manual

9 December 2025

Legrand TSD4FBL3PW Manual

9 December 2025

Lanberg DSP1-1008 Manual

4 December 2025

Lanberg DSP1-1005 Manual

4 December 2025

Lanberg DSP2-1005-12V Manual

2 December 2025

Praxis PPL 1602 Manual

2 December 2025

Lanberg RSFE-24P-2C-360 Manual

2 December 2025

Roline 21.13.1173 Manual

2 December 2025