Intermatic T1975E Manual

Intermatic bryter T1975E

Læs gratis den danske manual til Intermatic T1975E (1 sider) i kategorien bryter. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Intermatic T1975E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

MODEL: T1975E

PROGRAM TIME SWITCH WITH “SKIPPER

”

FOR UP TO 48 TIMING OPERATIONS

ON 24 HOUR SCHEDULE

SINGLE POLE DOUBLE THROW

SWITCH RATING: 20 AMP. 125-480 VOLTS A.C. 1/2 HP-125V 1 HP-250V.

WIRING INSTRUCTIONS

This Time Switch can be wired to control two circuits as Single Pole

Double throw, or to control one circuit as Single Pole Single Throw.

Either normally open (NO) or normally closed (NC). To wire switch see

wiring diagram above.

TO PROGRAM TIME SWITCH, Depress tripper(s) into dial at

desired time(s) operation(s) is/are required.

• ON TIME: First tripper turns on the load for 16-20 minutes. Each

additional tripper will lengthen the on time by 15 minutes.

• OFF TIME: First tripper in raised position turns off the load for

10-14 minutes.Each additional space will lengthen the of time by 15

minutes.

SET TIME-OF-DAY: Turn dial in clockwise direction only and align

the exact time-of-day (the time now when switch is being put into

operation) to the “TIME” arrow on insulator.

CHECK SKIPPER WHEEL. If switch is to function seven days

a week pull all pins, in skipper wheel up to “OUT” position.

Otherwise depress pin(s) in skipper wheel for day(s) automatic

operation is not required.

• If, after the dial is set to the correct time of day and the skipper

tripper (silver color) has not yet passed the skipper wheel, turn

wheel counter clockwise so that the previous day is opposite the

“DAY” arrow.

• If the skipper tripper has already passed the skipper wheel set the

correct day opposite the “DAY” arrow.

TIME

DIAL

INSULATOR

MANUAL

LEVER

CAP

NUTS

CLOCK

MOTOR

SUPPLY

NORMALLY CLOSED CIRCUIT

NORMALLY OPEN CIRCUIT

FIG. 1 WIRING DIAGRAM

CLOCK

COM.

N.C.

N.O.

N.C.

LOAD

NO.

LOAD

OPERATING INSTRUCTIONS

TO CONTROL LOADS MANUALLY, Move manual lever (See Figure 1)

up. This lever will close normally open circuit and open the normally

closed circuit. To return, to automatic control, move lever back to its

original position .

IN CASE OF POWER FAILURE, reset dial. See step (2) of programming

instructions.

INTERMATIC INCORPORATED

LIBERTYVILLE, ILLINOIS 60048

154--03516

CLOCK MOTOR: 480 VOLTS - 60 HZ.

CLOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO ORDER

REPLACEMENT, INDICATE PART NO. (WG--) ON MOTOR COVER.

LR3730

SKIPPER

WHEEL

Produkt Specifikationer

Mærke:	Intermatic
Kategori:	bryter
Model:	T1975E

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic T1975E stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

bryter Intermatic Manualer

Intermatic DTAV40Q Manual

19 Juli 2025

Intermatic T7401B Manual

15 Juni 2025

Intermatic T103M Manual

10 Juni 2025

Intermatic T106R Manual

9 Juni 2025

Intermatic T1905E Manual

9 Juni 2025

Intermatic T1205R Manual

8 Juni 2025

Intermatic T174R Manual

8 Juni 2025

Intermatic T105 Manual

8 Juni 2025

Intermatic T103P Manual

7 Juni 2025

Intermatic T176 Manual

7 Juni 2025

bryter Manualer

Nyeste bryter Manualer

Hager EGN100AU Manual

23 Juli 2025

Kramer KIT-400 Manual

23 Juli 2025

D-Link DGS-1100-26 Manual

23 Juli 2025

Hager FB22LE Manual

22 Juli 2025

CYP EL-31C-4K22 Manual

22 Juli 2025

Gira 0392112 Manual

22 Juli 2025

CYP SY-UHDVGA-4K22 Manual

22 Juli 2025

CYP EL-6010-4K22 Manual

22 Juli 2025

Hager EE856 Manual

22 Juli 2025

Nedis ZBGDN10RD Manual

22 Juli 2025