Intermatic T7802B Manual

Intermatic bryter T7802B

Læs gratis den danske manual til Intermatic T7802B (1 sider) i kategorien bryter. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Intermatic T7802B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

MINIMUM

COPPER

WIRE SIZE

(AWG)

MAX.

LOAD

(AMP)

MIN.

INSUL-

ATION

TEMP(°C)

75°C INSULATION MAX. MOTOR

LOAD (HP)

SINGLE PHASE

3 PHASE

120 V.

240 V.

208 V.

240 V.

1/2

2 1/2

N/A

PROGRAMMING INSTRUCTIONS

1. TO SET “ON” TIMES, place bright ON trippers against edge of CLOCK-DIAL at day-of-week and time-of-day when “ON” operations are

desired. Tighten tripper screws securely.

2. TO SET “OFF” TIMES, OFF place dark trippers against edge of CLOCK-DIAL at times when “OFF” operations are desired. Tighten trip-

per screws securely.

3. TO SKIP DAYS, omit trippers for the day(s) automatic operations is/are not required.

4. TO SET DIAL TO TIME-OF-DAY, turn dial CLOCKWISE and align the exact day-of-week and time-of-day (AM or PM) on dial with the

TIME POINTER. Some allowance may be required to compensate for gear backlash.

CAUTION: DO NOT MOVE POINTER OR FORCE DIAL COUNTERCLOCKWISE.

OPERATING INSTRUCTIONS

• TO OPERATE SWITCH MANUALLY: MANUAL LEVER Move below CLOCK-DIAL left or right as indicated by arrows. This will not affect

next automatic operation.

• IN CASE OF POWER FAILURE OR TO ADVANCE/RETARD TIME: Reset time-of- day, see step 4 of programming instructions.

For replacement parts contact Intermatic Customer Service or visit: www.intermatic.com

MODEL: T7802B

SEVEN-DAY DIAL TIME SWITCH

TYPE 1 INDOOR USE ONLY - FOUR POLE; TWO NORMALLY OPEN-TWO NORMALLY CLOSED

MINIMUM “ON” TIME 3-1/2 HR. UP TO 3-1/2 DAILY ON-OFF OPERATIONS

40 A RESISTIVE EACH POLE 120-480 VAC; 40 A INDUCTIVE, TUNGSTEN EACH POLE 120/208/240 OR 277 VAC;

1000 VA PILOT DUTY EACH POLE 120-277 VAC; 2 HP (24 FLA, 144 LRA) - 120 VAC; 5 HP (28 FLA, 168 LRA) -240 VAC

16 A ELECTRONIC BALLAST, 277 VAC

WARNING

Risk of Fire or Electric Shock

• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.

• Installation and/or wiring must be in accordance with national and local electrical code requirements.

• Use wires rated at least 90°C - COPPER conductors ONLY.

• Replace plastic insulator covering terminals before powering ON.

• KEEP DOOR CLOSED AT ALL TIMES when not servicing.

NOTICE

• Rotate timer dial clockwise only.

• Do not move the clock hands on the timer. Moving the clock hands can damage the timer.

AVERTISSEMENT

Risque d’incendie ou de choc électrique

• Utiliser des ﬁls classés 90°C minimum - Conducteurs en CUIVRE UNIQUEMENT.

HOLOGRAM

LABEL

LR3730

CLOCK MOTOR: 208-277 VAC, 60 HZ.

INTERMATIC INCORPORATED

SPRING GROVE, ILLINOIS 60081-9698

154--02090

208

277 V

60 HZ

LOADS

SUPPLY

WIRING DIAGRAM

GROUND

SCREW

CLOCK

MOTOR

WIRING INSTRUCTIONS

This Time Switch can be wired to control one to four circuits simultaneously on a seven day schedule. Clock motor voltage may be other than load

voltage, but must be as specified. For terminal markings, internal wiring and contact arrangements refer to wiring diagram above. To form the common

poles of a DOUBLE POLE DOUBLE THROW switch, if required, install jumpers (extend supply wires) between terminals 1-6 and 3-8. See table for gauge

selection. To make power connections Remove 1/2 inch of insulation from wire ends. Tighten terminal screws firmly (2-18 in-lbs). Use solid or stranded

COPPER conductors only. May use two wires of the same size and type.