Jablotron JA-65 MAESTRO Manual

Jablotron Sikkerhed JA-65 MAESTRO

Læs gratis den danske manual til Jablotron JA-65 MAESTRO (6 sider) i kategorien Sikkerhed. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Jablotron JA-65 MAESTRO, eller vil du spørge andre brugere om produktet?

Side 1/6
User instructions of JA-65 "Maestro" 1/6 MFM51308
User instructions of JA-65 „Maestro“
1. Indicators
Alarm alarm triggered by an intruder, smoke, gas etc.
Tamper opened cover, damaged detector, excessive number of attempts to enter code etc.
Fault power loss, lost communication with a detector etc., (confirm pressing key N)
Battery battery of the device specified on the display is low. See battery replacement section.
wireless communication in progress or information received from a wireless item
Armed continues = armed, slow blinking = exit delay, fast blinking = entrance delay
Power continues = AC power & back up battery are O.K., blinking = failure (AC power or back up battery), off = control panel
is not powered
Two digits display
Specifies event source or mode of the control panel.
event sources:
1 to16 zone input number (when is lit simultaneously the event was triggered by a corresponding wireless detector)
c1 to c8 wireless controller or keypad number ( is lit simultaneously)
C control panel
A wireless siren
J sub system (other JA-60 or 65 system enrolled)
L telephone line
d digital line (PC interface, keypad JA-60E, …)
F wireless communication of the keypad lost (JA-60F only)
control panel modes:
P programming mode
U user mode (bypass setting, testing, battery replacement, voice dialer setting)
H home (partial) arming (inputs & wireless detectors addressed to B section are bypassed)
section A arming (split system)
section B arming (split system)
arming of the complete system
a zone is bypassed when arming
waiting for more data to complete entry
2. Access codes
The control panel can be operated with the following codes (by JA-60E or JA-60F keypad or via connected PC):
Master code is an extra user code, which can be used for arming, disarming but also for code changes, entering of user mode,
bypass setting, system testing, battery replacement voice dialer programming (if enabled by installer) - factory default
Master code is 1234.
If the system is split, the use of MC will arm all sections if no section is armed or it will disarm all sections if any is
armed. If no code arming is disabled and the system is spilt then entering F1 MC will effect only section A and
entering F2 MC will effect only section B.
User codes up to 14 different user codes can be set in the system for different users for arming and disarming only (all are blank
from the factory). This way it is possible to differ between different users operations (details about used codes are
stored in the control panel internal events memory, the Comlink software or the monitoring station can access these
details).
Service code is a code for installer to open programming mode for the control panel setting and testing (entering F 0 Service code).
Note: After 5 attempts to enter an invalid code a tamper alarm is triggered, indicated by LED “Tamper” and “C” on the display.
3. Controlling the system
Arming enter your access code or press the A button on the remote control. System will beep and will start exit delay count
down. You must leave the protected area during the exit delay.
Disarming enter your access code or press the B button on the remote control. The panel will beep twice and will disarm. When
you enter the protected area before disarming, the entrance delay count down will start. If disarming is confirmed
with three beeps, check the keypad indicators for information (alarm memory, failure, low battery etc.).
To stop alarm enter your access code or press the B button on the remote control.
Panic alarm pressing or entering F 7 before your code will trigger a silent panic alarm. This can also be triggered by the
RC-22 panic button or by pressing and holding of both buttons of the RC-11 remote control for 3 seconds.
Optional user functions (following functions can be enabled or disabled in the programming mode):
arming without a code - disarming is only possible with an access code (entry of F1 can be used on JA-60D keypad for this
function). If the system is split, then this button can be used for arming of section A.
partial (home) arming - detectors addressed to B section will be ignored (except Smoke & Gas detectors). On the JA-60D
keypad code F2 can be used for partial arming. If the system is split, then this button can be used for arming of section B. If the
control panel was not programmed for partial arming or was not split, this button has no function.
door opening - will release electric door lock if connected to the system (PgX or PgY outputs). On the JA-60D keypad, code F3
can be used for this function.
panic alarm - if you are under duress, press this button before your code, this will trigger a silent alarm; if the system is armed, it
will also disarm. On the JA-60D keypad, code F7 can be used before your code to trigger a panic alarm.
F 4 memory reading - indicators and LED display will show where and what happened, press key 4 multiple times to go deeper into
the memory. Complete events list including date & time can be viewed using PC with Comlink SW.
F 5 new Master Code - after F 5 the current master code must be entered followed by the new one twice.
Example: to change Master code from 1234 to 2738 enter: F5 1234 2738 2738
F 6 new User Code - after F 6 the valid master code must be entered, number of the new user code (01 to 14) and then the new
user code. To erase any User code completely, set it to 0000
Example: user code number 5 can be entered for combination 6789 while Master code is 2738 entering: F 6 2738 05 6789.
F 9 voice message listening - to check the message(s) of the telephone dialer (control panel built in speaker will play all the
recorded messages once).
F 0 user (programming) mode - entering F 0 Master Code will be confirmed by „U“ on the LED display. The control panel is now in
the user mode for bypass setting, system testing, battery replacement, voice dialer programming (if enabled by installer).
Entering F 0 Service Code is used by the installer to enter the programming mode.
N exit - not completed function code, memory reading, user mode etc.
Note: While in the programming mode, you can select that functions , , , F4 and F9 can be used only when followed by a code (Master
or User). Acoustic indications and other features of the system can also be customized in the programming mode. Wireless keypad JA-60D can have its
own master code and one user code. Both JA-60D codes can be different than the control panel codes.
4. Zone bypassing
By using the master code, zone inputs and wireless detectors can be bypassed within a selected area of the house.
Bypass setting:
1. open User mode entering F 0 Master Code - will be confirmed by „U“ on the LED display
2. press 1 to enter the bypass menu
3. keys 1 or 7 scroll all hard wire zone inputs and all wireless (differed with indicator) detectors
4. select the input zone or wireless detector to be bypassed
5. press key 2 and hold it for two seconds to set one arming period bypass of the selected zone (battery indicator will start
flashing to confirm the bypass). If you press 2 again, this bypass will be switched off etc. (on - off - on,...). similar way with key
3 for a permanent bypass of the zone (confirmed with continuous lighting of the battery indicator). If you press 3 again, this
bypass will be switched off etc. (on - off - on,...).
6. repeating the steps 3-5 you can set up and check requested bypasses
7. to cancel all selected bypasses press and hold key 4 while in the bypass menu
8. to exit the bypass menu press N, to exit user mode press N again
Arming of the system while a zone is bypassed is confirmed with four beeps and "b" will be indicated on the keypad during the exit
delay period.
Notes:
Be sure to cancel a permanent bypass after there is no need for the bypass.
If one arming period bypass was selected for a zone, this bypass is automatically canceled after the system is armed and then disarmed. This
remains valid for arming and disarming even if the system is split into two sections.
All bypasses will be canceled after a factory default reset or after the main board’s power is disconnected.
Information about arming and bypassing is stored in system’s memory as a partial arming.
The bypass menu is only available in the user mode.
5. Voice dialer programming by user
If the control panel is equipped with a 65X telephone dialer module and if enabled in the programming mode during installation, setting
of the voice and Pager dialer telephone numbers and messages can be changed in the user mode (with master code). Setting can be
performed by entering programming sequences from the keypad (JA-60E or JA-60F) while in the control panel user mode:
Enter the user mode (entering F 0 Master Code, factory default UC=1234), indicated by a „U“ on the display. This can only be done
while the panel is disarmed.
The parameters of the dialer can be set by entering programming sequences from the keypad. Any unfinished programming
sequence can be terminated by pressing the N key.
To exit the user mode, press the N key („U“ will turn off).
User instructions of JA-65 "Maestro" 2/6 MFM51308


Produkt Specifikationer

Mærke: Jablotron
Kategori: Sikkerhed
Model: JA-65 MAESTRO

Har du brug for hjælp?

Hvis du har brug for hjælp til Jablotron JA-65 MAESTRO stil et spørgsmål nedenfor, og andre brugere vil svare dig