Joblotron JA-60M Manual

Joblotron Overvågningskamera JA-60M

Læs gratis den danske manual til Joblotron JA-60M (1 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Joblotron JA-60M, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

JA-60M wireless magnetic door detector 2 / 2 MDW51005

JA-60M Wireless Magnetic Door Detector

JA-60M Magnetic door detector is equipped with a magnet. A movement

of the magnet triggers the internal sensor in the detector. It can trigger an

Instant or Delayed intruder alarm and it also has built in tamper sensors.

There are inputs for external sensors available.

The JA-60M uses a sophisticated radio communication protocol with a

high level of data safety. The detector makes regular auto testing and

reports its conditions regularly to the system for full supervision. An

automatic testing mode makes testing an ease.

Specifications

power 3 V - 2 x AAA battery 1.5V

battery life time about 1 year

working range max. 100 m (open area)

built in sensor magnetic reed contact

external sensor inputs INP & TAMP (balanced loops)

complies with EN 50131-1 class 2

working environment indoor use , -10 to +40°C

Contents of the set: detector, magnet, 4 screws, 2 AAA batteries

Installation

To detect the opening or closing of a door or window the detector is

equipped with a magnet. Movement of the magnet triggers the internal

sensor in the detector.

• Open the detector cover by pressing the internal tab.

• Attach the detector to the wall or the frame of the door or window using

the 2 provided screws.

• Be sure that the antenna is vertical (pointing up or down).

• Attach the magnet with the provided screws to the moving part of the

door or window, and put on its cover. The gap between the detector and

magnet should not be wider than 5mm when the door is closed.

• Warning: neither the detector nor the magnet should be fixed directly to

a metal surface. If there is no other choice, an insulating pad (plastic,

wood etc.) 5mm thick or more should be used under the detector and

the magnet.

• Use DIP switch no. 1 to select if the reaction of the system to the door

opening should be instant (position ON) or delayed (position 1).

• If you do not use input terminals (TAMP & INP) they must be

connected to the GND terminal with short connecting loops and DIP

switch no. 2 must stay in the OFF position.

• Leave the JA-60M detector uncovered and without batteries installed.

Use of external sensors with JA-60M

The JA-60M detector can be used to connect external detectors which

have contacts on their outputs. For example it can be used to protect multiple

doors or windows. The built in magnetic sensor of the JA-60M can also be

disabled (DIP switch number 2 to position ON) and then the JA-60M works

only as an interface for external sensors. Two input loops (TAMP & INP

terminals) are activated when disconnected from the GND terminal.

INP – when this input is triggered (disconnected from GND), the JA-60M will

send the same information as if the built in magnetic sensor is triggered. Re-

action of the system can be selected with DIP switch number 1 (ON= instant

or 1= delayed).

TAMP – when this input is triggered (disconnected from GND), the unit will

send the same information as if the built in tamper sensor is triggered.

Balanced loops – the inputs INP & TAMP can also be used as balanced

loop inputs for higher security of connected cables. If you install an End Of

Line resistor 10k in the end of the loop (INP or TAMP), the JA-60M

automatically recognizes this situation and from this moment it will react to a

change of the resistivity (changes ±30% or more will trigger the input).

SA-200

TAMP

INP

GND

JA-60M

E.O.L. resistor

can be used

INP

GND

TAMP

delay

instant

disabledenabled

10K

Enrollment of the detector to the system

Study the installation manual of the receiver unit (control panel) to learn

how to enter the enrolling mode to enroll the detector. Install the two

provided AAA batteries into the detector (polarity is marked in the detector)

and leave it uncovered. The detector will generate an enrollment signal after

the batteries are installed.

Detector testing

Attach the detector’s cover and from this moment the detector will be in a

testing mode for 5 minutes and each triggering will be indicated by detector’s

LED. Five minutes after the cover was closed, the detector will automatically

enter the normal mode and its LED indicator will be switched off (battery

energy saving function). Open and close the detector‘s cover to reset the

testing mode for an additional 5 minutes if needed.

Note: if you change DIP switch’s setting, the system accepts the new

setting after the detector cover is closed.

Normal operating mode of the detector

The detector, in normal operating mode, conserves battery energy. It will

not indicate triggering with its LED. Information about each triggering is

transmitted to the system. The detector performs self testing regularly and

reports its condition to the system for full supervision.

Battery testing and replacement

The detector checks its batteries conditions automatically. If it is necessary

to replace its batteries, the detector will inform the system about the need for

new batteries. In this mode the detector works as normal, but each triggering

is indicated with a flash of its LED. This way it is possible to recognize, that

the replacement of the batteries is requested. If a low battery is indicated, it

should be replaced as soon as possible (in a week).

Before the batteries are replaced, the receiver (control panel) must be put

into the mode which allows the opening of the detector (User or

Programming mode).

Use only high quality alkaline AAA batteries for replacement. After

installation of the new batteries the detector will be in testing mode and each

triggering will be indicated by detector’s LED. Five minutes after the cover is

closed, the detector will automatically enter the normal mode and its LED

indicator will be switched off (battery energy saving function).

fax: 420-428-313183

tel.: 420-428-346911

www.jablotron.cz

export@jablotron.cz

Pod Skalkou 33

466 01 Jablonec nad Nisou

Czech Republic

Produkt Specifikationer

Mærke:	Joblotron
Kategori:	Overvågningskamera
Model:	JA-60M

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron JA-60M stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Joblotron Manualer

Joblotron H-915 Manual

13 Maj 2024

Joblotron JA-60 Manual

18 April 2024

Joblotron JA-63E Manual

17 April 2024

Joblotron SP-02 Manual

6 April 2024

Joblotron GS-130 Manual

6 April 2024

Joblotron UC-230 Manual

1 April 2024

Joblotron UC-261 Manual

27 Marts 2024

Joblotron JA-60M Manual

6 Marts 2024

Joblotron JA-80A Manual

6 Marts 2024

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Reolink Altas Go PT Manual

31 December 2026

Digital Watchdog MEGApix DWC-MPTZ230XTW Manual

30 December 2026

Verkada CY53-E Manual

28 December 2025

Tracer DinoCam Manual

28 December 2025

I-PRO WV-U25301-F3L Manual

28 December 2025

I-PRO WV-U21501-V3L Manual

27 December 2025

I-PRO WV-U15501-V3L Manual

27 December 2025

Canon CR-N350 Manual

25 December 2025

I-PRO WV-U15301-V3L Manual

25 December 2025

I-PRO WV-U11301-F3 Manual

25 December 2025