Joblotron UC-230 Manual

Joblotron Overvågningskamera UC-230

Læs gratis den danske manual til Joblotron UC-230 (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 80 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 40.5 anmeldelser. Har du et spørgsmål om Joblotron UC-230, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
UC-230 Remote Control Switch 1/2 MEW51204
UC-230 Remote Control Switch
Description
The UC-230 electronic switch can replace a standard mechanical wall
switch. It is directly powered from the mains (230 V AC). By pressing the
switch up or down it works as a standard mechanical switch. At the same
time a built-in receiver in the UC-230 enables reception of control signals
transmitted from RC-xx remote controls or JA-60 wireless detectors. Thus
the mains electric circuit can be switched on or off using a remote control
or automatically when a wireless detector is triggered. Different operating
modes can be used (2 minutes pulse, over switching, on/off).
Specification:
Power supply mains 230 V, 50 Hz
Switch output 25 W – 300 W
Built-in fuse F1.6 A
Coverage class IP 40
Operating temperature indoor, -10°C to +40°C
Working frequency 433.92 MHz
Working range (open area) RC-11 – max. 30 m
RC-22, RC-28, JA-60P, N – max. 100 m
Number of RC remotes or JA-60 detectors max.8
Note: If a momentary consumption is 2 A (for maximum 10 seconds)
and the permanent load doesn’t exceed 300 W, then a 2 A fuse can be
used (fluorescent lamps).
Complies with EN 60950, EN 300220, ETS 300683.
Hereby, Jablotron Ltd., declares that this UC-230 is in compliance with
the essential requirements and other relevant provisions of Directive
1999/5/EC.
Original of the conformity assessment can be found at the web page
www.jablotron.cz, section Technical support.
Installation
The UC-230 switch should be mounted as a usual wall switch.
Follow these steps:
• Switch off the power and remove the old switch
• Open the cover using a small
screw driver (see picture)
• Connect the wires to the terminals
• Attach the housing to the junction
box with screws (button A up)
• Close the cover (LED indicator
must be in the upper right corner)
• Switch on the power supply
• Test the switch manually (press
upper part to switch it on, lower part
to switch it off)
In order to use the UC-230 for controlling fluorescent lamps with
consumption bellow 25W, connect the KF-01 compensation filter in
parallel to the lamp. This filter eliminates lamp flickering when it is
switched off.
Enrolling wireless remote controls and/or detectors
To enroll remote controls and/or wireless detectors to the UC-230,
proceed with the following steps:
1. Press and hold the upper side of the UC-230 (next to the LED
indicator) for 10 seconds.
2. The red LED will flash to confirm entering the learning mode.
3. Press a button of a remote control or insert batteries to a wireless
detector. The LED will turn off confirming that the accessory has
been enrolled.
4. You can repeat steps 1 – 4 and enroll more accessories (up to 8).
Note: The enrolling mode will automatically close in 20 seconds if no
accessory has been enrolled.
Operating modes
Enrolled JA-60 wireless detectors trigger the UC-230 for 2 minutes.
If you enroll RC-11 or RC-22 remote controls they will switch on with
one button and off with the other one.
However, you can select other functions for the remote controls. In
the enrolling mode (LED flashes red) press down the lower (B) UC-230
button. The LED color will change every time you press the button.
This allows you to select other operating modes:
Green flash overswitching mode (the enrolled button will
change the switch status every time it is pressed –
on- off-on -…) – suitable for RC-11, RC-22 and
RC-28 remotes.
Yellow flash 2 minutes pulse – the button enrolled in this mode
will trigger the UC-230 switch for 2 minutes
Red flash switch mode (one button on, the other off) –
suitable for RC-11 and RC-22 remotes
Notes:
• The function of the JA-60 wireless detectors remains the same
despite the color of the LED during enrollment (2 min. pulse)
• Permament switch off - If you don't want the UC-230 to be triggered
byenrolled JA-60 detectors, switch off the UC-230 manually once
again. It means, that if red LED flashes on the UC-230, enrolled JA-
60 detectors are bypassed unitll the receiver is switched on again
(manually or by enrolled RC-xx remote control)
• Permanent switching – If you want to have the UC-230 permanently
on, switch it on once again manually. This will obstruct reception of
radio instructions until it is switched off manually by pressing the
lower button.
LED indicator
The LED indicates the following status:
Red light = off
Flashing of red LED - off (enrolled detectors are bypassed)
Green light = on (enrolled detectors are bypassed)
Yellow light = on for 2 minutes
Optional function of the UC-230
The factory default setting (upper button – on, lower button – off) can be
changed if necessary.
After opening the cover (Caution – dangerous voltage inside!) press and
hold the B button and then scroll with the A button through the following
modes:
• Green light = overswitching mode (operated by both the upper and
the lower button)
• Yellow light = 2 minute pulse mode (operated by both the upper
and the lower button)
• Red light = switch mode (factory setting)
Deleting the accessories
Switch the UC-230 to the enrolling mode. Then press and hold the
lower button on the UC-230 switch for 10 seconds. All enrolled items
will be deleted from the memory. LED will confirm this with short green
and red flashes.
UC-230 Remote Control Switch 2/2 MEW51204
Some practical applications of the UC-230
1. Forgotten corridor switch
If it is required to control light from different places (e.g. in a corridor or
passage) and this was “forgotten“ when the electric installation was
designed, the solution is simple. The existing light switch will be
replaced with the UC-230 and up to 8 RC-22 remote controls can be
used to control it from a distance.
2. Bathroom light switch
If you want to control light in a bathroom from a place where ordinary
switch cannot be used for safety reasons (close to the bath tub or
wash basin), you can replace the ordinary switch with a UC-230. An
RC-22 remote control can safely switch it on or off.
3. Outdoor lighting control
When you arrive at your house you can use the RC-11 remote control
(usually used to control a Jablotron car alarm or automobile’s central
locking) to switch on an outdoor light. In order to do this you should
enroll the simultaneous pressing of both RC-11 buttons to the UC-230
in the overswitching mode or in the 2 minutes pulse mode.
4. Automatic corridor light
If you replace the ordinary light switch with the UC-230 one, you can
enroll the JA-60 wireless detectors to it. Usually the JA-60N door
contact is used (triggering the switch if a door is opened) or JA-60P
motion detector (triggering the switch if human monition is detected).
At the same time the detectors can be part of the security system.
When the JA-60P is used with the UC-230, the battery saving feature
must be set to the Energy saving level. You have to press and keep
pressed the tamper switch when inserting batteries in the detector.
This way the sleeping mode will be set to 1 minute.
5. Switching the lights permanently off
You can switch off the UC-230 manually and override the triggering
signals from enrolled JA-60 detectors (e.g. during the daylight). This
status is indicted by the flashing red LED.
6. Wireless doorbell with automatic light switch
The RC-28 doorbell button is usually used with the UC-260 acoustic
indicator creating a wireless doorbell. You can also enroll the RC-28 to
the UC-230 in a pulse mode. When the RC-28 is pressed both the UC-
260 will sound and a light can be switched on. This way you can light
up the entrance hall or indicate a visitor to people with poor hearing.
The triggered light may also prevent intruders entering your house
during your absence.
7. Child switch
If a small child is in the house, sometimes it is difficult for him to switch
on the lights. You can help him if your replace the ordinary switch with
the UC-230 and place RC-22 remote switches on the wall at a desired
height.
Note: Although this product does not contain any harmful materials we
suggest you to return the product to the dealer or directly to the producer after
usage.

Produkt Specifikationer

Mærke: Joblotron
Kategori: Overvågningskamera
Model: UC-230

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron UC-230 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera Joblotron Manualer

Joblotron

Joblotron H-915 Manual

13 Maj 2024
Joblotron

Joblotron JA-60 Manual

18 April 2024
Joblotron

Joblotron JA-63E Manual

17 April 2024
Joblotron

Joblotron SP-02 Manual

6 April 2024
Joblotron

Joblotron GS-130 Manual

6 April 2024
Joblotron

Joblotron UC-230 Manual

1 April 2024
Joblotron

Joblotron UC-261 Manual

27 Marts 2024
Joblotron

Joblotron JA-60M Manual

6 Marts 2024
Joblotron

Joblotron JA-80A Manual

6 Marts 2024
Joblotron

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Swann

Swann SWDVK-846808MQBWF Manual

13 August 2025
Tenda

Tenda RT3 Manual

13 August 2025
Lorex

Lorex LWB3801 Manual

13 August 2025
Swann

Swann SWDVK-856808MQB Manual

13 August 2025
Swann

Swann SWDVK-446854D Manual

13 August 2025
Swann

Swann SONVK-1689808B8D Manual

13 August 2025
Swann

Swann SONVK-1690008DE Manual

13 August 2025
Swann

Swann SWDVK-84880W4AOC Manual

13 August 2025
Swann

Swann SRDVR-165580H Manual

13 August 2025
Swann

Swann SONVK-1689808 Manual

13 August 2025