Joblotron UC-261 Manual

Joblotron Overvågningskamera UC-261

Læs gratis den danske manual til Joblotron UC-261 (4 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Joblotron UC-261, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
UC-261 wireless indoor siren 1 / 2 MFI52702
The UC-261 wireless indoor siren
The UC-261 indoor siren communicates wirelessly with the
control panel (two way communication). It can be used as a
wireless indoor siren and at the same time as a melody doorbell
or as a chime indicator. The UC-261 is compatible with Jablotron
wireless control panels (JA-63 and JA-65), JA-60 wireless
detectors and RC-4x, RC-22 and RC-28 remote controls.
Several triggering devices can be used simultaneously and
different melodies can be assigned to each device. Two different
sound levels can be selected. The UC-261 can also provide
entrance and exit delay chirps when used with a control panel.
In addition, if the UC-261 is disconnected from the power it will
send an error report to the control panel.
Specification
Power supply 230 V, 50 Hz
Power consumption 1 W
Acoustics 8 melodies and/or 100 dB/m alarm siren
Input wireless devices max. 8 remote controls or detectors
1 control panel, JA-63 or JA-65
Class II according to EN60950
Working frequency 433.92 MHz
Environmental conditions indoors –10 to +40°C
Safety standards IP40 according to EN 60529, IEC 529
Jablotron Ltd. hereby declares that the UC-261 is in
compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
The original of the conformity assessment can be found at
www.jablotron.com, Technical Support section.
Installation
The UC-261 is powered directly from a power outlet. The
device should not be installed close to any metal structures or
other objects obstructing radio signal transmissions.
Enrolling of wireless devices:
1. To enroll the JA-63 or 65 control panel switch the control
panel to enrollment mode.
2. While pressing and holding a button on the UC-261,
plug it into the outlet to transmit the enrollment signal.
3. Release the button when you hear two beeps. The flashing
button indicates that it is in programming mode.
Consequently the UC-261 will be enrolled to siren position “A”.
4. If another wireless siren has already been enrolled to the
control panel, then it is necessary to enroll the UC-261 to a
detector position by entering 000000 in control panel
enrollment mode before plugging the UC-261 into the outlet
(see also the control panel manual).
5. Exit enrollment mode of the control panel by pressing N.
6. If it is necessary to enroll other devices to the UC-261, see
following procedure (points 7 to 9). Or exit programming
mode by briefly pressing the button on the UC-261.
NOTE:
• If position “A” is occupied and you plug the UC-261
into the outlet in control panel enrollment mode, then
the former item (e.g. JA-60A) will be deleted.
• Only one control panel can be enrolled to the UC-261 but
more UC-261 units can be enrolled to one control panel.
A
la
r
m
-
S
ir
e
n
W
ir
el
e
s
s
b
u
tt
on
s
-
d
o
o
r
be
ll
JA
-6
0
de
te
ct
or
s
-
n
oti
fi
ca
tio
n
Movement
JA-60P
Door open
JA-60N
RC-22
RC-28
Control panel
JA-6x
UC-261 wireless indoor siren 1 / 2 MFI52702
The UC-261 wireless indoor siren
The UC-261 indoor siren communicates wirelessly with the
control panel (two way communication). It can be used as a
wireless indoor siren and at the same time as a melody doorbell
or as a chime indicator. The UC-261 is compatible with Jablotron
wireless control panels (JA-63 and JA-65), JA-60 wireless
detectors and RC-4x, RC-22 and RC-28 remote controls.
Several triggering devices can be used simultaneously and
different melodies can be assigned to each device. Two different
sound levels can be selected. The UC-261 can also provide
entrance and exit delay chirps when used with a control panel.
In addition, if the UC-261 is disconnected from the power it will
send an error report to the control panel.
Specification
Power supply 230 V, 50 Hz
Power consumption 1 W
Acoustics 8 melodies and/or 100 dB/m alarm siren
Input wireless devices max. 8 remote controls or detectors
1 control panel, JA-63 or JA-65
Class II according to EN60950
Working frequency 433.92 MHz
Environmental conditions indoors –10 to +40°C
Safety standards IP40 according to EN 60529, IEC 529
Jablotron Ltd. hereby declares that the UC-261 is in
compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
The original of the conformity assessment can be found at
www.jablotron.com, Technical Support section.
Installation
The UC-261 is powered directly from a power outlet. The
device should not be installed close to any metal structures or
other objects obstructing radio signal transmissions.
Enrolling of wireless devices:
1. To enroll the JA-63 or 65 control panel switch the control
panel to enrollment mode.
2. While pressing and holding a button on the UC-261,
plug it into the outlet to transmit the enrollment signal.
3. Release the button when you hear two beeps. The flashing
button indicates that it is in programming mode.
Consequently the UC-261 will be enrolled to siren position “A”.
4. If another wireless siren has already been enrolled to the
control panel, then it is necessary to enroll the UC-261 to a
detector position by entering 000000 in control panel
enrollment mode before plugging the UC-261 into the outlet
(see also the control panel manual).
5. Exit enrollment mode of the control panel by pressing N.
6. If it is necessary to enroll other devices to the UC-261, see
following procedure (points 7 to 9). Or exit programming
mode by briefly pressing the button on the UC-261.
NOTE:
• If position “A” is occupied and you plug the UC-261
into the outlet in control panel enrollment mode, then
the former item (e.g. JA-60A) will be deleted.
• Only one control panel can be enrolled to the UC-261 but
more UC-261 units can be enrolled to one control panel.
A
la
r
m
-
S
ir
e
n
W
ir
el
e
s
s
b
u
tt
on
s
-
d
o
o
r
be
ll
JA
-6
0
de
te
ct
or
s
-
n
oti
fi
ca
tio
n
Movement
JA-60P
Door open
JA-60N
RC-22
RC-28
Control panel
JA-6x

Produkt Specifikationer

Mærke: Joblotron
Kategori: Overvågningskamera
Model: UC-261

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron UC-261 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera Joblotron Manualer

Joblotron

Joblotron H-915 Manual

13 Maj 2024
Joblotron

Joblotron JA-60 Manual

18 April 2024
Joblotron

Joblotron JA-63E Manual

17 April 2024
Joblotron

Joblotron SP-02 Manual

6 April 2024
Joblotron

Joblotron GS-130 Manual

6 April 2024
Joblotron

Joblotron UC-230 Manual

1 April 2024
Joblotron

Joblotron UC-261 Manual

27 Marts 2024
Joblotron

Joblotron JA-60M Manual

6 Marts 2024
Joblotron

Joblotron JA-80A Manual

6 Marts 2024
Joblotron

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

AVer

AVer HUB35-EXT35 Manual

11 December 2025
4XEM

4XEM SD8111 Manual

11 December 2025
4XEM

4XEM VIVOTEK Manual

11 December 2025
4XEM

4XEM MD7560 Manual

10 December 2025
AVer

AVer MT100 Manual

10 December 2025
4XEM

4XEM 4X-FD7132 Manual

10 December 2025
Telycam

Telycam Vision+ N3 Manual

7 December 2025
FLIR

FLIR FC-690 AI Manual

5 December 2025
FLIR

FLIR FH-625 R Manual

5 December 2025
FLIR

FLIR FC-644 AI-R Manual

5 December 2025