Joblotron JA-80M Manual

Joblotron Overvågningskamera JA-80M

Læs gratis den danske manual til Joblotron JA-80M (1 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 80 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 40.5 anmeldelser. Har du et spørgsmål om Joblotron JA-80M, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

The JA-80M wireless magnetic door detector 1 MHQ51405

The JA-80M wireless magnetic door detector

The JA-80M is a component of Jablotron’s Oasis 80 alarm system. It is

designed to detect the opening of doors, windows etc. It can also be

extended by a normally closed sensor. The battery-powered detector

communicates via OASIS radio protocol.

MG OFF

MG ON

tamper

switch

external

sensor

Reaction

mag. sensor

ON/OFF

INSTANT

DELAY

magnet

LITHIUM

3,6V AA

Installation

Installation shall only be undertaken by technicians holding a certificate

issued by an authorized distributor.

This detector reacts to the removal of its magnet unit. The electronics

should be installed onto the non-moving part of windows or doors, and the

magnet onto the moving part. The detector should be installed vertically.

Avoid locating it directly on a metal frame as metal influences the

functioning of the magnetic sensor and radio communication. If the door

or window is made of metal, we recommend installing the detector unit

away from the metal and wiring up an external wired magnetic sensor

which is connected to the detector. See the following instructions:

5. 1. Open the detector cover by pressing the tab in.

6.2. Screw the rear cover to the solid part of the door/window.

7.3. Attach the magnet to the moving part of the window. Its

distance from the detector should not exceed 5mm when the

door/window is closed. The lower edge of the magnet should be

aligned with the lower edge of the detector. Only a single magnet

can be installed, either on the left side or the right side of the

detector.

8. 4. Leave the battery disconnected and the cover open and

then follow the control panel or receiver manual. The basics of

enrollment are:

4.1. Enter enrollment mode on the control panel by keying in “1” in

Service mode.

5.2. Install a battery into the detector to activate enrollment.

6.3. Exit enrollment mode by pressing “#”

After installing a battery into the detector, allow up to 30 seconds for

stabilisation. During this period the LED is continuously lit.

To enroll a detector after having already connected a battery, first

disconnect the battery, and press and release the tamper sensor to

discharge any remaining charge to ready the device for enrollment.

DIP switches

MG ON / MG OFF Allows the internal magnetic sensor inside the

detector to be disabled when the detector is only to be used with external

sensors wired to its terminals.

INS / DEL DEL provides entrance & exit delays for detectors installed in

a building entrance. INS allows the detector to instantly trigger alarm

activation if the control panel is armed. This DIP switch (INS/DEL) only

has an effect if the detector has a natural reaction assigned to its

address in the Oasis control panel.

It also has no effect when used with a

UC-8x or AC-8x receiver.

Opening the cover makes the detector react with a tamper signal.

Open/closed status detection

The detector is factory-set to indicate both opening and closing so that the

control panel knows the status of doors/windows. If a pulse mode is

desired to indicate only opening, keep the tamper switch pressed while

installing the battery. Not pressing the tamper switch gives open and closed

status signals.

Wiring up the external sensor

External sensors can be wired to the detector. It is possible to protect more

doors/windows or to wire in other types of wired detectors. There are two

inputs, IN and TMP which react when disconnected from the GND common

terminal.

IN: If the IN terminal is disconnected from GND it sends the same signal to

the control panel as if the magnet had been removed from the detector. The

internal magnetic sensor can be disabled by DIP switch if desired.

TMP: The TMP terminal sends a tamper signal to the control panel if

disconnected from GND.

Note: If any of these two inputs is not used, it must be shorted to the GND

terminal.

Wiring example

Testing the detector

15 minutes after closing the detector cover, the LED indicates detector

triggering. The strength and quality of detector signals can be measured

by the control panel in Service mode.

Battery replacement

The detector monitors its battery voltage and if too low, a transmission is

sent to the control panel to inform the installer or user. The detector

continues to function and shows each triggering of the detector with a flash

of its LED. Battery replacement should not be delayed by more than two

weeks. This should be done by a qualified technician with the control panel

in Service mode.

Expired batteries should not be thrown into the garbage, but disposed of

according to local regulations.

Removing the detector from the system

If a detector is removed, the control panel announces the removal. The

detector has to be deleted in the control panel before intentional removal.

Technical parameters

Voltage: Lithium battery type LS(T)14500 (3,6V AA)

Typical battery lifetime: approx. 3 years for 20 daily activations maximum

Communication band: 868 MHz, Oasis protocol

Communication range: approx. 300m (open area)

Typical sensitivity range of the built-in magnetic sensor 45/25mm

Inputs for external sensors IN and TMP = normally closed loops

Dimensions 110 x 31 x 26 mm

magnet: 56 x 16 x 15 mm

Operational environment according to EN 50131-1 II. Indoor general

Operational temperature range -10 to +40 °C

EN 50131-1,CLC/TS 50131-2-6, EN 50131-5-3 classification: grade 2

Complies with ETSI EN 300220, EN50130-4, EN55022, and EN 60950-1

Can be operated according to ERC REC 70-03

FCC ID VL6JA80M

Jablotron Ltd. hereby declares that the JA-80M is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC and complies with

part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This

device may not cause harmful interference, and 2. This device must accept any

interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications no expressly approved by Jablotron could void

the user´s authority to operate the equipment. The original of the conformity

assessment can be found at www.jablotron.com, Technical Support section

Note: Although this product does not contain any harmful materials we suggest you

return the product to the dealer or

directly to the producer after use.

Produkt Specifikationer

Mærke:	Joblotron
Kategori:	Overvågningskamera
Model:	JA-80M

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron JA-80M stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Joblotron Manualer

Joblotron H-915 Manual

13 Maj 2024

Joblotron JA-60 Manual

18 April 2024

Joblotron JA-63E Manual

17 April 2024

Joblotron SP-02 Manual

6 April 2024

Joblotron GS-130 Manual

6 April 2024

Joblotron UC-230 Manual

1 April 2024

Joblotron UC-261 Manual

27 Marts 2024

Joblotron JA-60M Manual

6 Marts 2024

Joblotron JA-80A Manual

6 Marts 2024

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

AVer HUB35-EXT35 Manual

11 December 2025

11 December 2025

11 December 2025

10 December 2025

10 December 2025

4XEM 4X-FD7132 Manual

10 December 2025

Telycam Vision+ N3 Manual

7 December 2025

FLIR FC-690 AI Manual

5 December 2025

FLIR FH-625 R Manual

5 December 2025

FLIR FC-644 AI-R Manual

5 December 2025