Joblotron JA-80PB Manual

Joblotron Overvågningskamera JA-80PB

Læs gratis den danske manual til Joblotron JA-80PB (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 83 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 42 anmeldelser. Har du et spørgsmål om Joblotron JA-80PB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

The JA-80PB wireless motion/glass-break detector MHP52504 1

The JA-80PB wireless PIR motion/glass-break detector

The JA-80PB is a component of Jablotron’s Oasis 80 alarm system. It consists

of two independent detectors which occupy two separate enrollment

addresses in the control panel. The motion detector uses a PIR sensor. The

glass-break detector uses the analysis of air pressure variations combined with

the characteristic sound of glass breaking. The product is designed for internal

use in buildings. The battery-powered detector communicates via OASIS radio

protocol.

Lithium 3.6 V

PIR movement detector

Lithium

3.6V

Glass-break detector

Installation

Installation shall only be undertaken by technicians holding a certificate issued

by an authorized distributor. The detector can be installed on a flat wall or in

the corner of a room. Within the detection range of the PIR sensor avoid the

presence of objects rapidly changing in temperature, such as electrical

heaters, gas appliances etc. Moving objects with a temperature close to that of

humans such as curtains moving above a radiator, and pets should also be

avoided. Detectors should not face windows or spotlights or be near fast-

moving air e.g. near ventilation fans or open windows or doors. Because of its

sensitivity to air pressure changes and sounds it should not be located close to

air conditioning or ventilation outlets. There should be no sources of vibration

or audible sounds in the protected area. There should also be no obstacles

blocking the detector’s “view” of the protected area. Keep the detector away

from metal objects which could interfere with radio communication.

Warning: The most frequent cause of false alarms is bad detector-positioning

Do not arm this detector if there are any people or pets moving within the

protected area.

1. Open the detector cover by pressing the tab and disconnect the cable to

the module located in the front cover.

2. Remove the internal PIR module held by an internal tab.

3. Punch screw holes through the rear plastic cover. At least one screw

should penetrate the tamper-sensitive section.

4. Screw the rear cover to the wall, about 2 metres above the floor

(vertically, with the tab down).

5. Return the PIR module to its original place.

6. Leave the battery disconnected and the cover open and then follow

the control panel or receiver manual. The basics of enrollment are:

a. Enter enrollment mode on the control panel by keying in “1” in

Service mode.

b. Install a battery in the PIR detector to activate its enrollment.

c. Install a battery in the glass-break detector and then connect its

cable to the PIR module. This will activate its enrollment to the

next vacant address in the control panel. This means that the

glass-break detector enrolls after the PIR does.

d. Exit enrollment mode by pressing “#”

To observe EN 50131-2-2 the tab must be secured by the supplied screw.

To enroll a detector after having already connected batteries, first disconnect

the batteries, and press and release the tamper sensor to discharge any

remaining charge to ready the device for enrollment. After installing batteries

into the detector, allow two minutes for stabilisation. During this period the LED

is continuously lit.

PIR module DIP switches

NORM / HIGH: selection of immunity to false alarms. The NORM position

combines very good immunity with fast sensor reactions. The HIGH position

gives increased immunity with a slower reaction time and is only used for

problematic installations.

INS / DEL. DEL provides entrance & exit delays for detectors installed in a

building entrance. INS allows the detector to instantly trigger alarm activation

if the control panel is armed. This DIP switch (INS/DEL) only has an effect if

the detector has a natural reaction assigned to its address in the Oasis

control panel. It also has no effect when used with a UC-8x or AC-8x receiver.

Glass-break module DIP switches

DEL / INS selects the reaction of the control panel if glass-breaking is

detected. DEL provides entrance & exit delays and is recommended for

detectors installed near a building’s entrance door. INS allows the detector to

instantly trigger alarm activation if the control panel is armed. This DIP switch

(INS/DEL) only has an effect if the detector has a natural reaction assigned to

its address in the Oasis control panel. It also has no effect when used with a

UC-8x or AC-8x receiver.

PIR / GBS: This selects whether PIR or glass-break triggering is shown by the

LED. Changing this setting only has an effect during the first 15 minutes after

closing the cover (test mode).

Note: Although both detectors are located in one housing, they do act

independently. Each one has its own address. Each one also has its own

selectable reaction via DIP switches in the detector or in SERVICE mode on

the control panel.

Testing the detector

15 minutes after closing the detector cover, the LED shows PIR or glass-beak

detector triggering according to what was previously selected by the PIR/GBS DIP

switch during test mode. The strength and quality of detector signals can be

measured by the control panel in Service mode.

With the DIP switch in position PIR, short LED flashes indicate the processing of

movement triggering the detector. Long flashes show that movement detection is

being signalled to the control panel.

With the DIP switch in position GBS, the LED flashes very briefly when air

pressure changes occur, e.g. a soft knock on a window. A long flash indicates

triggering by breaking glass and the transmission of a signal to the control panel.

Testing and adjusting the glass-break sensor:

• Using a suitable tool or a hand protected by gloves, one by one, knock all

the windows that should be under the detector’s protection. A visible

deformation of the glass should occur but without any damage.

• The deformation of glass causes a change in the air pressure of the room

which makes the LED on the detector flash quickly. The DIP switch must

be in the GBS position.

• Sensitivity to air pressure changes can be adjusted by a potentiometer on

the glass-break sensor PCB located inside the front cover of the detector.

Turning clockwise increases sensitivity. Avoid selecting too high a

sensitivity as this can cause a short battery lifetime.

• The complete function of the glass-break detector can be tested with a

GBT-212 glass-break simulator. After knocking the glass, this simulator

will automatically generate the characteristic sound of breaking glass to

create the conditions for detector triggering.

• If there are any devices in the detector’s protected area generating sound

such as air conditioning, heating, fax machines, refrigerators, etc., check

that they are not triggering alarms by emitting sounds like breaking glass.

Produkt Specifikationer

Mærke:	Joblotron
Kategori:	Overvågningskamera
Model:	JA-80PB

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron JA-80PB stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Joblotron Manualer

Joblotron H-915 Manual

13 Maj 2024

Joblotron JA-60 Manual

18 April 2024

Joblotron JA-63E Manual

17 April 2024

Joblotron SP-02 Manual

6 April 2024

Joblotron GS-130 Manual

6 April 2024

Joblotron UC-230 Manual

1 April 2024

Joblotron UC-261 Manual

27 Marts 2024

Joblotron JA-60M Manual

6 Marts 2024

Joblotron JA-80A Manual

6 Marts 2024

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

AVer HUB35-EXT35 Manual

11 December 2025

11 December 2025

11 December 2025

10 December 2025

10 December 2025

4XEM 4X-FD7132 Manual

10 December 2025

Telycam Vision+ N3 Manual

7 December 2025

FLIR FC-690 AI Manual

5 December 2025

FLIR FH-625 R Manual

5 December 2025

FLIR FC-644 AI-R Manual

5 December 2025