Joblotron JA-80W Manual

Joblotron Overvågningskamera JA-80W

Læs gratis den danske manual til Joblotron JA-80W (1 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 127 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 64 anmeldelser. Har du et spørgsmål om Joblotron JA-80W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

JA-80W wireless combined PIR + MW detector 1 MLI51101

JA-80W wireless combined PIR + MW detector

The JA-80W is a component of Jablotron’s Oasis alarm system. It is

designed to detect human body movement inside buildings. A high immunity to

false alarms is reached thanks to the combination of PIR and microwave (MW)

detection. The PIR part, if triggered, starts the MW detection to confirm PIR

activation. Only then is the triggering transmitted.

Installation

Installation shall only be undertaken by technicians holding a certificate

issued by an authorized distributor. There should be no obstacles blocking the

detector’s “view” of the protected area. Keep the detector away from metal

objects which could interfere with radio communication and the MW field.

Description: 1. DIP-switch; 2. MW part connector; 3.PCB tab; 4. tamper-switch; 5.

PIR sensor; 6. front cover tab; 7. MW sensitivity setting; 8. MW detector

1. Open the detector cover by pressing the tab (6) and remove the PCB

which is held by an internal tab (3) Avoid touching the internal PIR

element or damaging the antenna.

2. Punch screw holes through the rear plastic cover according to the

installation point, either for a corner or for a flat wall At least one screw

should penetrate the tamper-sensitive section.

3. Screw the rear cover to the wall, about 2.5 meters above the floor

(vertically, with the tab down).

4. Return the PCB to its original place till the tab (3) clicks..

5. Leave the battery disconnected and the cover open and then follow the

control panel or receiver manual. The basics of enrollment are:

• Enter enrollment mode on the control panel by keying in “1” in

Service mode.

• Install a battery into the detector to activate enrollment.

• Exit enrollment mode by pressing “#”

6. Close the detector cover till the tab clicks. The supplied screw can secure

the tab.

7. After installing a battery into the detector, allow three minutes for

stabilization. During this period the LED is continuously lit.

Notes:

To enroll a detector after having already connected a battery, first disconnect

the battery, and press and release the tamper switch to discharge any

remaining charge to get the device ready for enrollment.

The detector can also be enrolled by entering the serial number – the last

eights numbers of the barcode, which is placed inside the detector.

To follow the EN 50131-2-4 the tab must be secured by the supplied screw.

DIP switch Setting

Switch no.1: DEL / INS: OFF (DEL) provides entrance & exit delays for

detectors installed in a building entrance route. The ON (INS) allows the

detector to instantly trigger alarm activation if the control panel is armed.

DIP switch no.1 only has an effect if the detector has a natural reaction

assigned to it in the OASiS control panel. It also has no effect when used with

a UC-8x or AC-8x receiver.

Switch no.2: PIR NORM / HIGH: selection of immunity to false alarms.

The OFF (NORM) position combines very good immunity with fast sensor

reactions. The ON (HIGH) position gives increased immunity with a slower

reaction time and is only used for problematic installations.

Switch no.3: MW NORM / HIGH sets the time period after PIR detection in

which the MW detection is active. The position OFF – 1 s, ON – 2 s

Switch no.4: MW NORM / TEST. The position OFF is for the standard function

of the detector. The MW detection is triggered by the PIR detection part for one or

two seconds according to switch no.3. The position ON - MW detection works

continuously for testing purposes (walk test).

Testing the detector

15 minutes after closing the detector cover, the LED indicators show detector

activation. A short flash of the red light indicates PIR detection and a long flash

(2 sec) indicates MW confirmation of the movement.

For the proper functioning of the detector, it is essential to set the MW

detection field according to the place which should be monitored. For setting

up, switch the fourth DIP switch to the TEST position. Sensitivity (monitoring

range) can be adjusted by a potentiometer on the MW detection part located

inside the front cover of the detector. Turning clockwise increases the

sensitivity (range). Avoid selecting too high a sensitivity as the detection can

cover e.g. nearby rooms. Generally the MW detection field should be the same

as the PIR detection one. After setting up, switch the DIP switch back to

NORM position.

To save battery energy, the PIR detector switches to battery-save mode 15

minutes after the cover is closed. During battery-save mode the PIR sensor still

always watches out for movement. The first movement detected and consecutively

confirmed by the MW part is then signaled to the control panel instantly, and for the

next 5 minutes the PIR sensor ignores any further movement. After these 5

minutes, the PIR sensor then returns to watching out for movement until re-

triggered.

Battery replacement

The detector regularly checks its battery conditions. If battery voltage is

too low, then the report is sent to the control panel to inform the user or

installer. The detector continues to work and each detected movement is

confirmed by a brief LED flash. The battery should be replaced within two

weeks by a qualified technician in SERVICE mode.

After battery replacement, test the functioning of the detector. Expired

batteries should not be thrown into the garbage, but disposed of according

to local regulations.

Removing the detector from the system

If a detector is removed, the control panel reports the removal. The detector

has to be deleted from its address in the control panel before intentional

removal.

Detection characteristics

Technical parameters

Power supply: Lithium battery type LS(T)14500 (3.6V / 2,4 Ah AA)

Typical battery lifetime: approx. 2 years (DIP switch 3: NORM)

Communication band: 868 MHz, Oasis Protocol

Communication range: approx. 300m (open area)

Recommended installation height: 2.0 to 2.5 m above floor level

PIR detection angle/detection range: 110° / 12 m (with basic lens)

MW detection range / frequency 0.5 to 20 m / 9.35 GHz

Operational environment according to EN 50131-1 II. indoor general

Operational temperature range -10 to +40 °C

EN 50131-1, EN 50131-2-4, EN 50131-5-3 classification: grade 2

Dimensions, weight 110 x 60 x 55 mm, 140 g

Complies with ETSI EN 300220, ETSI EN 300 440-1, EN 50130-4, EN 55022, EN 60950-1

Can be operated according to ERC REC 70-03

Operation requires notification national telecommunication offices of Finland, France, Italy,

Serbia and Montenegro, Spain, Sweden, UK

JABLOTRON ALARMS a.s. hereby declares that the

JA-80W is in compliance with the essential requirements

and other relevant provisions of Directive 99/5/EC. The

original of the conformity assessment can be found at

www.jablotron.com, Technical Support section

Note: Although this product does not contain any harmful

materials we suggest you return the product to the dealer or

directly to the producer after use.

Produkt Specifikationer

Mærke:	Joblotron
Kategori:	Overvågningskamera
Model:	JA-80W

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron JA-80W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Joblotron Manualer

Joblotron H-915 Manual

13 Maj 2024

Joblotron JA-60 Manual

18 April 2024

Joblotron JA-63E Manual

17 April 2024

Joblotron SP-02 Manual

6 April 2024

Joblotron GS-130 Manual

6 April 2024

Joblotron UC-230 Manual

1 April 2024

Joblotron UC-261 Manual

27 Marts 2024

Joblotron JA-60M Manual

6 Marts 2024

Joblotron JA-80A Manual

6 Marts 2024

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

AVer HUB35-EXT35 Manual

11 December 2025

11 December 2025

11 December 2025

10 December 2025

10 December 2025

4XEM 4X-FD7132 Manual

10 December 2025

Telycam Vision+ N3 Manual

7 December 2025

FLIR FC-690 AI Manual

5 December 2025

FLIR FH-625 R Manual

5 December 2025

FLIR FC-644 AI-R Manual

5 December 2025