JUNG 844.20W Manual

JUNG Ikke kategoriseret 844.20W

Læs gratis den danske manual til JUNG 844.20W (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om JUNG 844.20W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Speed regulator

Art.-No.: 245.20

Speed regulator

Art.-No.: 844.20W

Operationsmanual

1 Safety instructions

Electrical equipment may only be installed and fitted by electrically skilled persons.

Danger of electric shock. Always disconnect before carrying out work on the devise or

load. At the same time, take into account all circuit breakers that supply dangerous

voltage to the device or load.

Danger of electric shock. Device is not suitable for disconnection from supply voltage.

Failure to observe the instructions may cause damage to the device and result in fire and

other hazards.

These instructions are an integral part of the product, and must remain with the end

customer.

2 Device components

picture 1: Device components

(1) Speed controller

(2) Frame

(3) Central plate

(4) Adjusting knob

(5) Fuse holder

(6) Measuring points for voltage test

Test L: Outer conductor

Test7: Motor output

Test8: Switching output

(7) Release lever for plug-in terminal

(8) Adjuster

1/6

32554413

J:0082554413 17.08.2010

picture 2: Circuit schematic

IN Rated current = I1 + I2 = max. 2.7 A

I1 Motor current

I2 Switching output current

3 Function

Intended use

- Speed controller for speed control of single-phase motors such as induction, shaded-pole

or universal motors

- Installation in appliance box to DIN 49073 acc.

Product characteristics

- Short-circuit protection through fine-wire fuse

- Electronic over-temperature protection

- Switching output e.g. for ohmic loads or for activating ventilation openings

The maximum load capacity of the switching output depends on the motor current.

By reducing the motor current it is possible to switch slats or ohmic loads with higher

current consumption.

- Measuring points (picture 2) make it possible to check the connected voltages without

dismantling the speed controller.

i The device may hum slightly due to the noise suppression choke. This does not represent

any defect in the device.

i Operation with a changeover switch is not possible.

4 Operation

Switching the motor on

o Turn the control button to the right.

The motor switches on to maximum speed. The switching output is activated.

Adjusting the speed

o Minimum speed: turn control button all the way to the right.

o Increase speed: turn control button to the left. The maximum speed is reached just before

the far left position.

Switching the motor off

o Turn the control button all the way to the left.

2/6

32554413

J:0082554413 17.08.2010

Speed regulator

Produkt Specifikationer

Mærke:	JUNG
Kategori:	Ikke kategoriseret
Model:	844.20W

Har du brug for hjælp?

Hvis du har brug for hjælp til JUNG 844.20W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret JUNG Manualer

3 Juni 2025

31 December 2025

14 December 2024

10 December 2024

10 December 2024

JUNG MACD1193WW Manual

10 December 2024

JUNG WS10D Manual

10 December 2024

JUNG AL1561.07F Manual

10 December 2024

JUNG 1745DSTE Manual

10 December 2024

JUNG MALS1193 Manual

10 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet Audio P100CPA Manual

15 Juni 2025

Sabrent BK-MAC2 Manual

15 Juni 2025

Planet Audio P9950CPA Manual

15 Juni 2025

Filmcity FC-CTH-01 Manual

15 Juni 2025

Cleveland 22CGT6 Manual

15 Juni 2025

Auray SVRK-4U-S Manual

15 Juni 2025

Bobrick B-2860 Manual

15 Juni 2025

Sony ODBK-103 Manual

15 Juni 2025

Planet Audio P70CPA Manual

15 Juni 2025

Gourmia GAF657 Manual

15 Juni 2025