Kenwood Excelon X502-1 Manual

Kenwood Modtager Excelon X502-1

Læs gratis den danske manual til Kenwood Excelon X502-1 (7 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Kenwood Excelon X502-1, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
Safety precautions
WARNING
To prevent injury or re, take the following precau-
tions:
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and
wiring work to professionals.
• When extending the ignition, battery, or ground wires,
make sure to use automotive-grade wires or other
wires with the range of 5 mm2 (AWG 10) or more to
prevent wire deterioration and damage to the wire
coating.
• To prevent a short circuit, never put or leave any metal-
lic objects (such as coins or metal tools) inside the unit.
• If the unit starts to emit smoke or strange smells,
turn off the power immediately and consult your
KENWOOD dealer.
• Do not touch the unit during use because the sur-
face of the unit becomes hot and may cause burns if
touched.
CAUTION
To prevent damage to the machine, take the follow-
ing precautions:
• Be sure the unit is connected to a 12 V DC power sup-
ply with a negative ground connection.
• Do not open the top or bottom covers of the unit.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
• When replacing a fuse, only use a new one with the
prescribed rating. Using a fuse with the wrong rating
may cause your unit to malfunction.
• To prevent a short circuit when replacing a fuse, rst
disconnect the wiring harness.
NOTE
• If you experience problems during installation, consult
your KENWOOD dealer.
• If the unit does not seem to be working right, consult
your KENWOOD dealer.
Cleaning the unit
If the front panel gets dirty, turn o the power and wipe
the panel with a dry silicon cloth or soft cloth.
CAUTION
Do not wipe the panel with a hard cloth or a cloth damp-
ened by volatile solvents such as paint thinner and alco-
hol. They can scratch the surface of the panel and / or
cause the indicator letters to peel o .
To prevent battery rise
When the unit is used in the ACC ON position without
turning the engine ON, it depletes the battery. Use it after
starting the engine.
Protection function
The protection function is activated in the following
situations:
This unit is equipped with a protection function for
protecting this unit and your speakers from various acci-
dents or problems that can occur.
When the protection function is triggered, the power
indicator goes o and the ampli er stops operating.
• When a speaker wire may be short-circuited.
• When a speaker output contacts ground.
• When the unit malfunctions and a DC signal is sent to
the speaker output.
• When the internal temperature is high and unit won’t
operate.
Wiring
• Take the battery wire for this unit directly from the bat-
tery. If it’s connected to the vehicle’s wiring harness, it
can cause blown fuses etc.
• If a buzzing noise is heard from the speakers when the
engine is running, connect a line noise lter (optional)
to each of the battery wire.
• Do not allow the wire to directly contact the edge of
the iron plate by using Grommets.
• Connect the ground wire to a metal part of the car
chassis that acts as an electrical ground passing elec-
tricity to the battery‘s negative ⊖ terminal. Do not turn
the power on if the ground wire is not connected.
• Be sure to install a protective fuse in the power cord
near the battery. The protective fuse should be the
same capacity as the unit’s fuse capacity or somewhat
larger.
• For the power cord and ground, use a vehicle type
( reproof) power wring cord. (Use a power wiring cord
with the range of 5 mm2 (AWG 10) or more.)
• When more than one power ampli er are going to be
used, use a power supply wiring wire and protective
fuse of greater current-handling capacity than the total
maximum current drawn by each ampli er.
Speaker selection
• Using speakers with smaller input ratings than the
ampli er’s output power would result in smoke gener-
ation or equipment failure.
• Use speakers that have an impedance of 2 Ω or greater.
When more than one set of speakers are going to be
used, calculate the combined impedance of the speak-
ers and then connect suitable speakers to the ampli er.
<Example>
X502-1
CLASS D MONO POWER AMPLIFIER
INSTRUCTION MANUAL
AMPLIFICATEUR MONO CLASSE D
MODE D’EMPLOI
AMPLIFICADOR DE POTENCIA CLASE D MONOFÓNICO
MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from
your new power ampli er.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the
space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for
information or service on the product.
Model X502-1 Serial number
US Residence Only
Register Online
Register your Kenwood product at w ww.kenwood.com/usa
B5A-2739-00 / 00 (KV / WV)© 2018 JVC KENWOOD Corporation
Combined
impedance
Installation / Installation / Instalación
213 mm (8-3/8 )̯
53 mm (2-1/16 ) (5-7/8 )̯149 mm ̯
Installation procedure
Since there are large variety of settings and con-
nections possible according to applications, read
the instruction manual well to select the proper
setting and connection.
1. Remove the ignition key and disconnect the
negative ⊖ terminal of the battery to prevent
short circuits.
2. Set the unit according to the intended usage.
3. Remove the Dressing cover.
4. Connect the input and output wires of the
units.
5. Connect the speaker wires.
6. Connect the power wire, power control wire
and grounding wire following this order.
7. Install the installation ttings in the unit.
8. Attach the unit.
9. Attach the Dressing cover.
10. Connect the negative ⊖ terminal of the
battery.
CAUTION
• Do not install in the below locations;
(Unstable location, In a location that interferes
with driving, In a location that gets wet, In a
dusty location, In a place that gets hot, In a
place that gets direct sunlight, In a location that
gets hit by hot air)
• Do not install the unit under the carpet.
Otherwise heat build-up occurs and the unit
may be damaged.
• Install this unit in a location which allows heat
to easily dissipate. Once installed, do not place
any object on top of the unit.
• The surface temperature of the amplifier will
become hot during use. Install the ampli er in
a place where people, resins, and other sub-
stances that are sensitive to heat will not come
into contact with it.
• When making a hole under a seat, inside the
trunk, or somewhere else in the vehicle, check
that there is nothing hazardous on the oppo-
site side such as a gasoline tank, brake pipe,
or wiring harness, and be careful not to cause
scratches or other damage.
• Do not install near the dashboard, rear tray, or
air bag safety parts.
• The installation to the vehicle should securely
fasten the unit to a place in which it will not
obstruct driving. If the unit comes o due to a
shock and hits a person or safety part, it may
cause injury or an accident.
• After installing the unit, check to make sure that
electrical equipment such as the brake lamps,
turn signal lamps and windshield wipers oper-
ate normally.
Procédure d’installation
Etant donné que le nombre de réglages et de
raccordements est assez important, il importe
de prendre pleinement connaissance du mode
d’emploi.
1. Retirer la clé de contact et débrancher la
borne négative ⊖ de la batterie pour éviter les
court-circuits.
2. Régler l’appareil en fonction de l’utilisation
désirée.
3. Déposer l’enjoliveur.
4. Raccorder les câbles d’entrée et de sortie de
l’appareil.
5. Raccorder les câbles de haut-parleur.
6. Relier, dans l’ordre, le câble d’alimentation,
le câble de commande d’alimentation et le
câble de masse.
7. Mettre en place les accessoires d’installation
sur l’unité.
8. Brancher l’unité.
9. Fixer l’enjoliveur.
10. Raccorder la borne négative ⊖ de la batterie.
ATTENTION
• Ne pas procéder à l’installation de l’appareil
si vous trouvez dans l’un des lieux suivants;
(Lieu instable, Lieu où la conduite du véhicule
peut être gênée, Lieu exposé à l’humidité, Lieu
exposé à la poussière, Lieu surchauffé, Lieu
exposé directement à la lumière du jour, Lieu
exposé à l’air chaud)
• Ne pas recouvrir l’appareil d’une nappe, tapis,
etc; la chaleur qui s’accumulerait risque d’en-
dommager l’appareil.
•
Installer cet appareil à un emplacement tel que
la chaleur puisse se dissiper aisément. Après
l’installation, ne placer aucun objet sur l’appareil.
• La surface de l’ampli cateur va chau er pen-
dant l’utilisation. Installer l’amplificateur à
un endroit où des passagers, de la résine ou
d’autres substances sensibles à la chaleur n’en-
treront pas en contact avec lui.
•
Lors du forage d’un trou sous le siège, à l’intérieur
du co re ou partout ailleurs dans le véhicule, véri-
er s’il n’y a pas d’élément dangereux de l’autre
côté, tel qu’un réservoir à carburant, une conduite
de frein, une gaine de câbles, et faire attention de
ne pas faire de gri es ou d’autres dégâts.
•
Ne pas l’installer près du tableau de bord, de la
plage arrière ou d’éléments de sécurité de l’airbag.
•
Lors de l’installation dans un véhicule, l’appareil doit
être fermement xé à un endroit ou il ne gênera pas
la conduite. Si l’appareil se détache suite à un choc
et heurte quelqu’un ou un élément de sécurité, il
peut occasionner des blessures ou un accident.
• Après installation de l’appareil, s’assurer que
les di érents équipements électriques tels que
lampes frein et les clignotants de direction
fonctionnent normalement.
Procedimiento de instalación
Como se puede hacer una gran variedad de
ajustes y conexiones según las aplicaciones, lea
atentamente el manual de instrucciones para
seleccionar el ajuste y la conexión apropiados.
1. Retire la llave de encendido y desconecte el
terminal negativo ⊖ de la batería para evitar
cortocircuitos.
2. Prepare el aparato según el uso que vaya a
hacer de él.
3. Quite la cubierta de adorno.
4. Conecte los cables de entrada y salida de las
unidades.
5. Conecte los cables del altavoz.
6. Conecte el cable de alimentación, el cable de
control de alimentación y el cable de tierra en
este orden.
7. Coloque los elementos de instalación en la
unidad.
8. Coloque la unidad.
9. Coloque la cubierta de adorno.
10. Conecte la terminal negativa ⊖ de la batería.
PRECAUCIÓN
• No instale el equipo en las siguientes ubica-
ciones; (Ubicación inestable; En un lugar que
inter era a la conducción; En un lugar en el que
pueda mojarse; En un lugar con exceso de polvo;
En un lugar en el que pueda recalentarse; En un
lugar en el que reciba la luz directa del sol; En un
lugar situado en el ujo de aire caliente)
• No utilice el aparato bajo una alfombra porque
en caso contrario, éste podría sobrecalentarse y
estropearse.
• Instale este aparato en un lugar donde el calor
pueda disiparse fácilmente. Una vez instalado,
no ponga nada sobre él.
• La temperatura de la super cie del ampli cador
se elevará durante su uso. Instale el ampli ca-
dor en un lugar seguro donde personas, resinas
y otras substancias sensibles al calor no entren
en contacto con esta super cie.
• Cuando haga un ori cio bajo el asiento o en el
portaequipajes o en algún otro lugar del vehí-
culo, veri que que no existan objetos peligrosos
al lado opuesto tales como un tanque de gaso-
lina, tubo del freno, o los alambres del cableado
del coche y tenga cuidado de no rayar las piezas
del vehículo o causar algún otro daño.
•
No lo instale cerca del panel de controles, bandeja
trasera, o piezas de seguridad del colchón de aire.
• La instalación de esta unidad debe ser realizada
en un lugar donde no estorbe la conducción.
Si la unidad se sale de su posición debido a un
choque y golpea a una persona o a alguna pieza
de seguridad, puede causar o un accidente.
• Después de instalar el aparato, cerciórese de que
los equipos eléctricos (luces de freno, intermiten-
tes y limpiadores) funcionen normalmente.
Accessories / Accessoires / Accesorios
①
Ø4×16 mm
Self-tapping screws
Vis taraudeuses
Tornillo autorroscantes 4
②Speaker level input cable
Câble d’entrée de niveau d’enceinte
Cable de entrada del nivel de altavoces 1
Installation board, etc. (thickness: 15 mm or more)
Tableau d’installation, etc. (épaisseur: 15 mm ou plus)
Tablero de instalación, etc. (grosor: 15 mm o más)
① Parts included
Pièces comprises
Partes incluidas
Dressing cover
Enjoliveur
Cubierta de adorno

Produkt Specifikationer

Mærke: Kenwood
Kategori: Modtager
Model: Excelon X502-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Kenwood Excelon X502-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager Kenwood Manualer

Kenwood

Kenwood X5001-1 Manual

24 Juli 2025
Kenwood

Kenwood X8001-5 Manual

23 Juli 2025
Kenwood

Kenwood X3001-4 Manual

23 Juli 2025
Kenwood

Kenwood DMX6523DABS Manual

14 Juli 2025
Kenwood

Kenwood eXcelon DMX9724XDS Manual

21 Juni 2025
Kenwood

Kenwood eXcelon DAX8000XDS Manual

20 Juni 2025
Kenwood

Kenwood DMX9724XS Manual

19 Juni 2025
Kenwood

Kenwood Excelon X303-4 Manual

20 Februar 2025
Kenwood

Kenwood Excelon X803-5 Manual

20 Februar 2025
Kenwood

Kenwood Excelon X503-1 Manual

18 Februar 2025

Modtager Manualer

Nyeste Modtager Manualer

CYP

CYP AU-A220 Manual

30 Juli 2025
Sirus

Sirus I-Amp 8.150T Manual

30 Juli 2025
AER

AER Colourizer 2 Manual

30 Juli 2025
Sirus

Sirus I-Amp 1.300T Manual

30 Juli 2025
PAC

PAC AP4-FD32 Manual

30 Juli 2025
CYP

CYP PUV-1540S-RX Manual

30 Juli 2025
ART

ART USB Dual Pre Manual

29 Juli 2025
SSL

SSL Pure Drive Quad Manual

29 Juli 2025
SSL

SSL Pure Drive Octo Manual

29 Juli 2025
CYP

CYP PUV-1550SRX Manual

29 Juli 2025