Kicker DXA250.1 Manual

Kicker Modtager DXA250.1

Læs gratis den danske manual til Kicker DXA250.1 (24 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 56 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 28.5 anmeldelser. Har du et spørgsmål om Kicker DXA250.1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/24

DXA

AMPLIFIERS

Owner’s Manual

DXA250.1 | DXA500.1

DXA1000.1 | DXA1500.1

Manual del Propietario | Español

AMPLIFICADOR DEL LA SERIE DXA.1

Benutzerhandbuch | Deutsch

MONOVERSTÄRKER DER DXA.1-SERIE

Manuel d’utilisation | Française

AMPLIFICATEUR DE SÉRIE DXA.1

2014 DXA Mono Amps Rev B.indd 1

2014 DXA Mono Amps Rev B.indd 12014 DXA Mono Amps Rev B.indd 1 8/2/2013 3:12:12 PM

8/2/2013 3:12:12 PM

8/2/2013 3:12:12 PM8/2/2013 3:12:12 PM

DXA.1-SERIES AMPLIFIERS

OWNER’S MANUAL

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER ampliﬁ er. Make sure there are no items

behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open

ventilation for the ampliﬁ er. If possible, mount the ampliﬁ er in the climate-controlled passenger compartment. Drill

four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the ampliﬁ er.

Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the

ampliﬁ er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,

metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the

battery’s negative post and the vehicle chassis is recommended.

The DXA ampliﬁ er has dual input sensitivity differential RCA inputs which will receive either high or low level

signals from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs

to the stereo RCA input on the end panel of the ampliﬁ er using the KICKER KISL as shown (make sure you set

the DXA ampliﬁ er’s input level switch to “HI”). Alternatively, the signal can be delivered to the ampliﬁ er using the

low-level RCA outputs on the source unit. Set the input level switch on the end panel of the ampliﬁ er to “LO”.

Either input method will provide a low-level output signal at the RCA output, which effectively passes the audio

signal to another ampliﬁ er or component. Keep the audio signal cable away from factory wiring harnesses and

other power wiring. If you need to cross this wiring, cross it at a 90 degree angle.

PERFORMANCE

Authorized KICKER Dealer:

Purchase Date:

Model Number:

Serial Number:

Model: DXA250.1 DXA500.1 DXA1000.1 DXA1500.1

RMS Power [Watts]

@ 14.4V, 4Ω mono, ≤ 1% THD+N

@ 14.4V, 2Ω mono, ≤ 1% THD+N

125 x 1

250 x 1

500 x 1

1000 x 1

750 x 1

1500 x 1

Length [in, cm] 8-1/8, 21 8-1/8, 21 12-1/16, 31 14, 36

Speciﬁ cations common to all models:

Height [in, cm] 2-3/8, 6

Width [in, cm] 7-3/16, 18

Frequency Response [Hz] 25–200

Signal-to-Noise Ratio [dB] >95, A-weighted, re: rated power

Input Sensitivity Low Level: 125mV–5V

High Level: 250mV–10V

Electronic Crossover Variable Lo-pass 50Hz–200Hz, 12dB/octave

KickEQ™ Bass Boost Variable 0–12dB @ 40Hz

Subsonic Filter 25Hz, 24dB/octave

Remote Bass Yes (sold separately)

MODEL: DXA250.1 | DXA500.1 | DXA1000.1 | DXA1500.1

2014 DXA Mono Amps Rev B.indd 2

2014 DXA Mono Amps Rev B.indd 22014 DXA Mono Amps Rev B.indd 2 8/2/2013 3:12:19 PM

8/2/2013 3:12:19 PM

8/2/2013 3:12:19 PM8/2/2013 3:12:19 PM

Produkt Specifikationer

Mærke:	Kicker
Kategori:	Modtager
Model:	DXA250.1
Bredde:	161.8 mm
Dybde:	82.1 mm
Højde:	86 mm
Produktfarve:	Sort
Højpasfilter:	Ja
Lavpasfilter:	Ja
Signal/støjforhold:	95 dB
Antal forstærkerkanaler:	2 kanaler
RMS udgangseffekt pr. kanal (4 Ohm):	250 W
Højpasfilterområde:	25 - 200 Hz
Lavpasfilterområde:	50 - 200 Hz
RMS udgangseffekt pr. kanal (2 ohm):	125 W
Indgangsfølsomhed:	250 mV