with powerful motion-activated LED work light and surge protection.
CONTENTS
• 29602 Power Strip Pro
• This Instruction Sheet
GENERAL SPECIFICATIONS
• Operating Altitude: 6562' (2000 m)
• Operating Temperature: 14° to 140°F (-10° to 60°C)
• Storage Temperature: -4° to 158°F (-20° to 70°C)
• Relative Humidity: 85% non-condensing
• AC Power Cord: 6' (1.8 m), 14 AWG, NEMA 5-15P
• AC Power Cord Jacket: SJTW (105C/300V)
• AC Input: 125V AC, 15A, 60Hz (nominal)
• AC Output: 125V/15A, 60Hz, Max. output 1875W
• AC Outlets: 5 × NEMA 5-15R,
• Surge Protection: 2160 Joules, Type 3, 600V (L-N, L-G, N-G)
• Over-Current Protection: 125V, 15A
• USB Output (Total Wattage): 27W
• USB-A: 2 × 5V DC, 2.4A (shared)
• USB-C: 1 × 5V DC, 3.0A
• LED Work Light Output: 500 Lumens
• Magnets: Neodymium, N48
• Dimensions: 1.85" × 1.70" × 23.0" (4.7 cm × 4.3 cm × 58.4 cm)
• Weight: 2.07 lbs (0.94 kg)
• Drop Protection: 6.6' (2 m)
• Standards: Conforms To UL STD. 1363
Certied To CSA STD. C22.2 NO. 308
Specifications subject to change.
WARNINGS
Read, understand, and follow these instructions to ensure
safe operation and service of the Power Strip Pro. Failure
to observe these warnings can result in re, electric
shock, property damage, serious injury and/or death.
• Use indoors and in dry locations only. expose to moisture, DO NOT
rain, or snow.
• DO NOT plug into another relocatable power tap or an extension cord.
• DO NOT use the product if damaged or modified.
• DO NOT subject to impacts or drops greater than 6.6' (2 m)
(Product Drop Rating). Drops larger than this may not show signs
of damage, but internal components may have been compromised.
It is advisable to replace the unit if any such severe events occur.
• Keep away from high voltage devices.
• DO NOT exceed maximum power rating of device (1875W).
• DO NOT connect to an ungrounded outlet.
• DO NOT use with extension cord adapters that eliminate the
connection to ground.
• NOT for permanent installation – remove the plug for DO NOT
permanent connection to the electrical system.
• High intensity LED Light. Avoid looking directly at the work light.
• DO NOT attempt to insert other USB connector types into the
USB-C and USB-A ports.
• CAUTION - DO NOT install this device if there is not at least 10
meters (30 feet) of wire between the electrical outlets and the
electrical service panel.
• This device features an internal protection that will disconnect the
surge protective component at the end of its useful life, but will
maintain power to the load – now unprotected.
SYMBOLS ON PRODUCT
Warning or Caution
Risk of Electrical Shock
Do Not Stare at Operating Lamp: Visible Radiation
Strong Magnetic Field
Read Instructions
Motion Sensor
Auto-Power Off (10 Minutes)
3s
Press for 3 Seconds
Settings
Level VI Efciency Standard
Independently tested by Intertek and meets
applicable standards.
V
E
R
I
F
I
E
D
Energy Efciency Veried
FEATURE DETAILS (FIG.A)
1 AC Power On/Off Switch
2 125V AC Outlets (×5)
3 USB-A Charging Ports (×2)
4 USB-C Charging Port
5 Grounded Input LED Indicator
6 Surge Protection LED Indicator
7 500-Lumen LED Work Light
8 Work Light Motion Sensor
9 Work Light On-Off / Program Button
10 Rare-Earth Mounting Magnets (×2)
11 16" On-Center Through Mounting Holes with Location Markers
12 16" On-Center Keyholes with Location Markers
13 15" On-Center Keyholes with Location Markers
14 AC Power Cord
15 Strain Relief
MOUNTING INSTRUCTIONS
NOTE: Disconnect Power Strip Pro from power source before mounting.
NOTE: NOT for permanent mounting.
When mounting with a threaded fastener or nail, mark the centerpoints onto
the mounting surface using the Mounting Locations on the desired mounting
holes
11
,
12
,
13
, the mounting template from the side panel of the retail
packaging, or download/print the template using the QR code on the front of
this manual. It is recommended to pre-drill pilot holes when using threaded
fasteners.
• Through Holes
11
can accommodate up to a 3/8" (9.5 mm) shank
diameter.
• Keyholes
12
,
13
can accommodate up to #8 screws or 10d nails.
NOTE: When mounting via Through Holes
11
, tighten fasteners by hand. DO
NOT USE POWER TOOLS TO TIGHTEN.
The Power Strip Pro can also be mounted to steel surfaces via the Rare-Earth
Mounting Magnets
10
on the back of the unit.
OPERATING INSTRUCTIONS
SUPPLYING POWER
Plug the AC Power Cord
14
into a functional standard U.S. 125V AC receptacle
to supply power to the unit.
Turn on the AC Power Switch
1
to supply power to the AC Outlets
2
, USB
ports
3
,
4
and Work Light
7
.
NOTE: Grounded Input LED Indicator
5
will illuminate when an active
ground is present on AC supply.
NOTE: Surge Protection Status Indicator
6
will illuminate when the unit is
surge protected.
PROGRAMMING WORK LIGHT
7
The integrated work light has both manual and automatic functionality:
To manually turn the Work Light on and off, press the Work Light On-Off /
Program Button
9
.
To program the Work Light's behavior, press and hold the Work Light On-Off
/ Program Button
9
for greater than three seconds to enter Programming
Mode. Repeatedly press the Work Light On-Off / Program Button
9
to cycle
through the different modes, as indicated by the flashing color of the Work
Light On-Off / Program Button
9
. To enter your desired mode, allow the
Work Light On-Off / Program Button
9
to flash the appropriate color for 5
seconds, then press the Work Light On-Off / Program Button
9
. There are
3 modes:
• AUTO-ON/OFF MODE (GREEN):
The Work Light
7
turns ON automatically when motion is detected in a
predetermined range. The Work Light
7
remains ON as long as motion is
detected, and automatically powers OFF after 10 minutes of detecting no
motion. The Work Light
7
may also be manually switched ON/OFF at any
time by pressing the Work Light On-Off / Program Button
9
. See MOTION
SENSOR section for more details.
NOTE: In AUTO ON/OFF Mode, if the Work Light
7
is turned OFF
manually, there will be a 60-second delay before the motion sensor
activates the Work Light again.
• MANUAL-ON/AUTO-OFF MODE (BLUE):
The Work Light
7
turns ON when user manually presses and releases
Work Light On-Off / Program Button
9
. The work light remains ON as
long as the device detects activity. The Work Light
7
remains ON as long
as motion is detected, and automatically powers OFF after 10 minutes of
detecting no motion. The Work Light
7
may also be manually switched
OFF at any time by pressing the Work Light On-Off / Program Button
9
.
NOTE: In MANUAL ON/AUTO OFF Mode, the Work Light
7
will not
power-ON from motion detection.
• MANUAL-ON/OFF MODE (RED):
The Work Light
7
turns ON and/or OFF when user manually presses and
releases Work Light On-Off / Program Button
9
.
NOTE: In MANUAL ON/OFF Mode, the Work Light
7
will not power-ON
or OFF from motion detection.
NOTE: To conserve energy, the Work Light On-Off / Program Button
9
will
stop illuminating 60 seconds after last being pressed. When this happens,
the Power Strip Pro is still powered ON, and the Work Light
7
will continue
to function according to the last saved mode.
NOTE: The Work Light will power-ON in the same mode as it was in when
powered-OFF.
MOTION SENSOR
8
• Detection range averages ~9' (~3 m) from center.
• Coverage may vary depending on lighting and/or mounting conditions.
• Avoid placing the motion sensor in direct sunlight or bright light.
MAINTENANCE
CLEANING: Be sure the device disconnected from all power sources and
devices. Use clean, dry, soft, lint-free cloth to wipe down the entire units.
Do not use abrasive cleaners or solvents.
STORAGE: Store in cool temperatures, mild humidity, and away from
direct sunlight (See GENERAL SPECIFICATIONS). Leaving in a vehicle or
other confined spaces in extreme hot temperatures can lead to decrease
in service life, overheating, or fire. Extreme cold temperatures below
the specified storage range can also harm performance and service
life. Keep away from corrosive chemicals and gases. After taking out of
storage, inspect visually to make sure device and all accessories look
satisfactory. Allow unit to return to ambient conditions before using.
FCC & IC COMPLIANCE
This device complies with part 15 of the FCC RULES and Industry
Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: The grantee is not responsible for any changes or modifications
not expressly approved by the party responsible for compliance. Such
modifications could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device contains license-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s
license-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that
may cause undesired operation of the device.
CAN ICES-003(B) / NMB-003(B)
DISPOSAL / RECYCLE
Do not place equipment and its accessories in the trash.
Items must be properly disposed of in accordance with local
regulations.
See www.epa.gov/recycle for additional
information.
CUSTOMER SERVICE
KLEIN TOOLS, INC.
450 Bond Street, Lincolnshire, IL 60069 1-800-553-4676
customerservice@kleintools.com www.kleintools.com
5027376
