Klein Tools VDV826-602 Manual

Klein Tools Ikke kategoriseret VDV826-602

Læs gratis den danske manual til Klein Tools VDV826-602 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Klein Tools VDV826-602, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Recommended Care and Maintenance of Klein

Grips

WARNINGS:

•

For use by properly trained professionals

ONLY

• Grips are to be used for temporary installation,

NOT

for permanent anchorage.

• When used on or near energized lines - ground, insulate, or isolate grip before pulling.

• Before each use, clean jaw area and inspect grip for proper operation to avoid slippage.

• Always match proper grip to application.

•

DO NOT

exceed rated capacity.

SELECTION:

Three factors are used to select the proper grip application:

1. Type of wire or cable.

2. Outside diameter of wire or cable.

3. Maximum safe load required.

Tools to assist with in proper selection:

1. See our interactive Grip Selection Guide.

2. Contact your local Klein Tools Distributor.

3. Call Klein Tools at or 1-844-395-3235 1-800-KLEIN76.

OSHA INFORMATION:

OSHA requires that all hand tools and equipment be maintained in good working order

and that they be free from damage caused by wear or abuse (OSHA Part 1910, Subpart

P, Section 1910.242). In addition, OSHA Part 1926, Subpart V, Section 1926.955,

paragraphs (C) (7) (ii) and (C) (8) specifically state that: “The manufacturer’s load

rating shall not be exceeded for stringing lines, pulling lines, sock connections, and all

load-bearing hardware and accessories.” “Conductor grips shall not be used on wire rope

unless designed for this application.”

See back for cleaning, lubricating and inspection instructions.

CLEANING:

1. Use the Klein Grip Cleaning Wire Brush (Cat. No. 25450) or emery cloth to

clean the surfaces of grip jaws.

2. Spray cleaner-degreaser on the grip jaws, all joints and all moving parts.

3. Use the Klein Grip Cleaning Wire Brush to remove dirt and debris from jaws.

4. Wipe grips dry with soft cloth.

Repeat all steps until grip is completely clean.

NOTE:

Aluminum strand conductors may have a die-grease coating which can deposit

on grip jaws. ew aluminum conductors should be wiped clean before grip application. N

Grip jaws should be wiped clean of grease before use.

LUBRICATING:

Lubricate all joints and moving parts.

DO NOT LUBRICATE GRIPPING SURFACES OF JAWS.

STORAGE:

Always store grip in a dry, cool place.

INSPECTION:

Carefully inspect jaw condition, proper aligment of jaws and all parts, and possible

distortion caused by exceeding safe-load specifications. Grips should operate smoothly.

Spring-loaded grips should lock open with loop handle in “Down” position and should

close automatically with loop handle “Up.” The Klein parallel jaw grip may be tested by

opening and closing the jaws by hand, exercising proper caution. All parts and rivets

should be checked for distortion.

NEVER ATTEMPT TO REPAIR OR MODIFY ANY GRI .P

Grips that are bent,

misaligned, or otherwise distorted should be discarded and replaced. If there is ever any

question about the safe condition of any grip, please contact Klein Tools directly

at 1-844-395-3235 or 1-800-KLEIN76.

KLEIN TOOLS, INC

Mansfield, TX USA

www.kleintools.com

WARNING: Cancer and reproductive harm – See www.P65Warnings.ca.gov for more information.

Produkt Specifikationer

Mærke:	Klein Tools
Kategori:	Ikke kategoriseret
Model:	VDV826-602

Har du brug for hjælp?

Hvis du har brug for hjælp til Klein Tools VDV826-602 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Klein Tools Manualer

Klein Tools VDV826-705 Manual

12 August 2025

Klein Tools VDV826-602 Manual

12 August 2025

Klein Tools 66188 Manual

29 Juli 2025

Klein Tools 56334 Manual

15 Juli 2025

Klein Tools 56074 Manual

15 Juli 2025

Klein Tools SPF50LOT15 Manual

15 Juli 2025

Klein Tools SPF50SPY55 Manual

15 Juli 2025

Klein Tools 60956 Manual

9 Juli 2025

Klein Tools 50550 Manual

13 Juni 2025

Klein Tools VDV826-704 Manual

3 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

American Audio FLASH 2C Manual

13 August 2025

Rowenta Ultima Ceramic CF7132 Manual

13 August 2025

American Audio Dual Gem LED Manual

13 August 2025

Adj Flat Par CWWW18 Manual

13 August 2025

American Audio V4002 Manual

13 August 2025

American Audio DCD-PRO500 Manual

13 August 2025

American Audio Rainbow PP II Manual

13 August 2025

American Audio Deco 250 Manual

13 August 2025

American Audio Audio Genie II Manual

13 August 2025

Panduit IAEBH6 Manual

13 August 2025