Klein Tools NCVT-3P Manual

Klein Tools Ikke kategoriseret NCVT-3P

Læs gratis den danske manual til Klein Tools NCVT-3P (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Klein Tools NCVT-3P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

ENGLISH

1. NCV Power On/Off Button

2. Flashlight Power On/Off Button

3. Power On/Mode LEDs

4. Voltage Detection LEDs (Inside Tip)

5. Non-Contact Tip

6. Flashlight

7. Pocket Clip

8. O-ring Seal

9. Battery Cap

10. 2x AAA Batteries (Included)

NOTE: There are no user-serviceable parts inside tester.

Botón de encendido y apagado "NCV"

Botón de encendido y apagado del linterna

3. LED de encendido/modo

4. LED de detección de voltaje (en el interior de la punta)

5. Punta para detección y medición sin contacto

6. Linterna

7. Clip de bolsillo

8. Junta tórica

9. Tapa del compartimento de baterías

10. 2baterías AAA (incluidas)

ESPAÑOL

NOTA: El probador no contiene en su interior piezas que

el usuario pueda reparar.

1. Bouton marche/arrêt NCV (test de tension sans contact)

2. Bouton marche/arrêt du lampe de poche

3. VoyantsDEL de marche/mode

4. VoyantsDEL de détection de tension (dans la pointe)

5. Pointe sans contact

6. Lampe de poche

7. Agrafe pour poche

8. Joint torique

9. Couvercle de piles

10. 2pilesAAA (comprises)

FRANÇAIS

REMARQUE: Ce testeur ne contient aucune pièce

réparable par l’utilisateur.

FIG. 1

DURABILITY / DURABILIDAD / DURABILITÉ

Ingress Protection / Protección contra el ingreso /

Protection contre les infiltrations IP67

Drop Protection

Protección ante caídas / Protection contre les chutes 6.6 ft.

(2 m)

Safety Rating

Clasificación de seguridad / Cote de sécurité CAT IV

1000V

SYMBOLS ON TESTER / SÍMBOLOS DEL PROBADOR / SYMBOLES SUR LE TESTEUR

Warning – Risk of electric shock / Advertencia: riesgo de choque eléctrico / Avertissement – Risque d'électrocution

Risk of danger. It is important that users of this tester read, understand, and follow all warnings, cautions, Important information:

safety information, and instructions in this manual before operating or servicing this tester. Failure to follow instructions could result

in death or serious injury.

Riesgo de peligro. Es importante que el usuario de este probador lea, comprenda y respete todas las Información importante:

advertencias, precauciones, instrucciones e información de seguridad incluidas en este manual, antes de poner en funcionamiento el

probador o de realizarle servicios de mantenimiento. No seguir estas instrucciones puede dar lugar a lesiones graves o mortales.

Risque de danger. Il est important que les utilisateurs de ce testeur lisent, comprennent et suivent tous les Information importante:

avertissements, mises en garde, information de sécurité et instructions donnés dans le présent guide avant de faire fonctionner ou de

réparer ce testeur. Le non-respect pourrait entraîner des blessures graves, voire la mort.

Double insulated / Doble aislamiento / Double isolation

Read instructions / Lea las instrucciones / Lire les instructions

Conformité Européenne

Conforms with European Economic Area directives.

Cumple con las normas del Área Económica Europea.

Conforme aux directives de l’Espace économique Européen.

This product has been independently tested by Intertek and meets applicable published standards.

Este producto p1-ha sido probado de manera independiente por Intertek y cumple con las normas publicadas vigentes.

Ce produit a été testé de manière indépendante par Intertek et répond aux exigences des normes applicables.

CAT

For measurements performed at the source of low-voltage installation and outside lines.

Para mediciones realizadas en la fuente de la instalación de bajo voltaje y líneas externas.

Pour des mesures prises à la source d’une installation à faible tension et des lignes extérieures.

NCVT-3P

INSTRUCTIONS – dual-range Non-Contact Voltage Tester with Flashlight (English: page 2)

INSTRUCCIONES – Probador de voltaje sin contacto de rango dual con linterna(Español: página 3)

INSTRUCTIONS – Testeur de tension sans contact à double plage avec lampe de poche (Français : page 4)

• Detects AC voltage from 12 to 1000V with visual & audible indicators

• Flashlight may be used independently of the NCVT

• Detecta voltaje CA de 12V a 1000V mediante indicadores visuales y audibles

• Linterna que se puede utilizar independientemente del NCVT

• Détecte la présence d’une tension allant de 12 à 1000Vc.a. et la signale au moyen d’indicateurs

visuels et sonores

• La lampe de poche peut être utilisée indépendamment de NCVT (TTSC)

ENGLISH

WARNINGS

To ensure safe operation and service of the tester, follow these

instructions. Failure to observe these warnings can result in severe

injury or death.

• Risk of electric shock and burn. Contact with live circuits could result in death or

serious injury.

• Use caution with voltages above 25V AC as a shock hazard may exist.

• A blinking LED or a steadily illuminated LED in the tip and audible beeps indicate

presence of voltage. If no indication, voltage could still be present.

• Before and after each use, verify operation by testing a known working circuit that is

within the rating of this unit.

• Never assume neutral or ground wires are de-energized. Neutrals in multi-wire branch

circuits may be energized when disconnected and must be retested before handling.

• The tester detect voltage if:WILL NOT

• The wire is shielded.

• The operator is not grounded or is otherwise isolated from an effective earth ground.

• The voltage is DC.

• The tester MAY NOT detect voltage if:

• The user is not holding the tester.

• The user is insulated from the tester with a glove or other materials.

• The wire is partially buried or in a grounded metal conduit.

• The tester is at a distance from the voltage source.

• The field created by the voltage source is being blocked, dampened, or otherwise

interfered with.

• The frequency of the voltage is not a perfect sine wave between 50 and 500Hz.

• The tester is outside of operating conditions (listed in Specifications section).

• Operation may be affected by differences in socket design and insulation thickness

and type.

• In bright light conditions, the LED visual indicators will be less visible.

• When powered-ON, one of the “power-ON” LED’s will be illuminated, and a green light

will illuminate the tip.

DO NOT USE TESTER UNLESS ONE OF THE “POWER-ON” LEDs

IS ILLUMINATED.

• Do not use if tester appears damaged or is not operating properly. If in doubt, replace

the tester.

• Do not apply more than the rated voltage as marked on the tester (1000V).

• Do not apply to uninsulated hazardous live conductors.

• Detection above 70V AC in Mode 1, or above 12V AC in Mode 2 is specified under

"normal" conditions as detailed below. The tester may detect at a different threshold at

different conditions, or may not detect at all unless:

• The tip of the tester is within 0.25" (6 mm) of an AC voltage source radiating unimpeded.

• The user is holding the body of the tester with his or her bare hand.

• The user is standing on or connected to earth ground.

• The air humidity is nominal (50% relative humidity – non-condensing).

• The tester is held still.

• Always wear approved eye protection.

• Comply with local and national safety requirements.

• If this product is used in a manner not specified by the manufacturer, protection

provided by the product may be affected.

OPERATING INSTRUCTIONS

SELECTING VOLTAGE TESTING MODE

NCVT-3P can detect voltage in two distinct modes, defined by the

voltage ranges to which the tester is sensitive. Mode 1 detects 70 to

1000V AC, Mode 2 detects 12 to 1000V AC.

With the tester powered-

ON, successive presses of the NCV Power-ON button

will switch

the tester between modes 1 and 2. The Power-ON indicator LED’s

will indicate the currently active mode.

The tester will power-ON in the

mode that was most recently used.

OPERATING INSTRUCTIONS

CHECKING FOR THE PRESENCE OF AC VOLTAGE

1. Press NCV Power On/Off button. After performing a self-test, a

green light will illuminate the tip when no voltage is detected.

2. Prior to use, test on a known live circuit to verify tester

functionality.

3. Place tip of the tester

near AC voltage. If voltage is present,

the unit will emit audible beeps and the LEDs in the tip

will

illuminate:

Mode Power-On

LED Color

12 to 70V AC >70 to 1000V AC

Mode 1

70 – 1000V

Range

Red

No illumination, no

sound Red LED in tip

illuminated, continuous

audible beep

Mode 2

12 – 1000V

Range

Blue

Blue LED in tip

blinking, pulsing

audible beep

Red LED in tip

illuminated, continuous

audible beep

NOTE: In Mode 2, the tester is more sensitive to high voltage sources

and electrically noisy environments. It is recommended to set the

tester to operate in Mode 1 when expected voltages are above 70V AC.

SILENT OPERATION

To activate silent operation, power-ON by pressing and holding the

NCV Power-ON button

for more than 2 seconds. Power-ON in this

manner each time silent operation is desired.

CLEANING

Be sure tester is turned off and wipe with a clean, dry lint-free

cloth.

Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when not in use for a prolonged period

of time. Do not expose to high temperatures or humidity. After

a period of storage in extreme conditions exceeding the limits

mentioned in the General Specifications section, allow the tester to

return to normal operating conditions before using.

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash.

Items must be properly disposed of in accordance with local

regulations. Please see www.epa.gov www.erecycle.org or

for additional information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street, Lincolnshire, IL 60069

1-800-553-4676

customerservice@kleintools.com

www.kleintools.com

MAINTENANCE

BATTERY REPLACEMENT

When the battery is low, the unit will power-on with a blinking red

LED

; at this point the NCVT-3P will disable the flashlight

functionality to conserve battery function for voltage detection.

1. Unscrew the battery cap

and remove/recycle spent batteries.

2. Install two new AAA batteries. Note proper polarity.

3. Screw battery cap tightly to ensure a tight seal with the O-Ring

FUNCTION BUTTONS

NCV POWER ON/OFF BUTTON

To activate the Non-Contact Voltage Testing feature, press and

release the NCV Power button

. All LEDs will illuminate during

self-test, then the tester will emit a single beep, one of the Power

ON LEDs

will illuminate

indicating which NCVT mode is

active (see OPERATING INSTRUCTIONS), and a green light will

illuminate in the tip

. To power-OFF the tester, press and hold the

NCV Power button

. The tester will emit a double beep.

NOTE: The tester will automatically power-OFF following 4 minutes

of inactivity to conserve battery life.

FLASHLIGHT ON/OFF BUTTON

Press the Flashlight Power Button

to turn on the flashlight.

Press again to turn off the flashlight.

NOTE: The flashlight will automatically power-off after 20 minutes

to conserve battery life

CAUTION

• DO NOT attempt to repair this tester. It contains no serviceable parts.

• DO NOT expose tester to extremes in temperature or high humidity.

GENERAL SPECIFICATIONS

The Klein Tools NCVT-3P is a dual-range non-contact voltage tester

(NCVT) with flashlight. It can detect voltage from 70 to 1000V AC

(Mode 1), or from 12 to 1000V AC (Mode 2) for low voltage and

higher sensitivity.

• Environment: Indoor or outdoor

• Measurement Range: Mode 1: 70 to 1000V AC

Mode 2: 12 to 1000V AC

• Frequency Range: 50 to 500 Hz

• Batteries: 2x AAA 1.5V Alkaline

• Operating and Storage Altitude: Up to 6562 ft. (2000 m)

• Operating and Storage Temp: ° ° ° °14 to 122 F (-10 to 50 C)

• Relative Humidity: <95% non-condensing

• Dimensions: 6.0" x 0.96" x 1.16" (152 x 24 x 29 mm)

• Weight: 2.5 oz. (72 g) including batteries

• Pollution degree: 2

• Safety Rating: CAT IV 1000V AC

• Drop Protection: 6.6 ft. (2 m)

• Ingress Protection: IP67

• Standards: EN61010-1:2010, EN61010-2-030:2010,

EN61326-1:2013, EN61326-2-2:2013.

Conforms to UL STD. 61010-1, 61010-2-030

Certied to CSA STD. C22.2 No. 61010-1, 61010-2-030.

Specifications subject to change.

5001748

Produkt Specifikationer

Mærke:	Klein Tools
Kategori:	Ikke kategoriseret
Model:	NCVT-3P

Har du brug for hjælp?

Hvis du har brug for hjælp til Klein Tools NCVT-3P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Klein Tools Manualer

Klein Tools 50550 Manual

13 Juni 2025

Klein Tools VDV826-704 Manual

3 Juni 2025

Klein Tools 34055 Manual

18 Marts 2025

Klein Tools 60957 Manual

18 Marts 2025

Klein Tools 60953 Manual

18 Marts 2025

Klein Tools 34056 Manual

17 Marts 2025

Klein Tools MODbox 54801MB Manual

12 Marts 2025

Klein Tools 56417 Manual

13 Februar 2025

Klein Tools 54825MB Manual

14 Januar 2025

Klein Tools ESF100 Manual

5 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Rean RCJ6FI-V Manual

1 Juli 2025

Econ Connect PV8 Manual

1 Juli 2025

Ikea UTRUSTA 702.711.73 Manual

1 Juli 2025

Emerson FAT2835 Manual

1 Juli 2025

Ikea UTRUSTA 502.472.16 Manual

1 Juli 2025

SilverCrest SGR 150 E1 Manual

1 Juli 2025

Icom ST-4003A Manual

1 Juli 2025

Ikea SMÅSPORRE 804.570.19 Manual

1 Juli 2025

Ikan Onyx OYB15 Manual

1 Juli 2025

BikeYoke Revive 3.0 Manual

1 Juli 2025