Korg TP-2 Manual

Korg Blander TP-2

Læs gratis den danske manual til Korg TP-2 (8 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Korg TP-2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Owner’s Manual

Printed in Japan

Precautions

Location

Using the unit in the following locations can result in a malfunction.

• In direct sunlight

• Locations of extreme temperature or humidity

• Excessively dusty or dirty locations

• Locations of excessive vibration

• Close to magnetic fields

Power supply

Please connect the designated AC/AC power supply to an AC outlet of

the correct voltage. Do not connect it to an AC outlet of voltage other

than that for which your unit is intended.

Interference with other electrical devices

Radios and televisions placed nearby may experience reception

interference. Operate this unit at a suitable distance from radios and

televisions.

Handling

To avoid breakage, do not apply excessive force to the switches or

controls.

Care

If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use

liquid cleaners such as benzene or thinner, or cleaning compounds or

flammable polishes.

Keep this manual

After reading this manual, please keep it for later reference.

Keeping foreign matter out of your equipment

Never set any container with liquid in it near this equipment. If liquid gets

into the equipment, it could cause a breakdown, fire, or electrical shock.

Be careful not to let metal objects get into the equipment. If something

does slip into the equipment, unplug the AC/AC power supply from the

wall outlet. Then contact your nearest Korg dealer or the store where the

equipment was purchased.

THE FCC REGULATION WARNING (for U.S.A.)

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• Unauthorized changes or modification to this system can void the

user's authority to operate this equipment.

CE mark for European Harmonized Standards

CE mark which is attached to our company’s products of AC mains

operated apparatus until December 31, 1996 means it conforms to

EMC Directive (89/336/EEC) and CE mark Directive (93/68/EEC).

And, CE mark which is attached after January 1, 1997 means it

conforms to EMC Directive (89/336/EEC), CE mark Directive (93/68/

EEC) and Low Voltage Directive (73/23/EEC).

Also, CE mark which is attached to our company’s products of Battery

operated apparatus means it conforms to EMC Directive (89/336/

EEC) and CE mark Directive (93/68/EEC).

IMPORTANT NOTICE TO CONSUMERS

This product has been manufactured according to strict specifications

and voltage requirements that are applicable in the country in which it

is intended that this product should be used. If you have purchased

this product via the internet, through mail order, and/or via a tele-

phone sale, you must verify that this product is intended to be used in

the country in which you reside.

WARNING: Use of this product in any country other than that for

which it is intended could be dangerous and could invalidate the

manufacturer’s or distributor’s warranty.

Please also retain your receipt as proof of purchase otherwise your

product may be disqualified from the manufacturer’s or distributor’s

warranty.

KORG INC.

4015-2 Yanokuchi, Inagi-city, Tokyo 206-0812 Japan

TP-2 [ Tube Preamp ]

INPUT 1

INPUT 2

HI-Z

GAIN

TRIM

COMP

SENS

LEVEL METER

+48V

PHANTOM

PHASE

LINK

OUTPUT 2

OUTPUT 1

S/PDIF OUT

SAMPLING

FREQUENCY

44 48 96

OUTPUT

LEVEL

LOWCUT TUBEHA

PAD S/P DIF

TRANSMIT

HI-Z

GAIN

TRIM

COMP

SENS

LEVEL METER

+48V

PHANTOM

PHASE OUTPUT

LEVEL

LOWCUT TUBEHA

PAD

Block diagram

Specifications

Input connectors: XLR-3-31 type (+48 V phantom power, switchable),

1/4” TRS phone jack (balanced / unbalanced is Hi-Z)

Input impedance: 4 k (XLR-3-31), 10 k (TRS phone Jacks),

1 M (TRS phone Jacks is Hi-Z)

Nominal level: –60 dBu to –12 dBu @ TRIM=max. — min PAD OFF

–34 dBu to +14 dBu @ TRIM=max. — min PAD ON

Maximum level: –48 dBu to 0 dBu @ TRIM=max. — min PAD OFF

–22 dBu to +26 dBu @ TRIM=max. — min PAD ON

Hi-Z

– 48 dBu to 0 dBu @ TRIM=max. — min PAD OFF

– 22 dBu to +12 dBu @ TRIM=max. — min PAD ON

Source impedance: ..................................................................................... 600

Vacuum tubes used: ................................................................................. 12AX7

Compression method: Vacuum tube compression using a photocoupler

Principal specifications

Frequency response:

10 Hz - 44 kHz ±1 dB @ output +4 dBu, 10 k load

S/N: ............................................................................................. 85 dB (typical)

A/D conversion: ............................................. 24-bit 64 times oversampling

Sampling frequency: ............................................. 44.1kHz, 48kHz, 96kHz

Analog output

Connectors: ................... XLR-3-32 type, 1/4” TRS phone jack (balanced)

Output impedance: ................................................................................. 150

Nominal level: ....................................................................................... +4 dBu

Maximum level: .................................................................................. +16 dBu

Source impedance: ................................................................ 10k or higher

Digital output

Connectors: .............................................................................. optical, coaxial

Format: ....................................... 24bit S/P DIF (IEC60958 / EIAJ CP-1201)

General

Power supply: .......................................... Included AC/AC power supply

Dimensions:

224(W) x 170(D) x 88(H)mm / 8.82”(W) x 6.69”(D) x 3.46”(H)

(including protrusions)

Weight: ................................................................................. 1.33 kg / 2.93 lbs

Included items

AC/AC power supply, Owner’s manual

Produkt Specifikationer

Mærke:	Korg
Kategori:	Blander
Model:	TP-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Korg TP-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Korg Manualer

15 December 2023

19 Januar 2023

22 December 2022

26 November 2022

Korg SoundLink MW-2408 Manual

11 November 2022

Korg nanoKONTROL2 Manual

19 Oktober 2022

Blander Manualer

Nyeste Blander Manualer

Pyle PLXR3B Manual

9 August 2025

Pyle PLXREQ710P Manual

9 August 2025

Moulinex Prep Mix HM450B10 Manual

8 August 2025

Peavey PV 10 Manual

8 August 2025

Pyle PLXREQ520P Manual

8 August 2025

Pyle PLXR2B Manual

8 August 2025

Karma MMX 54ZM Manual

6 August 2025

Glemm MXP 8C Manual

6 August 2025

Glemm MXP 18C Manual

6 August 2025

Glemm MXP 14C Manual

6 August 2025