Kramer VM-4DKT Manual

Kramer Modtager VM-4DKT

Læs gratis den danske manual til Kramer VM-4DKT (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Kramer VM-4DKT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

VM-4DKT Quick Start

P/N:

2900- 301544QS

Rev:

Scan for full manual

VM-4DKT Quick Start Guide

This guide HELPS you install and use your VM-4DKT for the first time.

Go to www.kramerav.com/downloads/VM-4DKT to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check in the b what’s ox

VM-4DKT 1:4 4K HDMI/DGKAT Distribution Amplier Transmitter

4 Rubber feet

1 Quick start guide

1 Power cord and adapter

IMPORTANT NOTICE!

We highly recommend using only Kramer UNIKAT cables with these products. If using 3

rd party shielded CAT-6A cables, both ends of the

shield must be soldered to the connectors for the products to function properly. Do not use any jumpers, unshielded wall plates or mid-

span cable connections. These extenders are not compatible with HDBaseT technologies. Prior to signal extension, ensure that the

extension line cable is lying straight and not coiled.

Step 2: Get to know your -4DKT VM

Feature

Function

STATUS LED

Red Power . –up

Green Power is –on.

ACTIVE EDID LED

The LED color indicates the active EDID type. When ashing, the state is in the

process of being activated.

Yellow Default EDID. –

Blue Output-acquired EDID. –

Green Custom EDID. –

INPUT LED

On Input signal detected. –

Flashing Source connected, but no signal detected. –

HDMI IN Connector

Connect to an HDMI source.

LOOP Connector

Connect to a local HDMI display.

DGKAT2 OUTPUTS Connectors (x4)

Connect to a DGKat-2.0 receiver (for example, ) using twisted pair cable. PT-872xr

SERVICE 3-pin terminal block

Connect to a serial controller.

SETUP DIP-switches

Sets the device behavior (see Step 6: Operate -4DKTVM ).

Fan Vent

For heat ventilation.

12V DC Power Connector

Connect the V DC power adapter into the device and then connect it to the 12

mains.

Step 3: Mount -4DKT VM

Install -4DKT using one of the following methods: VM

• Attach the rubber feet and place the unit on a at

surface.

• Ensure that the environment (e.g., maximum ambient temperature & air ow) is

compatible for the device.

• Avoid uneven mechanical loading.

• Appropriate consideration of equipment nameplate ratings should be used for avoiding

overloading of the circuits.

• Reliable earthing of rack-mounted equipment should be maintained.

• Maximum mounting height for the device is 2 meters.

Produkt Specifikationer

Mærke:	Kramer
Kategori:	Modtager
Model:	VM-4DKT

Har du brug for hjælp?

Hvis du har brug for hjælp til Kramer VM-4DKT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Kramer Manualer

Kramer WP-DEC7 Manual

17 Oktober 2025

Kramer VM-216H Manual

29 September 2025

Kramer PA-120Z Manual

21 Juli 2025

Kramer VM-114H4C Manual

21 Juli 2025

Kramer VM-80VN Manual

21 Juli 2025

Kramer VM-2HDxl Manual

21 Juli 2025

Kramer DA3-24-H Manual

25 Juni 2025

Kramer PA-50HZ Manual

4 Marts 2025

Kramer PT-102VN Manual

3 Januar 2025

Kramer VM-2H2 Manual

19 December 2024

Modtager Manualer

Nyeste Modtager Manualer

Extron DTP3 R 201 D Manual

15 December 2025

Pure Acoustics Maestra AVD5023 Manual

11 December 2025

Atoll AM400 Evolution Manual

8 December 2025

Atoll MA100 Manual

8 December 2025

Fostex AP25 Manual

7 December 2025

Fostex PC200USB-HR Manual

7 December 2025

Atoll CD400 Evolution Manual

7 December 2025

Fostex PC200USB Manual

7 December 2025

Fostex AP05 Manual

6 December 2025

Atoll AV500 Manual

6 December 2025