La Crosse Technology WT-62U Manual


Læs gratis den danske manual til La Crosse Technology WT-62U (3 sider) i kategorien Termometer. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 5 anmeldelser. Har du et spørgsmål om La Crosse Technology WT-62U, eller vil du spørge andre brugere om produktet?

Side 1/3
1
WT-62U Digital Window Thermometer
Features:
Clear functional design
Easy to read outdoor temperature from indoors
Maximum and minimum values with auto reset
Easy to mount
Weather resistant
Specifications:
Measuring range: -22 ºF to +122 ºF
Resolution: 0.2 ºF
Temperature Updating Interval: Every 10 Seconds
Battery: 1 AAA
Inserting the Battery:
1. The battery cover is located on the back of the
thermometer.
2. Using your fingers slide the battery cover off of the battery compartment.
3. Observing the correct polarity insert one AAA battery into the battery compartment.
4. Replace the battery cover.
Setting the Time:
1. Press the MODE button to enter the setting mode.
2. The hours digits will flash in the center of the display.
3. Press and release the + button to advance the hour.
NOTE: When in the hours between midnight and noon, A.M. will be displayed on the left of the display. When in the
hours between noon and midnight P.M. will be displayed on the left side of the display.
4. Press and release the MODE button to conrm the hour and advance to the minute setting.
5. The minutes digits will flash at the bottom of the display.
6. Press and release the + button to advance the minute.
7. Holding down the + button will advance the minutes faster.
8. Press and release the MODE button to conrm the minutes and exit the time setting mode.
2
NOTE: The thermometer will automatically time out and return to the normal display mode after approximately 30
seconds.
Installation:
1. Select your location for mounting in an area that is easy to view.
NOTE: The design of the thermometer is such that the display will appear
darker when looking at an upward angle at the display. It is recommended to
mount the thermometer slightly above eye level to ensure the best viewing of
the display.
2. Clean the glass surface completely before mounting.
NOTE: Be sure to completely clean the surface of dust and dirt and let the
area dry completely prior to mounting the thermometer. Failure to do
so may result in bad adhesion between the window and holder.
NOTE: Before continuing please be sure the time is set – See the previous
section on Setting the Time
3. Remove the plastic from the adhesive strip.
4. Press the adhesive strip against the glass to adhere the thermometer.
Please note: In order to obtain the most accurate temperature reading be
sure to mount the thermometer out of direct sunlight. Mounting the unit in
direct sunlight will cause artificially high temperature readings.
Use and MAX/MIN temperatures:
The upper display shows the current temperature.
The lower left display shows the minimum temperature.
The lower right display shows the maximum temperature.
The maximum temperature automatically resets at 8:00 A.M.
The minimum temperature automatically resets at 8:00 P.M.
If the time is not set the maximum and minimum temperature will not
be reset at the correct local time.
Maintenance:
Replace the battery when the display becomes weak. * The low battery indicator will appear when the batteries
need to be changed.
Do not expose the instrument to extreme temperatures, vibration or shock
Clean the thermometer with a soft damp cloth only. Do not use solvents or scouring agents.
Please do not try to repair the unit. Contact the original point of purchase or La Crosse Technology Warranty for
repair/ replacement instructions.


Produkt Specifikationer

Mærke: La Crosse Technology
Kategori: Termometer
Model: WT-62U

Har du brug for hjælp?

Hvis du har brug for hjælp til La Crosse Technology WT-62U stil et spørgsmål nedenfor, og andre brugere vil svare dig