LiftMaster 041A6569 Manual

LiftMaster Ikke kategoriseret 041A6569

Læs gratis den danske manual til LiftMaster 041A6569 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om LiftMaster 041A6569, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Be sure power is not connected to the garage door opener
BEFORE installing the safety reversing sensor.
To prevent SERIOUS INJURY or DEATH from a closing garage
door:
• Correctly connect and align the safety reversing sensor. This
required safety device MUST NOT be disabled.
• Install the safety reversing sensor so beam is NO HIGHER
than 6" (15 cm) above garage floor.
Safety Sensor Brackets
Model 41a6569
Be sure power to the opener is disconnected.
The sending eye transmits an invisible light beam to the receiving
eye. The units can be installed on either side of the garage door as
long as the sun never shines directly into the receiving eye lens.
Look at the label on the connector end of each case to identify the
sensors.
The brackets must be connected and fastened so that the sending
and receiving eyes face each other as shown in Figure 1.
If an obstruction breaks the light beam while the garage door is
closing, the door will stop and reverse to full open position, and
the opener lights will fl ash for 5 seconds.
The brackets must be securely fastened to a solid surface such as
the studs on either side of the door, or add a piece of wood at each
location if installing in masonry construction.
The invisible light beam path must be unobstructed. No part of the
garage door (or door tracks, springs, hinges, rollers or other
hardware) can interrupt the beam while the door is closing. If it
does, use a piece of wood to build out each sensor mounting
location to the minimum depth required for light beam clearance.
Invisible Light Beam
Protection Area
Safety Reversing Sensor
6" (15 cm) max. above floor Safety Reversing Sensor
6" (15 cm) max. above floor
Figure 1: Facing the door from inside the garage
2
Install the Safety Reversing Sensor
Figures 2 and 3 show assembly of brackets and "C" wrap based on
the recommended installation of the sensors on each side of the
garage door as shown on page 1. Figures 4 and 5 are variations
which may fi t your installation requirements better.
Make sure the wraps and brackets are aligned so the sensors
will face each other across the garage door.
• Fasten the "C" wraps to the mounting brackets having square
holes, using the hardware shown in Figure 2.
• Connect each assembly to a slotted bracket, using the hardware
shown in Figure 3.
NOTE: the alignment of the brackets for left and right sides of
the door.
• Finger tighten the lock nuts.
• Use bracket mounting holes as a template to locate and drill (2)
3/16" diameter pilot holes on both sides of the garage door, 4"- 6"
above the fl oor (See warning on but not exceeding 6" (15 cm).
page 1.)
• Attach bracket assemblies with 1/4"x1-1/2" lag screws as shown
in Figure 3.
• Adjust right and left side bracket assemblies to the same distance
out from the mounting surface. Make sure all door hardware
obstructions are cleared. Tighten the nuts securely.
Garage
Floor
Inside
Garage
Wall
Alternate Floor Mount
Mounting Bracket
with Slot
Mounting Bracket
with Square Holes
"C" Wrap
Sensor
Indicator Light
Attach with
concrete anchors
(not provided)
"C" Wrap
Inside
Garage
Wall
Mounting Bracket
with Square Holes
Mounting Bracket
with Slot
Alternate Wall Mount
Sensor
Garage
Floor
Indicator Light
Mounting Bracket
with Slot
1/4"-20
Lock Nuts
1/4x1-1/2"
Lag Screws 1/4-20x1/2" Carriage Bolts
(with square shoulder)
Inside
Garage
Wall
"C" Wrap
Mounting Bracket
with Square Holes
Mounting Bracket
With Square Holes
#10-32x3/8"
Screws
"C" Wrap
#10-32
Lock Nuts
Figure 2
Figure 3
Figure 4
Figure 5
Lag Screw 1/4x1-1/2"
Screw
#10-32x3/8"
Lock Nut
#10x32
Staples Carriage Bolts
1/4"-20x1/2"
Lock Nut
1/4"-20
HARDWARE SHOWN ACTUAL SIZE

Produkt Specifikationer

Mærke: LiftMaster
Kategori: Ikke kategoriseret
Model: 041A6569

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 041A6569 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret LiftMaster Manualer

LiftMaster

LiftMaster 041-0405-000 Manual

15 Juni 2025
LiftMaster

LiftMaster LMHNTG Manual

4 September 2024
LiftMaster

LiftMaster CAPXSTKPL Manual

3 September 2024
LiftMaster

LiftMaster BG790 Manual

3 September 2024
LiftMaster

LiftMaster 64LM Manual

3 September 2024
LiftMaster

LiftMaster CAPXSHOOD Manual

28 August 2024
LiftMaster

LiftMaster myQ-SGC2WCH Manual

21 August 2024
LiftMaster

LiftMaster CAPXS Manual

21 August 2024
LiftMaster

LiftMaster MGJ5011U Manual

21 August 2024
LiftMaster

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Festo

Festo DFM-32-100-B-PPV-A-KF Manual

17 Juni 2025
Playtive

Playtive IAN 285777 Manual

17 Juni 2025
Festo

Festo VAEM-L1-S-M3-26 Manual

17 Juni 2025
Festo

Festo DFPC-320 Manual

17 Juni 2025
EFX

EFX ICAK12 Manual

17 Juni 2025
Bearware

Bearware 307294 Manual

17 Juni 2025
Futaba

Futaba MC-9200H/A Manual

17 Juni 2025
Hansgrohe

Hansgrohe AXOR Montreux 16517800 Manual

17 Juni 2025
OmniMount

OmniMount 2N1-S Manual

17 Juni 2025
Festo

Festo DSNU-S-12- -F1A Manual

17 Juni 2025