LiftMaster 050DCTBLKMC Manual

LiftMaster Ikke kategoriseret 050DCTBLKMC

Læs gratis den danske manual til LiftMaster 050DCTBLKMC (12 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om LiftMaster 050DCTBLKMC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

Before you begin

Installation

RECEIVER LOGIC BOARD REPLACEMENT

Models 050DCTBMC and 050DCTBLKMC

1.2 To maintain your warranty,

place the provided label

over the existing label

on the end panel of the

garage door opener.

1.1 Remove the light lens by pulling

the top side of the light lens

and swing the light lens down.

Squeeze the light lens clips to

remove lens from end panel.

1.3 Disconnect electrical and battery

power (if applicable) to the

garage door opener.

Remove the receiver logic board

2.1 Disconnect the wires from the quick-connect terminals

( ). Disconnect any wires from the lock terminals. A

Remove the receiver logic board end panel from the

garage door opener.

2.2 Unplug the wire harnesses from the receiver logic

board. You may need needle-nosed pliers, to

remove the harnesses.

2.3 Remove the receiver

logic board from the

end panel by removing

the 2 screws and

releasing the 2 clips.

To prevent possible SERIOUS INJURY or DEATH:

• Disconnect ALL electric and battery power BEFORE performing ANY

service or maintenance.

Screws

Wire clip

Clips

To insert or remove the wires from the terminal,

push in the tab with a screwdriver tip.

Lock

Terminals

Red

White

Grey

Your garage door opener has an internal gateway located on the receiver logic board. After installing the new receiver logic board, use the myQ

® serial number found on the provided label to add your

garage door opener to your myQ® account. The products illustrated in the instructions are for reference. Your product may look different. The logic board ﬁrmware has been updated. The update provides

a new Obstruction Notiﬁcation that signals when the opener senses resistance, such as an obstruction or other binding in the door and rail system. The door will stop or reverse to open limit and the

opener will beep and the lights ﬂash 5 times.

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause cancer or

birth defects or other reproductive harm. For more information go

to www.P65Warnings.ca.gov.

To prevent damage to the receiver/logic board, DO NOT touch printed

circuit board of replacement receiver/logic board during installation.

ALWAYS wear protective gloves and eye protection when changing the

battery or working around the battery compartment.

NOTE: 050DCTB replaces 050DCTWF and 050DCTBLK replaces 050DCTWFLK. 050DCTBMC replaces DCTB/DCTWF, and DCTBLKMC replaces DCTBLK and DCTWFLK.

Front of Logic Board

End Panel

Button Pad

Back of Logic Board

Install new receiver logic board

33.1 Connect the wire harnesses to the

new receiver logic board. When

reconnecting the wire harness, be sure

the tabs on the wire harness are facing

the end panel, not the logic board.

3.3 Reinsert the wires.

Door control wires:

• white wire into the white terminal.

• white/red wire into the red terminal.

Safety sensor wires:

• white wires into the white terminal.

• white/black wires into the

grey terminal.

Reconnect any lock terminal wires.

NOTE: A test of the safety reverse system is necessary for safe operation.

To insert or remove the wires from

the terminal, push in the tab with a

screwdriver tip.

Programming

1.1 Press and release the Learn button on the garage door opener. The Learn indicator light will

glow steadily for 30 seconds.

1.2 Within 30 seconds, press and hold the

button on the remote control.

1.3 Release the button when the garage door

opener light blinks. It has learned the

code. If light bulbs are not installed, two

clicks will be heard.

Program a remote using the learn button

Learn

Indicator

Light

Yellow Learn

Button

3.4 Install the light lens by aligning with

the hinges and snapping into place.

Reconnect power.

NOTE: When installing the light lens, ensure the

antenna wires are hanging straight down.

Red

White

Grey

Logic Board

Wire Clip

End Panel

Wire

Harness

Tabs

3.2 Insert the antenna wires through

the holes in the end panel. Snap the

receiver logic board into place on the

end panel and fasten with screws.

NOTE: Some

models will require

the short antenna

wire to be placed in

the traps of the end

panel.

Antenna wires

Antenna

wires

To program the Wi-Fi garage door opener to your network refer to your owner’s manual.

For garage door openers without a battery

back up system: remove the button pad from

the logic board and replace it with the alternate

button pad.

NOTE: If your logic board

has a wire clip, use the

wire clip to hold wires to

the logic board.

Lock

Terminals

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	050DCTBLKMC

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 050DCTBLKMC stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster SL580 Manual

8 August 2025

LiftMaster HCT12 Manual

7 August 2025

LiftMaster MyQ 827LM Manual

7 August 2025

LiftMaster SL595 Manual

7 August 2025

LiftMaster CAPXSTK Manual

7 August 2025

LiftMaster 66LM Manual

7 August 2025

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Quantum Turbo 3 Manual

15 Oktober 2025

Stihl TSA 300.0 Manual

15 Oktober 2025

TVS Orbiter Manual

15 Oktober 2025

SilverCrest HG01696C Manual

15 Oktober 2025

HiFi ROSE RS451 Manual

15 Oktober 2025

Samsung WF-F1056V Manual

15 Oktober 2025

Gastroback MultiCook 42568 Manual

15 Oktober 2025

American DJ H2O DMX PRO IR Manual

15 Oktober 2025

Emos DCGW15 Manual

15 Oktober 2025

Gamdias Athena M4M Wood Manual

15 Oktober 2025