LiftMaster 2000 Manual

LiftMaster Ikke kategoriseret 2000

Læs gratis den danske manual til LiftMaster 2000 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om LiftMaster 2000, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

GATE HINGES

MODELS 2000 AND 2100

MODEL 3100 (ADJUSTABLE)

INSTALLATION

LiftMaster Gate Hinges are to be mounted with the yoke welded to the

gate and the body welded to post (Figure 1). The hinges must be installed

with the hinge pins in a straight line. Weld only on the vertical portions of

the yoke and plate. DO NOT weld the top and bottom of the hinges. Bolt

on versions are also available.

SHOP FABRICATION

• Locate hinges on gate frame in shop.

• Weld hinges to gate.

INSTALL – OPTION 1:

1. Place gate in desired position.

2. Tack weld in place.

3. Check gate movement, height, alignment, level and plumb.

4. Relieve weight of gate on post (block up gate).

5. Fully weld yoke to gate, then body to post.

6. Allow to cool – remove block.

7. Adjustable Hinge ONLY: Adjust yoke to desired position. Tighten bolt.

8. Lubricate hinge (do not over lubricate).

INSTALL – OPTION 2:

1. Remove yoke from hinges.

2. Place barrel on post/jamb in desired position.

3. Tack or weld in place.

4. Install gate.

5. Check gate movement, height, alignment, level and plumb.

6. Lubricate hinge (do not over lubricate).

MAINTENANCE

This gate hinge is equipped with a grease zerk for easy lubrication

(Figure 2). One pump of a high quality, multi-purpose grease every 3

months should be sufﬁ cient under normal operating conditions. More

frequent maintenance is necessary under severe operating conditions. Do

not over lubricate.

Figure 2

Overview

Figure 1

LIMITED LIFETIME WARRANTY

LiftMaster® warrants that the LiftMaster Gate Hinges shall be free from all defects in materials and workmanship for the lifetime of the original gate it is installed on, by

the original end user, under normal use and service, and when installed and maintained according to manufacturer speciﬁ cations and instructions. LiftMaster’s obligation

under this warranty is speciﬁ cally limited to repairing or replacing, at its option, any defective part during the warranty period. This warranty shall not apply to any part

which has been altered, damaged, improperly installed or maintained, or repaired by any person not expressly authorized by LiftMaster in writing to perform the repair.

The warranty will not apply to parts which have been damaged by accident or improper use, nor to non-defect damage. All other warranties, including but not limited

to any warranty of merchantability or ﬁ tness for any particular purpose, or otherwise expressed or implied, are hereby disclaimed, except as speciﬁ cally stated above.

LiftMaster shall in no event be liable either for incidental or consequential damages or for any special damages of further loss, which may arise in connection with any

claim. However, if LiftMaster is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty or otherwise, regardless of the cause

or origin, LiftMaster’s maximum liability shall not in any case exceed the purchase price of the individual product or products, refund of which shall be the complete and

exclusive remedy against LiftMaster. This warranty gives the owner speciﬁ c legal rights, and owner may have other rights, which vary from state to state. Some states do

not allow limitations or exclusions or implied warranties for incidental or consequential damages so the foregoing limitations or exclusions may not apply.

Gate

Post

Gate Post

Yoke

Body

Gate Post

Grease Zerk

Gate Post

Yoke

Body

SQUARE

ROUND