LiftMaster 375UT Manual

LiftMaster Ikke kategoriseret 375UT

Læs gratis den danske manual til LiftMaster 375UT (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om LiftMaster 375UT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

UNIVERSAL REMOTE CONTROL

MODEL 375UT

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate,

or play with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are

no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to

cross path of moving gate or door.

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

• Replace ONLY with 3V CR2032 coin batteries.

• DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are

prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause

undesired operation.

Chamberlain and LiftMaster are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door Corporation. Overhead Door is a Trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation.

Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. Wayne Dalton is a trademark of Wayne Dalton Corporation. Do It is a trademark of Do It Best Corporation.

REMOTE CONTROL BATTERY

Battery

Dispose of old batteries properly.

Replace ONLY with 3V CR2032 coin batteries.

LiftMaster.com

1-800-442-1255

PROGRAMMING

1Start with your garage door, gate, or commercial door closed.

NOTE: The SMART/LEARN button or DIP SWITCHES are located either on the product or in

an external receiver on or near the product. Consult your product owner’s manual to locate

the SMART/LEARN button or DIP SWITCHES.

NOTE: If you have a 2 position DIP SWITCH and programming fails, reverse DIP SWITCHES

(OFF to ON and ON to OFF).

Button 1

Button 2

Program Button

DIP Switches

LED

Read instructions thoroughly BEFORE beginning. If using the Universal Remote

Control with residential door openers, the Universal Remote Control must be

used only with door openers manufactured after 1993 that utilize photoelectric

sensors. The photoelectric sensors are always located on or near the bottom of

the door track.

The Universal Remote Control can be programmed to activate up to two

products, such as a garage door opener, gate operator, or commercial door operator. Each button

on the Universal Remote Control works independently of the other and must be programmed

separately. The second button on the Universal Remote Control can be programmed to different

products without affecting the first button programmed. The images throughout this manual are

for reference only and your product may look different.

3Press and release the SMART/LEARN button on your product.

Match the remote control DIP SWITCHES to the existing receiver or existing remote control.

4 Press and release the button. When the LED stops flashing, continue to press and

release the button until a click is heard from the garage door opener, a light on

the garage door opener blinks, the garage door opens/closes, or a beep is heard

from the gate operator (maximum 18 times).

Press and release the Universal Remote Control button…

... 8 times Chamberlain®* Yellow Button 2011-Current

... 3 times Chamberlain®* Purple Button 2005-Current

... 2 times Chamberlain®* Orange Button 1997-2005

... 4 times Chamberlain®* Green Button 1993-1996

... 6 times Genie Overhead Door® Intellicode 1995-Current

... 5 times Genie Overhead Door® Intellicode 2005-Current

... 1 time Linear® Mega-Code 1997-Current

... 7 times Stanely® Security Code 1998

... 9 times Wayne Dalton® Rolling Code 372.5 MHz

1999-Current

... 14 times Linear Multicode® 10 Position Dip Switch

... 16 times Stanley Multicode® 10 Position Dip Switch

... 18 times Linear ® 8 Position Dip Switch

The LED on the Universal Remote Control MUST stop blinking between each press of

the button. The code is accepted when a click or beep is heard, a light blinks, or the

door/gate activates.

* LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are

compatible with Chamberlain technology.

5Press the program button to exit programming mode.

Programming is now complete.

6 Press the programmed button to activate your product. If

product does not activate, repeat the programming steps

3-6 again.

STOP

LEARN

XMITTER

CONTROL BOARD

RADIO

BUTTON

LOGIC BOARD

SLOT 1

RADIO

SLS

MRT MID T TC

RELAY A

RELAY B

TIMER

ENABLE

123

FSTS

DIAG

OPTN

PROG

T TS

CLS

OLS

MID

REV

STD

SLOT 2

MOTO R

DIRECTIO N

3-PHASE

1-PHASE

SMART/LEARN

BUTTON

RECEIVER REMOTEDIP SWITCHES

2 Open the remote control by sliding the battery cover down. Press and hold the program

button until the LED lights (approximately 2 seconds).

Program

Button

LED

Cover

Program Button

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information

go to www.P65Warnings.ca.gov