LiftMaster 64LM Manual

LiftMaster Ikke kategoriseret 64LM

Læs gratis den danske manual til LiftMaster 64LM (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5 anmeldelser. Har du et spørgsmål om LiftMaster 64LM, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
To prevent possible SERIOUS INJURY or
DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of
reach of children. NEVER permit children
to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be
seen clearly, is properly adjusted, and
there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight
until completely closed. NEVER permit
anyone to cross path of moving gate or
door.
INTRODUCTION
This product is for use with gate operators, commercial door operators and any LiftMaster
® product
that uses a 390 MHz fixed code. The single-button remote control will activate one device, the
2-button remote control will activate up to 2 devices, and the 3-button remote control will activate
up to 3 devices.
Models 61LM & 61LMC
Models 62LM & 62LMC
Models 33LM, 33LMC
63LM, & 63LMC
Models 64LM & 64LMC
Locate the dip switches on your remote control
BEFORE YOU BEGIN
Single-Button and 3-Button Remote Controls:
Slide the battery cover open to access the dip
switches in the remote control.
2-Button Remote Control:
The 2-button remote control has two sets of
dip switches.
Slide the battery cover open to access the dip
switches for the smooth button. Remove the
screw on the back of the remote control and
remove the cover by pressing the tab. This will
access the dip switches for the ribbed button.
3-Button Mini Remote Control:
The large top button is recommended for use with
a garage door opener and/or light control product.
The other push buttons can be used to operate
another garage door opener and/or light control
product.
Access the dip switches by turning the remote
over and removing the back of the case. Be
careful to avoid moving circuit board components.
+
0
–
123456789
+
0
–
123456789
+
0
–
123456789
+
0
–
123456789
Tab
1
Single and 3-Button Remote Controls
2-Button Remote Controls
Mini Remote Controls
WARNING: This product can expose you to chemicals including lead, which are known to
the State of California to cause cancer or birth defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov
PROGRAMMING
1
1
Press and release the Smart/Learn button
on your product. The LED will light.
2
2
Within 30 seconds press and hold the
button on the remote control that you
wish to activate your product.
Programming is complete.
Repeat the steps above for each button and/or
remote control you would like to program.
Programming with Smart/Learn button
2
Programming the remote control to an
existing remote control
Locate the dip switches in the new and old
remote controls. Place remote controls side by
side and set the dip switches in the remote
controls to matching positions (+,0,-).
Programming a 3-button remote control
When programming a single or 2-button remote
control to a 3-button remote control it is very
important to set dip switch #1 to the correct
position. The dip switch in the single or 2-button
remote control MUST correspond to the buttons
on the 3-button remote control as shown.
Example: If you are programming a
single-button remote control to the middle button
on the 3-button remote control, dip switch #1 in
the single-button remote control MUST be set to
“0” in order for both buttons to work.
+
0
–
1 2 3 4 5 6 7 8 9
+
0
–
1 2 3 4 5 6 7 8 9
=
+
0
–
1 2 3 4 5 6 7 8 9
+
0
–
123 456 789
=
2 3 4 5 6 7 8 9
+
0
–
1 2 3 4 5 6 7 8 9
=
+
0
–
1
+0
-
New Remote Control
Dip Switch Settings
From Product
3-Button
Remote Control
Single or 2-Button
Remote Control
Dip switch #1 must
correspond to the 3-button
remote control buttons
Existing Remote Control
New Remote
Control
12
Smart/Learn Button
Programming the remote control
without an existing remote control
Set the dip switches in the remote controls to
any position you want (+,0,-).
+
0
–
1 2 3 4 5 6 7 8 9
New Remote Control
Use a pen or screwdriver to slide the dip switches.
Check the dip switch settings on the back of
your product.
Use a pen or screwdriver to slide the dip
switches in the remote control to match the
dip switches on the back of the product.
When the dip switches have been set press the remote
control button to activate your product.
Programming with dip switches

Produkt Specifikationer

Mærke: LiftMaster
Kategori: Ikke kategoriseret
Model: 64LM

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 64LM stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret LiftMaster Manualer

LiftMaster

LiftMaster 041-0405-000 Manual

15 Juni 2025
LiftMaster

LiftMaster LMHNTG Manual

4 September 2024
LiftMaster

LiftMaster CAPXSTKPL Manual

3 September 2024
LiftMaster

LiftMaster BG790 Manual

3 September 2024
LiftMaster

LiftMaster 64LM Manual

3 September 2024
LiftMaster

LiftMaster CAPXSHOOD Manual

28 August 2024
LiftMaster

LiftMaster myQ-SGC2WCH Manual

21 August 2024
LiftMaster

LiftMaster CAPXS Manual

21 August 2024
LiftMaster

LiftMaster MGJ5011U Manual

21 August 2024
LiftMaster

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Festo

Festo DFM-32-100-B-PPV-A-KF Manual

17 Juni 2025
Playtive

Playtive IAN 285777 Manual

17 Juni 2025
Festo

Festo VAEM-L1-S-M3-26 Manual

17 Juni 2025
Festo

Festo DFPC-320 Manual

17 Juni 2025
EFX

EFX ICAK12 Manual

17 Juni 2025
Bearware

Bearware 307294 Manual

17 Juni 2025
Futaba

Futaba MC-9200H/A Manual

17 Juni 2025
Hansgrohe

Hansgrohe AXOR Montreux 16517800 Manual

17 Juni 2025
OmniMount

OmniMount 2N1-S Manual

17 Juni 2025
Festo

Festo DSNU-S-12- -F1A Manual

17 Juni 2025