LiftMaster 860LM Manual

LiftMaster Ikke kategoriseret 860LM

Læs gratis den danske manual til LiftMaster 860LM (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7 anmeldelser. Har du et spørgsmål om LiftMaster 860LM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is NOT connected BEFORE installing the receiver.

To prevent possible SERIOUS INJURY or DEATH from a moving gate

or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER

permit children to operate, or play with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed.

NEVER permit anyone to cross path of moving gate or door.

To prevent possible SERIOUS INJURY or DEATH, the use of

CONSTANT OPERATION on residential openers is PROHIBITED.

When a receiver is used to activate a commercial door opener, a

reversing edge MUST be installed on the bottom of the door. Failure to

install a reversing edge under these circumstances may result in

SERIOUS INJURY or DEATH to persons trapped beneath the door.

WEATHER RESISTANT UNIVERSAL RECEIVER

MODEL 860LM

APPLICATION

The receiver can be used as a single, two, or three channel receiver to

control up to 3 gates or commercial door operators. The receiver can also

be used with a 3-button remote control to operate the OPEN, CLOSE, and

STOP feature on a commercial door operator. The 860LM Weather

Resistant Universal Receiver may be mounted in outside locations that

may be exposed to rain or moisture. This receiver is not compatible with

MyQ® enabled garage door openers or devices.

INSTALLATION

The receiver and antenna use TV Type F coaxial connectors. The antenna

can be connected directly to the receiver or it can be installed remotely

using a coaxial cable extension kit Model 86LM or 86LMT.

1. Select a location for the receiver which allows access to the terminals

and space for the antenna. Ensure antenna does not touch metal

surfaces. DO NOT bend or fold the antenna.

2. Attach the receiver bracket to the mounting surface with hardware (not

provided). Snap the receiver onto the bracket and secure the receiver

to the bracket with the #8 screws provided.

3. After the installation is complete, remove the cover. Connect power to

the receiver with a 95LM wired-in transformer, or you may connect to

the power going to the operator (see power ratings on next page).

WIRING

Below are wiring examples. Refer to your commercial door operator or

gate operator owner's manual or wiring diagrams for specific wiring

information.

SINGLE CHANNEL

Receiver

Single Operator(s)

TWO & THREE CHANNEL

Receiver

Operator 1

Operator 2

Operator 3

OPEN/CLOSE/STOP

Receiver

Single Operator

3-Button Control Device

Refer to your commercial

door operator or gate

operator wiring diagrams

for instructions on

connecting two or more

3-Button control devices.

SPECIFICATIONS

Contact Rating . . . . . . . . . . . . . . . . . . . . . . 5 Amps 28 Vac or dc Max.

Power Rating . . . . . . . . . . . . . . . .9-30V AC or 9-34V DC, 50mA, 60Hz

RF Frequency . . . . . . . . . . . . . . . . . . . . . . . . . .310, 315, and 390 MHz

NOTE: If your operator does not meet the power specifications you

will need a Model 95LM transformer.

COMPATIBLE ACCESSORIES

Remote Controls . . . . . . . . . . Models 811LM, 813LM, 891LM, 893LM,

890MAX, 893MAX, 895MAX, 892LT, 894LT

Keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Models 877LM, 877MAX

Wireless Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 885LM

Antenna Extension Kits

15' Extension Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 86LM

25' Extension Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 86LMT

Antenna Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K77-36541

Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95LM

FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:

1-800-528-2806

NOTICE: To comply with FCC and/or Industry Canada (IC) rules. adjustment or modifications of this

receiver are prohibited. THERE ARE NO USER SERVICEABLE PARTS.

This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

PROGRAMMING

Each channel is compatible with a certain number of remote controls and

keypads. Refer to the list below:

• CH1: 50 remote controls and 2 keypads

• CH2: 20 remote controls and 2 keypads

• CH3: 20 remote controls and 2 keypads

When the channel has reached full capacity for remote controls, all LEDs

will blink 3 times. When the channel has reached full capacity for

keypads, all LEDs will blink 4 times. Additional accessories can be

programmed, however, the newly programmed accessory will replace the

first programmed accessory.

NOTE: This receiver will only allow you to program a button on the

remote control to one channel at a time. For example, if the button on the

remote control is already programmed to channel 1 and then is

programmed to channel 3, the button will be erased from channel 1 and

will only work on channel 3.

PROGRAM A SINGLE BUTTON REMOTE CONTROL

1. Press and release the Learn button for the selected channel on the

receiver. The corresponding LED will glow steadily for 30 seconds.

2. Within 30 seconds press and hold the button on the remote control

that you wish to program to the receiver.

3. Release the remote control button when the LED on the receiver

blinks, then turns off. Programming is complete.

Repeat the steps above for each remote control you would like to

program.

PROGRAM A 3-BUTTON REMOTE CONTROL AS OPEN, CLOSE,

AND STOP

1. Press and release the CH1 Learn button on the receiver.

2. Within 30 seconds press the desired OPEN button on the remote

control.

3. Press and release the CH2 Learn button on the receiver.

4. Within 30 seconds press the desired CLOSE button on the remote

control.

5. Press and release the CH3 Learn button on the receiver.

6. Within 30 seconds press the desired STOP button on the remote

control.

NOTE: If a remote control button is not pressed within 30 seconds, the

LED next to the selected Learn button will turn OFF. In that case, repeat

the programming.

TO ERASE THE MEMORY

Press and hold the Learn button for the channel you want to erase.

Release the button when the corresponding LED turns off; the memory

has been erased.

CH1 Learn Button

CH2 Learn Button

CH3 Learn Button

NOTE: The receiver can command the operator to close the door or gate

by constant pressure. This feature is only available with a wireless

control panel (Model 885LM). To enable this feature, press and hold the

push bar until the gate or door moves to the closed position.

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	860LM

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 860LM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

LiftMaster 64LM Manual

3 September 2024

LiftMaster CAPXSHOOD Manual

28 August 2024

LiftMaster myQ-SGC2WCH Manual

21 August 2024

LiftMaster CAPXS Manual

21 August 2024

LiftMaster MGJ5011U Manual

21 August 2024

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tracer Ambience - Smart Circle Manual

17 Juni 2025

Ulsonix ULX-480-1 Manual

17 Juni 2025

JUNG CD 104.18 WU Manual

17 Juni 2025

Hughes & Kettner TriAmp MKII Manual

17 Juni 2025

Cecotec Bean&Clean Manual

17 Juni 2025

Steinberg SBS-FZ 3000/3BM Manual

17 Juni 2025

Mars Gaming MPB1000SI Manual

17 Juni 2025

Stamos SWS05 Manual

17 Juni 2025

Royal Catering RCAT-140/80 Manual

17 Juni 2025

Planet Audio P90CPAP Manual

17 Juni 2025