LiftMaster 882LMW Manual

LiftMaster Ikke kategoriseret 882LMW

Læs gratis den danske manual til LiftMaster 882LMW (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 15 anmeldelser. Har du et spørgsmål om LiftMaster 882LMW, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
INSTALLATION
To insert or release
wire, push in tab with
screwdriver tip.
7/16"
(11 mm)
7/16"
(11 mm)
5 feet (1.5 m)
minimum
GANG BOX
DRYWALL
6ABx1-1/4" Drywall Anchors
6-32x1"
PROGRAM
13
Unplug the garage door opener. Disconnect the battery (if applicable).
1. Connect the wires to the back of the door control.
2. Secure the door control to the wall.
3. Connect the wires to the garage door opener.
Plug in the garage door opener and reconnect the battery. The command LED on the
door control will blink if installed correctly. To synchronize the garage door opener and
the door control, press the push bar up to 3 times, until the garage door opener
activates.
RED
WHITE
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is NOT connected BEFORE installing door
control.
• Connect ONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing
garage door:
• Install door control within sight of garage door, out of reach of
children at a minimum height of 5 feet (1.5 m), and away from
ALL moving parts of door.
• NEVER permit children to operate or play with door control
push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed.
NEVER permit anyone to cross path of closing garage door.
• Unattended devices and features are to be used ONLY with
sectional doors.
MULTI-FUNCTION CONTROL PANEL
(SECURITY+ 2.0®) MODEL 882LMW
AND
PREMIUM MOTION-DETECTING
CONTROL PANEL MODELS 881LMW AND 886LMW
For use with Security+ 2.0® Garage Door Openers, Wi-Fi® enabled
Security+ 2.0® Garage Door Openers (indicated by the Wi-Fi logo on
the garage door opener cover) and MyQ® accessories.
UNATTENDED OPERATION
The Timer-to-Close (TTC) feature, the MyQ
® Smartphone Control app,
and MyQ® Garage Door and Gate Monitor are examples of unattended
close and are to be used ONLY with sectional doors. Any device or
feature that allows the door to close without being in the line of sight
of the door is considered unattended close. The Timer-to-Close (TTC)
feature, the MyQ® Smartphone Control, and any other MyQ® devices
are to be used ONLY with sectional doors.
2
Model 882LMW
Models 881LMW and 886LMW
REMOTE CONTROL
1. Press the LEARN button on the
door control . The twice
Command LED will blink.
2. Press and release the button on
the remote control that you wish
to operate your garage door.
The garage door opener lights will
flash (or two clicks will be heard)
and the Command LED will stop
blinking when the code has been
programmed.
PIN
? ? ? ?
KEYLESS ENTRY
1. Press the LEARN button on the door
control twice. The Command LED will
blink.
2. Enter a 4-digit personal identification
number (PIN) on the keypad. Then
press the ENTER button.
The garage door opener lights will flash (or
two clicks will be heard) and the Command
LED will stop blinking when the code has
been programmed.
1. Lift the push bar on the door control. Press and release the LEARN
button. The garage door opener will beep once and the command LED
on the door control will blink to indicate Wi-Fi learn mode. You have 20
minutes to complete the connection process.
2. On your mobile device, go to Settings > Wi-Fi and select the network
with the “MyQ-” prefi x.
3. Launch the web browser on your smartphone or tablet. Enter setup.myqdevice.com
into the browser address bar. Follow the on screen prompts to connect the garage
door opener to your Wi-Fi network. The MyQ serial number will display on screen.
Write the serial number in the space below.
4. Download the MyQ app from the App Store® or Google Play™ store. Sign up for your
MyQ account and add the MyQ serial number to your account.
If you are unsuccessful adding your device, try an alternate web browser or visit
WiFiHelp.LiftMaster.com.
CONNECT YOUR GARAGE DOOR OPENER TO YOUR HOME WI-FI®
NETWORK
(for Wi-Fi garage door openers ONLY)
Command LED
Command LED
Model
882LMW
Models 881LMW
and 886LMW
WARNING: This product can expose you to chemicals
including lead, which are known to the State of California to
cause cancer or birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov
LOCK
Prevents activation of the garage door opener from remote controls while still
allowing activation from the door control and keyless entry. Factory default is
OFF.
Turn ON: Press and hold the LOCK button for 2 seconds. The command
LED will blink as long as the lock feature is activated.
Turn OFF: Press and hold the LOCK button again for 2 seconds. The
command LED will stop flashing and normal operation will resume.
LIGHT
Press the LIGHT button to turn the garage door opener lights on or off. The
LIGHT button will not control the lights when the door is in motion. When the
lights are turned on they will stay on until the LIGHT button is pressed again,
or until the garage door opener is activated. Once the garage door opener is
activated the lights will turn off after a specified period of time (see below).
TO CHANGE THE AMOUNT OF TIME THE GARAGE DOOR OPENER LIGHTS
WILL STAY ON
Press and hold the LOCK button until the garage door opener lights flash
(about 10 seconds). The garage door opener lights will flash up to 4 times to
indicate current setting:
1 Flash = Lights stay on 1 ½ minutes
2 Flashes = Lights stay on 2 ½ minutes
3 Flashes = Lights stay on 3 ½ minutes
4 Flashes = Lights stay on 4 ½ minutes (factory default)
Repeat the steps above until your desired time frame is reached.
LIGHT FEATURE FOR THE SAFETY REVERSING SENSORS
The garage door opener lights will turn on when the safety reversing sensor
beam is interrupted. Factory default is ON.
Turn ON: Start with the garage door opener lights on. Press and hold the
LIGHT button to turn off the light, continue to hold until the light turns on
(about 10 seconds).
Turn OFF: Start with the garage door opener lights off. Press and hold the
LIGHT button to turn on the light, continue to hold until the light turns off
(about 10 seconds).
FEATURES
TIMER-TO-CLOSE (TTC)
(for model 881LMW ONLY)
DO NOT enable TTC if operating a one-piece door. TTC is to be used ONLY
with sectional doors.
The TTC can be set to automatically close your garage door after a specified
period of time (1, 5, or 10 minute intervals). Once the TTC has been set and
the door is open, the selected close interval will blink and begin to count
down to close the door. The garage door opener will beep and the lights will
fl ash before closing the door.
This feature is NOT intended to be the primary method of closing the door. A
keyless entry should be installed in the event of an accidental lock out
when using this feature.
Turn ON: Press and hold the ON button until one of the TTC LEDs light up.
Change the TTC Time Intervals: Press the ON button a second time to
cycle through the time interval options (the corresponding TTC LED will
light for each time interval). The garage door opener light bulbs will blink
as confirmation.
Temporarily suspend the TTC: Press and release the HOLD OPEN button.
Press and release the HOLD OPEN button again to resume normal TTC
operation.
Turn OFF: Press and hold the OFF button until all TTC LEDs turn off and a
beep is heard from the garage door opener.
The TTC WILL NOT work under the following conditions:
• If the door encounters an obstruction while closing, the garage door
opener will make a second attempt to close the door. If the obstruction
has not been cleared after the second attempt, the garage door opener will
reverse open, stop and WILL NOT close until the obstruction has been
cleared.
• If the safety reversing sensors are incorrectly installed or misaligned the
garage door will reverse open and WILL NOT close until the safety
reversing sensors are correctly installed and aligned. When the safety
reversing sensors have been aligned, the door will close when the garage
door opener is activated.
• If the garage door opener is operating by battery power the TTC will not
work.
NOTE: If you have an 880LMW installed and the TTC is set to a custom time,
the 3 LED's on the 881LMW will blink. If the 3 LED's are blinking and you
have an 881LMW ONLY, press the ON button to set the time properly.
MOTION SENSOR
(for models 881LMW and 886LMW ONLY)
The motion sensor will automatically turn on the garage door opener lights
when motion is detected. The lights will come on for the set period of time,
then shut off. The factory default is on for 4-1/2 minutes.
Turn ON/OFF: Slide the motion sensor switch ON or OFF.
MAINTENANCE ALERT SYSTEM (MAS)
When the garage door opener needs to be serviced (approximately 4500
garage door opener cycles) the command and service LEDs will alternately
blink back and forth. Factory default is OFF.
Turn ON/OFF: Press and hold the LEARN button. Then press the LIGHT
button. The service LED will blink the status; ON is 2 blinks and OFF is 3
blinks.
LEARN Button
LIGHT Button
Service LED
(red)
LOCK Button
Press the push bar to
open or close the door.
Motion Sensor
Motion Sensor
Switch
TTC LEDs
(1, 5, 10 Minutes)
(Model 881LMW
only)
1 5 10
MODELS 881LMW AND 886LMW
MODEL 882LMW
LEARN Button
LIGHT Button
Service LED
(red)
LOCK Button
Command LED
(yellow)
Press the push bar to open or
close the door.
Command LED
(yellow)
ON Button
(Model 881LMW
only)
OFF Button
(Model 881LMW
only)
HOLD OPEN
(Model 881LMW
only)
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifi cations of this receiver
and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE
NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or offi ce use. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
ONE YEAR LIMITED WARRANTY
LiftMaster warrants to the first consumer purchaser of this product that it
is free from defect in materials and/or workmanship for a period of 1 year
from the date of purchase.

Produkt Specifikationer

Mærke: LiftMaster
Kategori: Ikke kategoriseret
Model: 882LMW

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 882LMW stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret LiftMaster Manualer

LiftMaster

LiftMaster 041-0405-000 Manual

15 Juni 2025
LiftMaster

LiftMaster LMHNTG Manual

4 September 2024
LiftMaster

LiftMaster CAPXSTKPL Manual

3 September 2024
LiftMaster

LiftMaster BG790 Manual

3 September 2024
LiftMaster

LiftMaster 64LM Manual

3 September 2024
LiftMaster

LiftMaster CAPXSHOOD Manual

28 August 2024
LiftMaster

LiftMaster myQ-SGC2WCH Manual

21 August 2024
LiftMaster

LiftMaster CAPXS Manual

21 August 2024
LiftMaster

LiftMaster MGJ5011U Manual

21 August 2024
LiftMaster

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Grundig

Grundig GIEI827578PN Manual

1 August 2025
Finlux

Finlux FC-550mmW Manual

1 August 2025
Thermaltake

Thermaltake Toughpower PF3 Platinum Manual

1 August 2025
Olivetti

Olivetti d-Copia 4524MFplus Manual

1 August 2025
Grundig

Grundig GEBD19401BPH Manual

1 August 2025
Thermaltake

Thermaltake Max 3504 Manual

1 August 2025
Tripp Lite

Tripp Lite N286-100G-SR4SA Manual

1 August 2025
Tripp Lite

Tripp Lite Protect It! TLP88USBB Manual

1 August 2025
Tripp Lite

Tripp Lite Protect It! TLP664USBB Manual

1 August 2025
Silver Cross

Silver Cross Tide Manual

1 August 2025