LiftMaster 886LM Manual

LiftMaster Ikke kategoriseret 886LM

Læs gratis den danske manual til LiftMaster 886LM (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om LiftMaster 886LM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

LIGHT

HOLD

OPEN

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is NOT connected BEFORE installing door control.

• Connect ONLY to 12 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

• Install door control within sight of garage door, out of reach of children at a minimum

height of 5 feet (1.5 m), and away from ALL moving parts of door.

• NEVER permit children to operate or play with door control push buttons or remote control

transmitters.

• Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no

obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross

path of closing garage door.

PREMIUM MOTION-DETECTING CONTROL PANEL

Models 881LM and 886LM

Feature Overview

TIMER-TO-CLOSE (TTC) FOR MODEL 881LM ONLY

DO NOT enable TTC if operating a one-piece door. TTC is to be used ONLY with sectional doors.

The TTC can be set to automatically close your garage door after a specified period of time (1, 5,

or 10 minute intervals). The garage door opener will beep and the lights will ﬂ ash before closing

the door. If the door encounters an obstruction while closing, the garage door opener will make a

second attempt to close the door. If the obstruction has not been cleared after the second attempt,

the garage door opener will reverse open, stop and WILL NOT close until the obstruction has been

cleared. TTC WILL NOT work if the garage door opener is operating by battery power or if the

safety reversing sensors are misaligned. This feature is NOT intended to be the primary method of

closing the door. A keyless entry should be installed in the event of an accidental lock out when

using this feature.

Premium Motion-Detecting

Control Panel

Safety Reversing

Sensors

Yellow

LEARN Button

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modiﬁ cations of this receiver and/or transmitter are

prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards for Home or ofﬁ ce use. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

For use with Security 2.0TM Garage Door Openers. All Security 2.0TM Garage Door Openers have

a yellow Learn button and two yellow antennas. The features are adjustable and may be turned off

or on as desired. Refer to the Feature Settings section.

MOTION SENSOR

The motion sensor will automatically turn on the garage door opener lights when motion is

detected. The lights will come on for the set period of time, then shut off. The factory setting is on

and set at 4-1/2 minutes.

MAINTENANCE ALERT SYSTEM (MAS)

This feature assists the homeowner in ensuring the garage door opener system stays in good

working condition. The MAS feature MUST be activated at time of installation. The factory setting

is off. The service LED will come on after 4500 garage door opener cycles. This indicates the

garage door opener may need maintenance; contact your installation dealer. If the MAS feature is

activated, the command LED (yellow) and the service LED (red) will alternate flashing back and

forth.

LIGHT BUTTON

Press the LIGHT button to turn the garage door opener lights on or off. When the lights are turned

on they will stay on until the LIGHT button is pressed again, or until the garage door opener is

activated. Once the garage door opener is activated the lights will turn off after the specified period

of time (the factory setting is 4-1/2 minutes). The LIGHT button will not control the lights when the

door is in motion.

LOCK

The LOCK feature is designed to prevent activation of the garage door opener from remote controls

while still allowing activation from the door control and keyless entry. This feature is useful for

added peace of mind when the home is empty (i.e. vacation).

RED

WHITE

GREY

Installation

Install the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small

children cannot reach, and away from the moving parts of the door. For gang box installations it is

not necessary to drill holes or install the drywall anchors. Use the existing holes in the gang box.

NOTE: Pre-wiring means that your garage already has wires installed for the door control.

WIRE THE DOOR CONTROL

7/16" (11 mm)

Unplug the garage door opener to

ensure the door control cannot be

activated during wiring.

Strip 7/16" (11 mm) of insulation from

one end of the wire and separate the

wires.

Connect the wire to both screws on the

back of the door control. The wires can

be connected to either screw.

PRE-WIRED INSTALLATIONS: Choose any two

wires to connect, but make note of which wires

are used.

MOUNT THE DOOR CONTROL

Mark the location of the bottom

mounting hole and drill a 5/32" (4 mm)

hole.

Install the bottom screw, allowing

1/8" (3 mm) to protrude from the wall

Position the bottom hole of the door

control over the screw and slide down

into place.

Lift the push bar up and mark the top

hole.

Remove the door control from the wall

and drill a 5/32" (4 mm) hole for the

top screw.

Position the bottom hole of the door

control over the screw and slide down

into place. Attach the top screw.

WIRE TO GARAGE DOOR OPENER

Strip 7/16" (11 mm) of insulation from

the end of the wire near the garage door

opener.

Connect the wire to the red and white

terminals on the garage door opener.

The wires can be connected to either

terminal.

Reconnect power to the garage door

opener. The command LED behind the

push bar on the door control will blink

if installed correctly. To synchronize

the garage door opener and the door

control, press the push bar up to

3 times. Press until the garage door

opener activates.

PRE-WIRED INSTALLATIONS: Connect the same

wires to the garage door opener that were

previously connected to the door control.

To insert or release wire, push

in tab with screwdriver tip.

GANG BOXDRYWALL

6ABx1-1/4" Drywall Anchors 6-32x1"

HARDWARE

- Wall -

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	886LM

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 886LM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster SL580 Manual

8 August 2025

LiftMaster HCT12 Manual

7 August 2025

LiftMaster MyQ 827LM Manual

7 August 2025

LiftMaster SL595 Manual

7 August 2025

LiftMaster CAPXSTK Manual

7 August 2025

LiftMaster 66LM Manual

7 August 2025

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JILONG JL097205NPF Manual

14 September 2025

Brandson 306570 Manual

14 September 2025

Nedis PIM30012EGY Manual

14 September 2025

Neutrik SCD-W Manual

14 September 2025

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025