LiftMaster 886LMW Manual

LiftMaster Ikke kategoriseret 886LMW

Læs gratis den danske manual til LiftMaster 886LMW (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 4 anmeldelser. Har du et spørgsmål om LiftMaster 886LMW, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTALLATION

To insert or release

wire, push in tab with

screwdriver tip.

7/16"

(11 mm)

7/16"

(11 mm)

5 feet (1.5 m)

minimum

GANG BOX

DRYWALL

6ABx1-1/4" Drywall Anchors

6-32x1"

PROGRAM

Unplug the garage door opener. Disconnect the battery (if applicable).

1. Connect the wires to the back of the door control.

2. Secure the door control to the wall.

3. Connect the wires to the garage door opener.

Plug in the garage door opener and reconnect the battery. The command LED on the

door control will blink if installed correctly. To synchronize the garage door opener and

the door control, press the push bar up to 3 times, until the garage door opener

activates.

RED

WHITE

To prevent possible SERIOUS INJURY or DEATH from

electrocution:

• Be sure power is NOT connected BEFORE installing door

control.

• Connect ONLY to 12 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing

garage door:

• Install door control within sight of garage door, out of reach of

children at a minimum height of 5 feet (1.5 m), and away from

ALL moving parts of door.

• NEVER permit children to operate or play with door control

push buttons or remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed.

NEVER permit anyone to cross path of closing garage door.

• Unattended devices and features are to be used ONLY with

sectional doors.

MULTI-FUNCTION CONTROL PANEL

(SECURITY+ 2.0®) MODEL 882LMW

AND

PREMIUM MOTION-DETECTING

CONTROL PANEL MODELS 881LMW AND 886LMW

For use with Security+ 2.0® Garage Door Openers, Wi-Fi® enabled

Security+ 2.0® Garage Door Openers (indicated by the Wi-Fi logo on

the garage door opener cover) and MyQ® accessories.

UNATTENDED OPERATION

The Timer-to-Close (TTC) feature, the MyQ

® Smartphone Control app,

and MyQ® Garage Door and Gate Monitor are examples of unattended

close and are to be used ONLY with sectional doors. Any device or

feature that allows the door to close without being in the line of sight

of the door is considered unattended close. The Timer-to-Close (TTC)

feature, the MyQ® Smartphone Control, and any other MyQ® devices

are to be used ONLY with sectional doors.

Model 882LMW

Models 881LMW and 886LMW

REMOTE CONTROL

1. Press the LEARN button on the

door control . The twice

Command LED will blink.

2. Press and release the button on

the remote control that you wish

to operate your garage door.

The garage door opener lights will

flash (or two clicks will be heard)

and the Command LED will stop

blinking when the code has been

programmed.

? ? ? ?

KEYLESS ENTRY

1. Press the LEARN button on the door

control twice. The Command LED will

blink.

2. Enter a 4-digit personal identification

number (PIN) on the keypad. Then

press the ENTER button.

The garage door opener lights will flash (or

two clicks will be heard) and the Command

LED will stop blinking when the code has

been programmed.

1. Lift the push bar on the door control. Press and release the LEARN

button. The garage door opener will beep once and the command LED

on the door control will blink to indicate Wi-Fi learn mode. You have 20

minutes to complete the connection process.

2. On your mobile device, go to Settings > Wi-Fi and select the network

with the “MyQ-” preﬁ x.

3. Launch the web browser on your smartphone or tablet. Enter setup.myqdevice.com

into the browser address bar. Follow the on screen prompts to connect the garage

door opener to your Wi-Fi network. The MyQ serial number will display on screen.

Write the serial number in the space below.

4. Download the MyQ app from the App Store® or Google Play™ store. Sign up for your

MyQ account and add the MyQ serial number to your account.

If you are unsuccessful adding your device, try an alternate web browser or visit

WiFiHelp.LiftMaster.com.

CONNECT YOUR GARAGE DOOR OPENER TO YOUR HOME WI-FI®

NETWORK

(for Wi-Fi garage door openers ONLY)

Command LED

Model

882LMW

Models 881LMW

and 886LMW

WARNING: This product can expose you to chemicals

including lead, which are known to the State of California to

cause cancer or birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

LOCK

Prevents activation of the garage door opener from remote controls while still

allowing activation from the door control and keyless entry. Factory default is

OFF.

Turn ON: Press and hold the LOCK button for 2 seconds. The command

LED will blink as long as the lock feature is activated.

Turn OFF: Press and hold the LOCK button again for 2 seconds. The

command LED will stop flashing and normal operation will resume.

LIGHT

Press the LIGHT button to turn the garage door opener lights on or off. The

LIGHT button will not control the lights when the door is in motion. When the

lights are turned on they will stay on until the LIGHT button is pressed again,

or until the garage door opener is activated. Once the garage door opener is

activated the lights will turn off after a specified period of time (see below).

TO CHANGE THE AMOUNT OF TIME THE GARAGE DOOR OPENER LIGHTS

WILL STAY ON

Press and hold the LOCK button until the garage door opener lights flash

(about 10 seconds). The garage door opener lights will flash up to 4 times to

indicate current setting:

1 Flash = Lights stay on 1 ½ minutes

2 Flashes = Lights stay on 2 ½ minutes

3 Flashes = Lights stay on 3 ½ minutes

4 Flashes = Lights stay on 4 ½ minutes (factory default)

Repeat the steps above until your desired time frame is reached.

LIGHT FEATURE FOR THE SAFETY REVERSING SENSORS

The garage door opener lights will turn on when the safety reversing sensor

beam is interrupted. Factory default is ON.

Turn ON: Start with the garage door opener lights on. Press and hold the

LIGHT button to turn off the light, continue to hold until the light turns on

(about 10 seconds).

Turn OFF: Start with the garage door opener lights off. Press and hold the

LIGHT button to turn on the light, continue to hold until the light turns off

(about 10 seconds).

FEATURES

TIMER-TO-CLOSE (TTC)

(for model 881LMW ONLY)

DO NOT enable TTC if operating a one-piece door. TTC is to be used ONLY

with sectional doors.

The TTC can be set to automatically close your garage door after a specified

period of time (1, 5, or 10 minute intervals). Once the TTC has been set and

the door is open, the selected close interval will blink and begin to count

down to close the door. The garage door opener will beep and the lights will

ﬂ ash before closing the door.

This feature is NOT intended to be the primary method of closing the door. A

keyless entry should be installed in the event of an accidental lock out

when using this feature.

Turn ON: Press and hold the ON button until one of the TTC LEDs light up.

Change the TTC Time Intervals: Press the ON button a second time to

cycle through the time interval options (the corresponding TTC LED will

light for each time interval). The garage door opener light bulbs will blink

as confirmation.

Temporarily suspend the TTC: Press and release the HOLD OPEN button.

Press and release the HOLD OPEN button again to resume normal TTC

operation.

Turn OFF: Press and hold the OFF button until all TTC LEDs turn off and a

beep is heard from the garage door opener.

The TTC WILL NOT work under the following conditions:

• If the door encounters an obstruction while closing, the garage door

opener will make a second attempt to close the door. If the obstruction

has not been cleared after the second attempt, the garage door opener will

reverse open, stop and WILL NOT close until the obstruction has been

cleared.

• If the safety reversing sensors are incorrectly installed or misaligned the

garage door will reverse open and WILL NOT close until the safety

reversing sensors are correctly installed and aligned. When the safety

reversing sensors have been aligned, the door will close when the garage

door opener is activated.

• If the garage door opener is operating by battery power the TTC will not

work.

NOTE: If you have an 880LMW installed and the TTC is set to a custom time,

the 3 LED's on the 881LMW will blink. If the 3 LED's are blinking and you

have an 881LMW ONLY, press the ON button to set the time properly.

MOTION SENSOR

(for models 881LMW and 886LMW ONLY)

The motion sensor will automatically turn on the garage door opener lights

when motion is detected. The lights will come on for the set period of time,

then shut off. The factory default is on for 4-1/2 minutes.

Turn ON/OFF: Slide the motion sensor switch ON or OFF.

MAINTENANCE ALERT SYSTEM (MAS)

When the garage door opener needs to be serviced (approximately 4500

garage door opener cycles) the command and service LEDs will alternately

blink back and forth. Factory default is OFF.

Turn ON/OFF: Press and hold the LEARN button. Then press the LIGHT

button. The service LED will blink the status; ON is 2 blinks and OFF is 3

blinks.

LEARN Button

LIGHT Button

Service LED

(red)

LOCK Button

Press the push bar to

open or close the door.

Motion Sensor

Switch

TTC LEDs

(1, 5, 10 Minutes)

(Model 881LMW

only)

1 5 10

MODELS 881LMW AND 886LMW

MODEL 882LMW

LEARN Button

LIGHT Button

Service LED

(red)

LOCK Button

Command LED

(yellow)

Press the push bar to open or

close the door.

Command LED

(yellow)

ON Button

(Model 881LMW

only)

OFF Button

(Model 881LMW

only)

HOLD OPEN

(Model 881LMW

only)

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modiﬁ cations of this receiver

and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE

NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards for Home or ofﬁ ce use. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

ONE YEAR LIMITED WARRANTY

LiftMaster warrants to the first consumer purchaser of this product that it

is free from defect in materials and/or workmanship for a period of 1 year

from the date of purchase.

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	886LMW

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 886LMW stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

LiftMaster 64LM Manual

3 September 2024

LiftMaster CAPXSHOOD Manual

28 August 2024

LiftMaster myQ-SGC2WCH Manual

21 August 2024

LiftMaster CAPXS Manual

21 August 2024

LiftMaster MGJ5011U Manual

21 August 2024

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

OmniMount POWER40 Manual

17 Juni 2025

OmniMount OL50FT Manual

17 Juni 2025

Intermatic FD30MHW Manual

17 Juni 2025

Toorx SRX-EVOLVE Manual

17 Juni 2025

OmniMount WorldMount 2N1-L Manual

17 Juni 2025

OmniMount WorldMount 4N1-L Manual

17 Juni 2025

Intermatic FD60MC Manual

17 Juni 2025

Microchip MPFS160TLS Manual

17 Juni 2025

Hughes & Kettner Metal Master Manual

17 Juni 2025

Hansgrohe AXOR Montreux 16516310 Manual

17 Juni 2025