LiftMaster 975LM Manual

LiftMaster Ikke kategoriseret 975LM

Læs gratis den danske manual til LiftMaster 975LM (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om LiftMaster 975LM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

To avoid eye INJURY or damage to product:

• NEVER point the laser at anyone.

• NEVER look directly into the laser beam.

• NEVER disassemble the laser.

• The parking assist is NOT a substitute for safe parking

practices.

• Use of controls or adjustments, or the performance or

procedures other than specified can result in hazardous

radiation exposure.

• ONLY for use on LiftMaster manufactured garage door

openers.

LASER GARAGE PARKING ASSIST

MODEL 975LM AND 975LMC

INSTALLATION

1. Open your garage door and park your vehicle outside of the

garage.

2. Determine the mounting location on or near the ceiling and

fasten the parking assist using the screw and anchor provided

(Figure 1).

3. Depress tabs under the wires and temporarily remove the white

and white/black safety sensor wires from the garage door

opener.

4. Stripping the wires prior to installation:

If installing one parking assist: Separate white and white/

black wires and strip 7/16" (11 mm) of insulation from the

parking assist wires.

If installing two parking assists: Cut 6" (15 cm) of wires from

the end of one of the parking assist wires for use as connection

wires. Separate white and white/black wires and strip 7/16" (11

mm) of insulation from both ends of the connection wire.

5. Connecting the wires to install:

If installing one parking assist: Twist like colored wires for the

parking assist and the safety sensors together. Insert twisted

wires into quick-connect holes: white to white and white/black

to grey (Figure 2).*

If installing two parking assists: Separate white and white/

black wires and strip 7/16" (11 mm) of insulation from the end

of the parking assist wires. Twist like colored wires for the

parking assist, safety sensors and connection wire together.

Secure with wire nut (provided). Insert loose end of connection

wires into quick-connect holes: white to white and white/black

to grey (Figure 3).*

* Please reference your garage door opener owner’s manual for

proper wire installation.

SET UP AND ADJUSTMENT

1. Drive your vehicle into the garage and park in the location you

want to park your vehicle each time (Figure 4).

2. Activate the parking assist locator by obstructing the path of

the safety reversing sensors. The laser will emit a pulsing

bright red beam. Using the swivel mount, aim the red beam to

a location on the dash or hood that can easily be seen while

seated in the driver's seat.

NOTE: The laser will shut off automatically in 1 minute. If you are

not finished adjusting the beam and it turns off, simply obstruct

the path of the safety reversing sensors again to re-activate the

beam.

3. Sit in the driver's seat and confirm that you can easily see the

location of the red beam. This location is now your point of

reference for parking your vehicle (Figure 5). CAUTION: Do not

stare directly into the beam. Repeat steps for installation on

optional 2nd laser accessory kit.

White Safety

Sensor Wires

White Connection

Wire to Terminal

Repeat with white/black wires.

White Connection Wire Black/White

Connection Wire

Wire Nut

(provided)

White Parking

Assist Wires

Red White Grey

Quick-Connect Terminals

Parking Assist

Swivel Mount

White Safety

Sensor Wires

White Parking

Assist Wire

Red White Grey

Quick-Connect Terminals

Repeat with white/black wires.

White Connection Wires

Black/White

Connection Wires

Parking Assist (1)

Wire Nuts (2)

Labels (2) Not Shown

Screw 6ABx1-1/4" (1)

Anchor (1)

Carton Inventory

Figure 1

Figure 2

Figure 3

NOTE: Periodic adjustment of the beam may be required from

time to time and is to be used only with the vehicle used during

the initial setup. Re-set the adjustment according to SETUP and

ADJUSTING steps 1-3 for that vehicle.

OPERATION

1. Open the garage door by activating the automatic garage door

opener and drive your vehicle into parking space.

2. The red beam can be seen moving across the hood of your

vehicle as you drive further into the garage (Figure 5).

3. Stop the vehicle when the beam is positioned at the location

you confirmed in step 3 during the Set Up and Adjustment

(Figure 6).

NOTE: The laser is automatically actuated every time you drive

into your garage. The beam will automatically deactivate after

approximately 1 minute. A residual reflection of the red beam

from the windshield may appear on the walls or objects in your

garage. When operating a vehicle, always ensure that there are no

objects on the floor of the garage or in the path of your vehicle.

This parking assist is not a substitute for safe parking practices.

TROUBLESHOOTING

If the laser does not emit a beam:

• Verify nothing is obstructing the safety sensor lens.

• Verify nothing is blocking the parking assist lens.

• Verify that connections are not reversed wired.

• Verify that all connections are secure as identified in

theinstallation.

• Confirm that the parking assist is aimed toward thegarage

floor.

• Obstruct the path of the safety reversing sensors andlook for

the red spot on the garage floor.

Please refer to your Liftmaster owner's manual for additional

information on your garage door opener and the safety sensors.

REPLACEMENT PARTS LIST

Wire Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23B293

Parking Assist . . . . . . . . . . . . . . . . . . . . . . . . 975LM and 975LMC

To avoid eye INJURY or damage to product:

• NEVER point the laser at anyone.

• NEVER look directly into the laser beam.

• NEVER disassemble the laser.

• The parking assist is NOT a substitute for safe parking

practices.

• Use of controls or adjustments, or the performance or

procedures other than specified can result in hazardous

radiation exposure.

• ONLY for use on LiftMaster manufactured garage door

openers.

1-800-528-9131

LiftMaster.com

Parking

Assist

Wire

Parking Assist

Figure 4

Figure 5

Figure 6

CAUTION

ATTENTION

132C2469-1

LASER RADIATION

DO NOT STARE INTO BEAM

RAYONNEMENT LASER

NE PAS REGARDER DIRECTEMENT

LE RAYONNEMENT LASER

Maximum power output: < 1mW @ 635 - 670nm

Puissance de sortie maximum: < 1mW @ 635 - 670nm

CLASS II LASER PRODUCT

APPAREIL AU LASER DE CLASSE II

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	975LM

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 975LM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

LiftMaster 64LM Manual

3 September 2024

LiftMaster CAPXSHOOD Manual

28 August 2024

LiftMaster myQ-SGC2WCH Manual

21 August 2024

LiftMaster CAPXS Manual

21 August 2024

LiftMaster MGJ5011U Manual

21 August 2024

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Playtive IAN 304090 Manual

16 Juni 2025

Toorx SRX-85 Manual

16 Juni 2025

Cable Matters 180070 Manual

16 Juni 2025

Philips Avent SCD252 Manual

16 Juni 2025

Philips Q-Line 55BDL2050Q Manual

16 Juni 2025

EFX Delta DUDB4 Manual

16 Juni 2025

Foster Prep Station PS1000HR Manual

16 Juni 2025

OmniMount OBT60 Manual

16 Juni 2025

XO D34HPBF Manual

16 Juni 2025

Janitza 800-DI14 Manual

16 Juni 2025