LiftMaster 975LMC Manual

LiftMaster Ikke kategoriseret 975LMC

Læs gratis den danske manual til LiftMaster 975LMC (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om LiftMaster 975LMC, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
To avoid eye INJURY or damage to product:
• NEVER point the laser at anyone.
• NEVER look directly into the laser beam.
• NEVER disassemble the laser.
• The parking assist is NOT a substitute for safe parking
practices.
• Use of controls or adjustments, or the performance or
procedures other than specified can result in hazardous
radiation exposure.
• ONLY for use on LiftMaster manufactured garage door
openers.
LASER GARAGE PARKING ASSIST
MODEL 975LM AND 975LMC
INSTALLATION
1. Open your garage door and park your vehicle outside of the
garage.
2. Determine the mounting location on or near the ceiling and
fasten the parking assist using the screw and anchor provided
(Figure 1).
3. Depress tabs under the wires and temporarily remove the white
and white/black safety sensor wires from the garage door
opener.
4. Stripping the wires prior to installation:
If installing one parking assist: Separate white and white/
black wires and strip 7/16" (11 mm) of insulation from the
parking assist wires.
If installing two parking assists: Cut 6" (15 cm) of wires from
the end of one of the parking assist wires for use as connection
wires. Separate white and white/black wires and strip 7/16" (11
mm) of insulation from both ends of the connection wire.
5. Connecting the wires to install:
If installing one parking assist: Twist like colored wires for the
parking assist and the safety sensors together. Insert twisted
wires into quick-connect holes: white to white and white/black
to grey (Figure 2).*
If installing two parking assists: Separate white and white/
black wires and strip 7/16" (11 mm) of insulation from the end
of the parking assist wires. Twist like colored wires for the
parking assist, safety sensors and connection wire together.
Secure with wire nut (provided). Insert loose end of connection
wires into quick-connect holes: white to white and white/black
to grey (Figure 3).*
* Please reference your garage door opener owner’s manual for
proper wire installation.
SET UP AND ADJUSTMENT
1. Drive your vehicle into the garage and park in the location you
want to park your vehicle each time (Figure 4).
2. Activate the parking assist locator by obstructing the path of
the safety reversing sensors. The laser will emit a pulsing
bright red beam. Using the swivel mount, aim the red beam to
a location on the dash or hood that can easily be seen while
seated in the driver's seat.
NOTE: The laser will shut off automatically in 1 minute. If you are
not finished adjusting the beam and it turns off, simply obstruct
the path of the safety reversing sensors again to re-activate the
beam.
3. Sit in the driver's seat and confirm that you can easily see the
location of the red beam. This location is now your point of
reference for parking your vehicle (Figure 5). CAUTION: Do not
stare directly into the beam. Repeat steps for installation on
optional 2nd laser accessory kit.
White Safety
Sensor Wires
White Connection
Wire to Terminal
Repeat with white/black wires.
White Connection Wire Black/White
Connection Wire
Wire Nut
(provided)
White Parking
Assist Wires
Red White Grey
Quick-Connect Terminals
Parking Assist
Swivel Mount
White Safety
Sensor Wires
White Parking
Assist Wire
Red White Grey
Quick-Connect Terminals
Repeat with white/black wires.
White Connection Wires
Black/White
Connection Wires
Parking Assist (1)
Wire Nuts (2)
Labels (2) Not Shown
Screw 6ABx1-1/4" (1)
Anchor (1)
Carton Inventory
Figure 1
Figure 2
Figure 3
NOTE: Periodic adjustment of the beam may be required from
time to time and is to be used only with the vehicle used during
the initial setup. Re-set the adjustment according to SETUP and
ADJUSTING steps 1-3 for that vehicle.
OPERATION
1. Open the garage door by activating the automatic garage door
opener and drive your vehicle into parking space.
2. The red beam can be seen moving across the hood of your
vehicle as you drive further into the garage (Figure 5).
3. Stop the vehicle when the beam is positioned at the location
you confirmed in step 3 during the Set Up and Adjustment
(Figure 6).
NOTE: The laser is automatically actuated every time you drive
into your garage. The beam will automatically deactivate after
approximately 1 minute. A residual reflection of the red beam
from the windshield may appear on the walls or objects in your
garage. When operating a vehicle, always ensure that there are no
objects on the floor of the garage or in the path of your vehicle.
This parking assist is not a substitute for safe parking practices.
TROUBLESHOOTING
If the laser does not emit a beam:
• Verify nothing is obstructing the safety sensor lens.
• Verify nothing is blocking the parking assist lens.
• Verify that connections are not reversed wired.
• Verify that all connections are secure as identified in
theinstallation.
• Confirm that the parking assist is aimed toward thegarage
floor.
• Obstruct the path of the safety reversing sensors andlook for
the red spot on the garage floor.
Please refer to your Liftmaster owner's manual for additional
information on your garage door opener and the safety sensors.
REPLACEMENT PARTS LIST
Wire Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23B293
Parking Assist . . . . . . . . . . . . . . . . . . . . . . . . 975LM and 975LMC
To avoid eye INJURY or damage to product:
• NEVER point the laser at anyone.
• NEVER look directly into the laser beam.
• NEVER disassemble the laser.
• The parking assist is NOT a substitute for safe parking
practices.
• Use of controls or adjustments, or the performance or
procedures other than specified can result in hazardous
radiation exposure.
• ONLY for use on LiftMaster manufactured garage door
openers.
1-800-528-9131
LiftMaster.com
Parking
Assist
Wire
Parking Assist
Figure 4
Figure 5
Figure 6
CAUTION
ATTENTION
132C2469-1
LASER RADIATION
DO NOT STARE INTO BEAM
RAYONNEMENT LASER
NE PAS REGARDER DIRECTEMENT
LE RAYONNEMENT LASER
Maximum power output: < 1mW @ 635 - 670nm
Puissance de sortie maximum: < 1mW @ 635 - 670nm
CLASS II LASER PRODUCT
APPAREIL AU LASER DE CLASSE II

Produkt Specifikationer

Mærke: LiftMaster
Kategori: Ikke kategoriseret
Model: 975LMC

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 975LMC stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret LiftMaster Manualer

LiftMaster

LiftMaster 041-0405-000 Manual

15 Juni 2025
LiftMaster

LiftMaster LMHNTG Manual

4 September 2024
LiftMaster

LiftMaster CAPXSTKPL Manual

3 September 2024
LiftMaster

LiftMaster BG790 Manual

3 September 2024
LiftMaster

LiftMaster 64LM Manual

3 September 2024
LiftMaster

LiftMaster CAPXSHOOD Manual

28 August 2024
LiftMaster

LiftMaster myQ-SGC2WCH Manual

21 August 2024
LiftMaster

LiftMaster CAPXS Manual

21 August 2024
LiftMaster

LiftMaster MGJ5011U Manual

21 August 2024
LiftMaster

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vulcan

Vulcan 1048C Manual

16 Juni 2025
Playtive

Playtive IAN 91495 Manual

16 Juni 2025
Playtive

Playtive IAN 270612 Manual

16 Juni 2025
Playtive

Playtive IAN 315026 Manual

16 Juni 2025
Playtive

Playtive IAN 115585 Manual

16 Juni 2025
Playtive

Playtive 10464 Manual

16 Juni 2025
Playtive

Playtive HG03821 Manual

16 Juni 2025
Martin

Martin VC-Strip Manual

16 Juni 2025
Playtive

Playtive HG06316 Manual

16 Juni 2025
Playtive

Playtive HG05102 Manual

16 Juni 2025