LiftMaster LMRRUL Manual

LiftMaster Ikke kategoriseret LMRRUL

Læs gratis den danske manual til LiftMaster LMRRUL (16 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 8 anmeldelser. Har du et spørgsmål om LiftMaster LMRRUL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

Introduction

The LiftMaster® Retro-Reﬂ ective Photoelectric

Sensor provides non-contact monitored entrapment

protection. For use with LiftMaster® UL Listed

gate operators. The sensor is a UL Recognized

Component and meets UL 325 requirements.

Monitored external entrapment protection devices

MUST be installed at each Entrapment Zone. Refer to

gate operator manual for compatibility with LMRRUL

sensor.

Speciﬁ cations

Max Range: 50 ft. (15.2 m)

Sensor Dimensions with Hood:

2.29" W x 3.72" H x 2.76" D

Reﬂ ector Dimensions with Hood:

2.61" W x 4.72" H x 2" D

Cable Length: 10 ft. (3 m)

Operating Temperature: -40˚C to 65˚C

(-40˚F a 149˚F)

Outdoor Rating: Nema 4X

Input voltage:

Sensor: Black/red wires 6.8 VDC, 20mA

Heater: Green/white wires 10-40VDC or 8-28 VAC, 2

watts max., 170mA @ 12 VDC/VAC,

85mA@ 24 VDC/VAC

Heater: Thermostatically controlled, NOT

recommended for solar applications

MONITORED RETRO-REFLECTIVE

PHOTOELECTRIC SENSOR

Model LMRRUL

To prevent possible SERIOUS INJURY or DEATH from a closing gate or door:

• Read and follow ALL instructions.

• Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the photoelectric sensor.

• The gate or door MUST be in the fully opened or closed position BEFORE installing the LiftMaster®

Monitored Entrapment Protection device.

• Correctly connect and align the photoelectric sensor.

• Install the photoelectric sensor so that the center of the sensor window is NO HIGHER than

4-1/2" (11.4cm) above the ﬂ oor for door operators and 26" (66 cm) above grade for gate operators.

• Monitored external entrapment protection devices MUST be installed per the operator installation

manual at each Entrapment Zone.

• The sensor and reﬂ ector MUST be mounted vertically.

• Use the provided reﬂ ector ONLY.

• Test the gate operator and ALL photoelectric sensors monthly. Replace ANY damaged devices.

• SAVE THESE INSTRUCTIONS.

WARNING: This product can expose you to chemicals including lead, which are known

to the State of California to cause cancer or birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov.

Installation

IMPORTANT: The sensor and the reﬂ ector MUST be mounted vertically. Disconnect ALL power to the

operator.

1. Attach the mounting bracket to the post with 1/4"-20 screws. Drill a hole in the post through the center

hole in the bracket. Optional: If installing to a square post or ﬂ at surface, you may attach the sensor

bracket directly to the post without using the mounting bracket. Make sure the location of the sensor

follows the speciﬁ ed measurements. If installing multiple sensors in close proximity, mount the sensors on

opposite sides to avoid crosstalk.

2. Slide the bottom sensor bracket onto the studs of the mounting bracket and secure with 1/4"-20 lock nuts.

Make sure the bracket legs are facing down.

3. Loosely attach the top sensor bracket with 10-32x1" thread-locking screws. Make sure the slots are

facing up.

4. Place the sensor in the bracket and tighten the screws just enough to allow the sensor to rotate inside the

bracket.

5. Slide the hood over the sensor until it snaps into place. Secure hood with the M3 screw. The hood MUST

be installed on the sensor.

6. Route wires through the center hole of the mounting bracket and into the post. Optional: Use conduit with

NEMA 4X compatible 1/2"-14 NPT ﬁ tting (not provided).

7. Place the reﬂ ector in the reﬂ ector hood.

8. Secure the reﬂ ector and hood to the bracket with 8-32x1" screws. Secure the bottom of the reﬂ ector to the

hood with 8-32x1" screws.

9. Mount the reﬂ ector a minimum of 3 ft. (.9 m) and maximum of 50 ft. (15.2 m) away from the sensor.

Carton Inventory

• Photoelectric sensor with hood

and bracket

• Reﬂ ector with hood and

bracket

• Wire cover

• Screws 8-32x1" (4)

• Lock nuts 8-32 (4)

• Screws 8-32x3/8" (2)

• Thread-locking screws

10-32x1" (2)

• Screws 1/4"-20x1-1/4" (6)

• Lock nuts 1/4"-20 (2)

• M3 screw (1)

• Set screw 10-32x3/8" (1)

Tools Needed

• Philips screwdriver

• 1/8" Allen wrench

• 7/16" socket

• 11/32" socket

• 5/32" Allen key

• 3/32" Allen key

≤ 5" (12.7 cm)

from gate or wall Optional for

square post

Door operators:

4-1/2" (11.4 cm)

Gate operators:

4" (10.2 cm)-26" (66 cm)

Door operators: 4-1/2" (11.4 cm)

Gate operators: 4" (10.2 cm)-26" (66 cm)

≤ 5" (12.7 cm)

from gate or wall

Illustrations are for reference only; your application may look different.

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	LMRRUL

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster LMRRUL stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster SL580 Manual

8 August 2025

LiftMaster HCT12 Manual

7 August 2025

LiftMaster MyQ 827LM Manual

7 August 2025

LiftMaster SL595 Manual

7 August 2025

LiftMaster CAPXSTK Manual

7 August 2025

LiftMaster 66LM Manual

7 August 2025

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JILONG JL097205NPF Manual

14 September 2025

Brandson 306570 Manual

14 September 2025

Nedis PIM30012EGY Manual

14 September 2025

Neutrik SCD-W Manual

14 September 2025

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025