LiftMaster LMTBUL Manual

LiftMaster Ikke kategoriseret LMTBUL

Læs gratis den danske manual til LiftMaster LMTBUL (16 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 7 anmeldelser. Har du et spørgsmål om LiftMaster LMTBUL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

Introduction

The LiftMaster® Photoelectric Sensors provide

non-contact monitored entrapment protection. For

use with LiftMaster® UL Listed gate operators. The

sensors are UL recognized components and meet UL

325 requirements. Monitored external entrapment

protection devices MUST be installed at each

Entrapment Zone. Refer to gate operator manual for

compatibility with LMTBUL sensor.

Speciﬁ cations

Max Range: 90 ft. (27.4 m)

Sensor Dimensions with Hood: 2.29" W x 3.72" H x

2.76" D

Cable Length: 10 ft. (3 m)

Operating Temperature: -40˚C to 65˚C (-40˚F to

149˚F)

Outdoor Rating: Nema 4X

Heater: Thermostatically controlled, NOT

recommended for solar applications

Input Voltage:

Sensor: Black/red wires 6.8 VDC, 20mA

Heater: Green/white wires 10-40VDC or 8-28 VAC,

4watts max., 170mA per pair @ 24 VDC/VAC,

340mA per pair @ 12 VDC/VAC

MONITORED THROUGH BEAM

PHOTOELECTRIC SENSOR

Model LMTBUL

To prevent possible SERIOUS INJURY or DEATH from a closing gate or door:

• Read and follow ALL instructions.

• Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the photoelectric sensors.

• The gate or door MUST be in the fully opened or closed position BEFORE installing the LiftMaster®

Monitored Entrapment Protection device.

• Correctly connect and align the photoelectric sensor.

• Install the photoelectric sensor so that the center of the sensor window is NO HIGHER than 4-1/2"

(11.4cm) above the ﬂ oor for door operators and 26" (66 cm) above grade for gate operators.

• Monitored external entrapment protection devices MUST be installed per the operator installation

manual at each Entrapment Zone.

• The sensors MUST be mounted vertically.

• Test the gate operator and ALL photoelectric sensors monthly. Replace ANY damaged devices.

• SAVE THESE INSTRUCTIONS.

WARNING: This product can expose you to chemicals including lead, which are known

to the State of California to cause cancer or birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov.

Installation

IMPORTANT: Disconnect ALL power to the operator.

1. Determine the mounting locations for the sensors following the measurements below. If installing

multiple sensors in close proximity, mount the emitters on opposite sides to avoid crosstalk. The receiver

and emitter can be identiﬁ ed by the labels on the back.

2. Attach the mounting bracket to the post with 1/4"-20 screws. Drill a hole in the post through the center

hole in the bracket. Optional: If installing to a square post or ﬂ at surface, you may attach the sensor

bracket directly to the post without using the mounting bracket.

3. Slide the bottom sensor bracket onto the studs of the mounting bracket and secure with 1/4"-20 lock

nuts. Make sure the bracket legs are facing down.

4. Loosely attach the top sensor bracket with 10-32x1" thread-locking screws. Make sure the slots are facing

up.

5. Place the sensor in the bracket and tighten the screws just enough to allow the sensor to rotate inside the

bracket.

6. Slide the hood over the sensor until it snaps into place. Secure hood with the M3 screw.

7. Route wires through the center hole of the mounting bracket and into the post. Optional: Use conduit

with NEMA 4X compatible 1/2"-14 NPT ﬁ tting (not provided).

Carton Inventory

• Emitter with hood and bracket

• Receiver with hood and

bracket

• Wire covers (2)

• Screws 8-32x3/8" (4)

• Screws 1/4"-20x1-1/4" (8)

• Lock nuts 1/4"-20 (4)

• Thread-locking screws

10-32x1" (4)

• M3 screw (2)

• Set screw 10-32x3/8" (2)

• 5/32 Allen key

• 3/32 Allen key

Tools Needed

• Philips screwdriver

• 7/16" socket

Distance from ground:

For gate operators:

4" (10.2 cm)-26" (66 cm)

For door operators:

4-1/2" (11.4 cm)

Mounting

bracket

Bottom sensor

bracket

Top sensor

bracket

Distance from gate or wall:

≤ 5" (12.7 cm)

Illustrations are for reference only;

your application may look different.

Distance between sensors:

3 ft. (.9 m)-90 ft. (27.4 m)

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	LMTBUL

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster LMTBUL stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

LiftMaster 64LM Manual

3 September 2024

LiftMaster CAPXSHOOD Manual

28 August 2024

LiftMaster myQ-SGC2WCH Manual

21 August 2024

LiftMaster CAPXS Manual

21 August 2024

LiftMaster MGJ5011U Manual

21 August 2024

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Festo DFM-32-100-B-PPV-A-KF Manual

17 Juni 2025

Playtive IAN 285777 Manual

17 Juni 2025

Festo VAEM-L1-S-M3-26 Manual

17 Juni 2025

Festo DFPC-320 Manual

17 Juni 2025

EFX ICAK12 Manual

17 Juni 2025

Bearware 307294 Manual

17 Juni 2025

Futaba MC-9200H/A Manual

17 Juni 2025

Hansgrohe AXOR Montreux 16517800 Manual

17 Juni 2025

OmniMount 2N1-S Manual

17 Juni 2025

Festo DSNU-S-12- -F1A Manual

17 Juni 2025