LiftMaster LMWETXU Manual

LiftMaster Ikke kategoriseret LMWETXU

Læs gratis den danske manual til LiftMaster LMWETXU (24 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 7 anmeldelser. Har du et spørgsmål om LiftMaster LMWETXU, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/24
MONITORED
WIRELESSEDGEKIT
Models LMWEKITU and LMWETXU
To prevent possible SERIOUS INJURY or DEATH from a closing gate or door:
• Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the wireless
edgekit.
• The gate or door MUST be in the fully opened or closed position BEFORE installing the
LiftMaster® Monitored Entrapment Protection device.
• Correctly install and connect the wireless edge kit.
• LiftMaster® Monitored Entrapment Protection devices are for use with LiftMaster
® UL 325
compliant Gate and Commercial Door Operators ONLY. Use with ANY other product voids
the warranty.
• Monitored external entrapment protection devices MUST be installed per the operator
installation manual for each Entrapment Zone.
WARNING: This product can expose you to chemicals including lead, which are
known to the State of California to cause cancer or birth defects or other reproductive
harm. For more information go to www.P65Warnings.ca.gov.
INTRODUCTION
The LiftMaster Wireless Edge Kit provides a Bluetooth
® connection between a LiftMaster monitored
resistive edge (not included) and the gate operator. Maximum range is 130 ft. (39.6 m.) (for best
results install with a clear line of sight between transmitter and receiver, objects in the path may
reduce range). You can program up to 4 transmitters to the receiver. The kit works with LiftMaster
monitored resistive edge sensors ONLY. Contact closure edge sensors are NOT supported.
Refer to your gate operator manual to ensure compatibility (LMWEKITU and LMWETXU is listed
under Monitored Entrapment Protection devices of the section). Transmitter and Accessories
receiver are UL Recognized Components and meet UL 325 requirements. A monitored entrapment
protection device MUST be installed in each entrapment zone.
Compatible LiftMaster® Gate Operators:
• CSW24U/UL • HDSL24UL • LA412U/UL • HDSW24UL
• RSW12U/UL • CSL24U/UL • LA500U/UL • IHSL24UL
• SL585U/UL • RSL12U/UL • CSW200U/UL • INSL24UL
• LA400U/UL • SL5959U/UL • SL300U/UL
Illustrations in manual are for reference only, your application may look different.
CARTON INVENTORY
Transmitter Model LMWETXU Receiver
10-16 x 3/4" Screw (4)
I2C Interface Board
4-40 x 1/4" Screw (2)
6-32 x 1" Screw (for metal)
6-19 x 1" Screw (for plastic)
Spacer
Mounting Bracket (2)
Wire Clip
Cable ties (3)
8-32 x 3/8" Screw (2)
or
AA Lithium Batteries (2)
Energizer
® Ultimate Lithium AA L91
REQUIRED as replacements
Double hole Heyco connectorSingle hole Heyco connector
WIRE THE RECEIVER
IMPORTANT: Disconnect ALL power to the operator.
1. Find your operator diagram on pages 5-7 to see the mounting location for
the receiver and wire routing.
2. Open the receiver housing.
3. Route the wire harness from the receiver to the operator. Connect the wire harness
to one of the following locations depending on your operator and application:
• The EXP. BOARD or EXPANSION terminal on the control board.
• The WIRELESS EDGE terminal on the expansion board (if installed).
• One of the data bus terminals on the relay adapter board: Models HDSL24UL,
and HDSW24UL ONLY.
• The I2C interface board: Required ONLY when using an expansion board with
a single terminal labeled TO MAIN BOARD. Install and connect as
shownbelow (if installed).
4. Tighten the Heyco connector with 25 in. lbs. of torque to make receiver watertight.
5. Reconnect power to the operator. The receiver blue power LED will come on.
Expansion Board
TO MAIN BOARD terminal
Expansion Board
(if applicable)
Relay Adapter Board
(if applicable)
6-19 x 1"
(for plastic)
6-32 x 1"
(for metal)
Control Board
Tighten Heyco nut
to 25 in. lbs. torque
Receiver
OR
OR OR
To Control Board
To Receiver
I2C Interface Board
(if applicable)
OR
1

Produkt Specifikationer

Mærke: LiftMaster
Kategori: Ikke kategoriseret
Model: LMWETXU

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster LMWETXU stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret LiftMaster Manualer

LiftMaster

LiftMaster SL580 Manual

8 August 2025
LiftMaster

LiftMaster HCT12 Manual

7 August 2025
LiftMaster

LiftMaster MyQ 827LM Manual

7 August 2025
LiftMaster

LiftMaster SL595 Manual

7 August 2025
LiftMaster

LiftMaster CAPXSTK Manual

7 August 2025
LiftMaster

LiftMaster 66LM Manual

7 August 2025
LiftMaster

LiftMaster 041-0405-000 Manual

15 Juni 2025
LiftMaster

LiftMaster LMHNTG Manual

4 September 2024
LiftMaster

LiftMaster CAPXSTKPL Manual

3 September 2024
LiftMaster

LiftMaster BG790 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

RADEMACHER

RADEMACHER Troll Comfort-3D 5635 Manual

1 November 2025
Beverage-Air

Beverage-Air VueMax VMHC-7-1-B Manual

1 November 2025
SmallRig

SmallRig 4842 Manual

1 November 2025
Ikea

Ikea TALGJE 702.982.38 Manual

1 November 2025
Lindy

Lindy 43339 Manual

1 November 2025
Ikea

Ikea VINTERFINT 805.800.24 Manual

1 November 2025
RADEMACHER

RADEMACHER RolloTron Schwenkwickler Comfort 1500 Manual

1 November 2025
Lantronix

Lantronix ION C2110 Manual

1 November 2025
Wiesenfield

Wiesenfield WIE-CHP-110 Manual

1 November 2025
Ikea

Ikea KLOTTHUJA 105.506.76 Manual

1 November 2025