LYYT ILADC4 Manual

LYYT Modtager ILADC4

Læs gratis den danske manual til LYYT ILADC4 (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 10 anmeldelser. Har du et spørgsmål om LYYT ILADC4, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
ILC4 and ILA4
IN-LINE CONTROLLER AND
AMPLIFIER FOR RGB LED TAPE
Item ref: 2 153.771UK, 153.70 UK,
153.701UK
User Manual
WARNING: These products are intended for professional installation of RGB LED tape and
should be connected by qualified personnel in accordance with electrical safety standards.
Ensure that the rated load indicated is not exceeded.
Installation
The ILC4 controller can be employed to control Fluxia RGB LED tape operating from a 5-24Vdc
power supply Maximum short term current load is rated at 3 x 4A. For constant full power .
output, it is advised to limit this to 3 x 2A load.
There are 2 versions of Fluxia RGB LED tape - 153.720UK has 60 LEDs per metre and
153.7 has 30 LEDs per metre. It is recommended that each controller is connected to no 21UK
more than 300 RGB LEDs (i.e 1 x 5m roll of 153.720UK or 2 x rolls of 153.721UK connected in
parallel).
For longer runs, each subsequent roll should be linked on using the ILA4 amplifier.
The ILA4 also accepts 5-24Vdc and connects from the end of a controlled length of RGB LED
tape to the beginning of the next length of RGB LED tape to match the patterns/colours of the
first tape. (also 3 x 4A peak, 3 x 2A continuous output)
Connection is via a 4-pin coupler, as supplied with Fluxia RGB LED tape.
E on the LED tape. nsure that the red triangle is connected to “+” or “Common”
153.702 , 153.701UK User Manual UK
Controls
• To switch LEDs on or off, press and hold
Speed/Dim/On button for 2 seconds
• Mode/Demo button steps through the 8 preset
programmes in sequence (shown below)
• Pressing Speed/Dim/Colour cycles through 10 different
speed levels
• Holding the Mode/Demo button for 2 seconds enters a
demo mode, cycling through all presets
• Press the Colour button to enter static colour mode
• Pressing Colour again changes to one of 20 colours
• Pressing Speed/Dim/On in static colour mode dims the
LEDs through 5 levels of brightness
Preset
Name
Description
1 - 2
Scrolls
2 types of scrolls through full spectrum of colours
3
RGB Glow
Fade between fully on and half through Red, Green, Blue
4
7 Colour Glow
Fade between fully on and half through 7 different colours
5 - 10
Static Glows
Glow presets for Blue, Cyan, Green, Red, White
11
RGB Jump
Switch between Red, Green and Blue
12
6 Colour Jump
Switch between 6 different colours
13
RGB Flash
Flash on and off through Red, Green and Blue
14 18-
Static Strobes
Regular, very short burst for Blue, Cyan, Green, Red, White
19
RGB Strobe
Regular, very short burst through Red, Green, Blue
Specifications
Power supply
5-24Vdc, 12A (to supply 3 x 4A max 50% duty cycle) –
Lead length (power input)
100mm
Connections
4-pin socket (Common+ / Green / Red / Blue)
Controller dimensions
42 x 13 x 5mm
Weight
4.8g
Errors and omissions excepted.
Copyright© 2018. AVSL Group Ltd.

Produkt Specifikationer

Mærke: LYYT
Kategori: Modtager
Model: ILADC4

Har du brug for hjælp?

Hvis du har brug for hjælp til LYYT ILADC4 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager LYYT Manualer

LYYT

LYYT ILADC4 Manual

12 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Musical Fidelity

Musical Fidelity B1xi Manual

12 August 2025
Artsound

Artsound MX60MKII Manual

12 August 2025
NAD

NAD CI 8-120 DSP V2 Manual

12 August 2025
NAD

NAD CI 8-150 DSP V2 Manual

12 August 2025
ESX

ESX Signum SX1000.1 Manual

12 August 2025
ESX

ESX Signum SX800.4 Manual

12 August 2025
ESX

ESX Signum SX800.2 Manual

12 August 2025
Mooer

Mooer F15i Li Manual

12 August 2025
Yamaha

Yamaha MusicCast RX-S602 Manual

10 August 2025
Strong

Strong SRT 3032 Manual

10 August 2025