Martin MAC Viper Quadray Manual

Martin Lettelse MAC Viper Quadray

Læs gratis den danske manual til Martin MAC Viper Quadray (8 sider) i kategorien Lettelse. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Martin MAC Viper Quadray, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Martin MAC Viper Quadray™ Quadray Installation and DMX Control Guide 1

MAC Viper Quadray™ Module

Installation and Control Guide

Introduction

This Guide explains how to install the Martin MAC Viper Quadray™ Module, P/N 91614052, on a Martin MAC

Viper AirFX™ fixture and control the Quadray functions via DMX.

Installation takes only a few minutes. If you keep the standard components you remove when you install the

Quadray module, the Quadray components can be uninstalled and the fixture returned to standard configuration

at any time.

Warning! Follow all the safety precautions in the MAC Viper AirFX user manual and use the

manual for reference when installing the Quadray Module and using the modified product. The

user manual is supplied with fixtures, but check that you have the latest revision of the user

manual. This is available for download from the Product Support page for the MAC Viper AirFX

at www.martin.com

Warning! Disconnect the fixture from power and allow to cool for at least 2 hours and 45

minutes before starting work.

Warning! The Quadray Module must be installed by qualified professional technicians only.

Read all of this Installation Guide carefully before starting to install the module.

Important! Make sure that the front of the head does not face the sun or any other strong light

source directly for longer than a few seconds at any time. Lenses can focus the sun's rays

inside the fixture, causing internal damage and creating a possible fire risk

Important! Do not use concentrated alcohol solutions, abrasive products or solvents to clean

the components in the Quadray Module. If wiping with a soft, lint-free cloth dampened with

distilled water is not effective, damp the cloth with distilled water containing 20% isopropyl

alcohol in solution.

If you have any questions about how to install the Quadray Module or use it safely, please contact your local

Martin distributor (see www.martin.com/distributors for details) or call the Martin 24-hour service hotline on +45

8740 0000, or in the USA on 1-888-tech-180.

Software compatibility

MAC Viper AirFX firmware version 1.2.0 or later is required for operation with the Quadray Module. The latest

version of the MAC Viper AirFX firmware is available for download from the MAC Viper AirFX Product Support

page on the Martin™ website at www.martin.com

Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic

loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this installation note. The

Martin logo, the Martin name and all other trademarks in this document pertaining to services or products by Martin Professional A/S or

its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.

P/N 35000629 Rev. C

2 Martin MAC Viper Quadray™ Module Installation and DMX Control Guide

Preparation

The Quadray Module accessory contains the following items:

• MAC Viper Quadray Module with integral wireset

• This Installation Guide

Keep the protective packaging supplied with the module for possible re-use.

Without damaging the wiring, remove the adhesive tape that is applied to avoid damage or loss during transport:

tape holds the safety wire and wireset together and retains the two screws in the module connector on the end of

the wireset.

Calibration values for each individual module are printed on a label on the module connector. Four values are

given for the four lenses . Each time you install a Quadray Module on a fixture, you must enter its L1 to L4

calibration values in the CALIBRATION menu in the fixture’s control panel. Note these values and store them for

future use when installing the module on other fixtures.

Installation procedure

Warning! Disconnect from power and allow to cool for 30 minutes before opening the head.

To install the Quadray Module on a standard Martin MAC Viper AirFX fixture:

1. Disconnect the fixture from power and allow components to cool for 30 minutes.

2. Place the fixture on a secure work surface. Tilt the head vertically upwards and apply the tilt lock.

3. See Figure 1. Remove the top head cover by loosening its Torx 25 captive retaining screws A until the screws

turn freely (the top head cover is on top of the head with the text on the back of the head facing the right way

up). Lift the front of the cover slightly away from the head, then slide the cover towards the front of the head to

release the rear of the cover. You can allow the head cover to hang on its safety wire, but for easiest access

press the cover’s safety wire retaining clip B in towards the head chassis, slide the clip down until you can

remove it, then remove the head cover completely from the fixture.

4. See Figure 2. Release the four screws from the front lens assembly, then

release the front lens safety attachment. Remove the front lens assembly

and store it for possible re-use if the fixture is returned to standard

configuration at a later time.

Figure 1: Removing the head covers

A A

Figure 2

Produkt Specifikationer

Mærke:	Martin
Kategori:	Lettelse
Model:	MAC Viper Quadray

Har du brug for hjælp?

Hvis du har brug for hjælp til Martin MAC Viper Quadray stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lettelse Martin Manualer

Martin ERA 700 Performance IP Manual

29 August 2024

Martin Thrill Vertical Fogger Manual

23 August 2024

Martin Extube Manual

22 August 2024

Martin MUM Manual

22 August 2024

Martin Freekie Manual

22 August 2024

Martin P3-100 Manual

21 August 2024

Martin THRILL Multi-FX LED Manual

21 August 2024

Martin Fixture Beam Analyzer Manual

21 August 2024

Martin MAC Ultra Wash Manual

21 August 2024

Martin RUSH MH 4 Beam Manual

21 August 2024

Lettelse Manualer

Nyeste Lettelse Manualer

Dainolite V166-1W Manual

5 April 2025

Dainolite OFE-161P Manual

5 April 2025

Dainolite DMLED10-A-5D Manual

5 April 2025

Dainolite DM1958F Manual

5 April 2025

NUVO Ballerina 60/1265 Manual

4 April 2025

NUVO SF77/196 Manual

4 April 2025

NUVO Ballerina 60/329 Manual

4 April 2025

NUVO Cordello 60/7883 Manual

4 April 2025

NUVO Destin 60/7706 Manual

4 April 2025

NUVO Livingston 60/7669 Manual

4 April 2025