Mikrotik CRS304-4XG-IN Manual

Mikrotik Ikke kategoriseret CRS304-4XG-IN

Læs gratis den danske manual til Mikrotik CRS304-4XG-IN (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Mikrotik CRS304-4XG-IN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

CRS304-4XG-IN

CRS304-4XG-INCRS304-4XG-IN

CRS304-4XG-IN

This is a compact and powerful device designed to simplify your 10 Gigabit network setups. It comes equipped with 4x10G Ethernet ports that are ready to

use right out of the box.

Safety Warnings

Before you work on any MikroTik equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for

preventing accidents. The installer should be familiar with network structures, terms, and concepts.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for making sure, that

the Installation of the equipment is compliant with local and national electrical codes.

Do not attempt to disassemble, repair, or modify the device. If service is needed, please contact MikroTik support.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity, or hot environments.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

The socket-outlet shall be installed near the equipment and shall be easily accessible.

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power adapter from the power outlet.

To avoid contamination of the environment, separate the device from household waste and dispose of it in a safe manner, for example, in designated

areas. Become familiar with procedures for properly transporting the equipment to designated collection points in your area

Quick start

Connect with your computer to the device;

Connect the device to a power source (see );Powering

Configuration should be made using a web browser WebFig or the WinBox configuration tool ;https://mt.lv/WinBox

Open in a web browser to start setup. If the IP address is unavailable, use WinBox and connect using the MAC address. The  http://192.168.88.1

username is "admin," and there is no password (or, for some models, check user and wireless passwords on the sticker);

Click the "Check for updates" button and update RouterOS to the latest version;

For a manual update, visit the products page at to find your product. The required packages are accessible under  https://mikrotik.com/products

the "Support&Downloads" menu;

Upload downloaded packages to the WinBox "Files" menu and reboot the device;

By upgrading your RouterOS software to the latest version, you can ensure optimal performance, stability, and security updates;

Set up your router password.

CRS3xx and CSS326-24G-2S+ series Manual

Mounting

This indoor switch offers multiple mounting options, including a side DIN rail mount and standard screw points on the back for easy integration. The DIN

rail mount can also be repositioned to the back.

Powering

The device can be powered through two DC power jacks (for redundancy failover), a 2-pin terminal, or the MGMT/BOOT Ethernet PoE-in port:

Direct input power jacks DC1, DC2 (5.5 mm outside and 2 mm inside, female, pin positive) accept DC 12-57 V DC.

MGMT/BOOT Ethernet PoE-in port accepts passive or 802.3af/at Power over Ethernet in the range of DC 36-57 V.

2-pin terminal accepts DC 12-57 V DC.

The power consumption of this device is 21 W at maximum load and 15 W at minimum.

When powering this device with 802.3af/at, we recommend avoiding grounding for optimal compatibility.

Connecting to a POE Adapter:

Connect the device to the included PoE injector using an Ethernet cable, attaching it to the data+power or PoE-out port;

Connect the data end of the PoE injector to the computer;

Connect the power adapter to the PoE injector.