Mikrotik LHG XL HP5 Manual

Mikrotik Adgangspunkt LHG XL HP5

Læs gratis den danske manual til Mikrotik LHG XL HP5 (3 sider) i kategorien Adgangspunkt. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Mikrotik LHG XL HP5, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
LHG series
Quick Setup Guide and Warranty Information
The LHG is an outdoor wireless router with a built in directional antenna. It can be used as a CPE or for point to point links (use RouterOS
wireless mode “bridge” to work as a single-client AP for point to point scenarios).
Assembly
Attach the two legs to the LHG case, then snap the assembed LHG unit to the grid in the appropriate locations. Fix the legs in place with two
self thread screws (Included, use philips screw driver PH2). The package also contains a grounding cable connector, and a 5 degree angle
adapter. More detailed instructions available on the product page on http://routerboard.com
Connecting
1. Open the ethernet door to connect an ethernet cable to the ethernet port, connect the other end of the ethernet cable to the included
PoE injector
2. Plug the PoE injector into your network switch or ISP internet outlet
3. Plug the included power supply into the PoE injector to start up the device
4. Set LAN computer IP configuration to (DHCP)automatic
5. Default IP address of the unit is 192.168.88.1, open this address in your web browser to start configuration. The username is admin
and there is no password
The device is preconfigured as a wireless client, and all you need to do is select the AP to connect to and set a device password. You can do
this in the quickSET tab that is loaded by default.
In case IP connection is not available, Winbox can be used to connect to the MAC address of the device.
In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the device when starting it,
until the LED light turns off, then the device will start to look for Netinstall servers.
More information about using RouterOS and connecting to this device in our documentation: http://mt.lv/help
Powering
The device accepts powering only from Passive PoE injectors
Extension Slots and Ports
One 10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or cross-
over cables for connecting to other network devices.
One Integrated 2x2 MIMO wireless device with built in grid antenna
Buttons and Jumpers
RouterBOOT reset button (RESET, front panel) has three functions:
•Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds)
•Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10 seconds)
•Or Keep holding the button for 5 more seconds until until LED turns off, then release it to make the RouterBOARD look for Netinstall
servers (total 15 seconds)
Power on device with pressed reset button and release it right away in order to boot backup RouterBOOT (useful for debugging situations where
RouterOS and Netinstall do not work).
The device includes a grounding connection (marked ) which you should connect to the grounding installation of the tower or building where ⏚
the device will be used. This is to substantially reduce risk of ESD and lightning damage.
Operating System Support
Currently tested operating system is MikroTik RouterOS starting from version v6.38
See www.routerboard.com for more information. Contact support@mikrotik.com 9-Jun-17
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter.
IMPORTANT: Exposure to Radio Frequency Radiation.
13 cm minimum distance has to be maintained between the antenna and the occupational user and 28 cm to general public. Under such
configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied.
Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in the United States (or
where FCC rules apply); only those antennas certified with the product are used. The use of any antenna other than those certified with the
product is expressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure the output power level of
antennas, according to country regulations and per antenna type. Professional installation is required of equipment with connectors to ensure
compliance with health and safety issues.
FCC ID numbers: TV7LHG5ACD, TV7LHG5ND, TV7LHG5NDM, TV7LHG5HPND
Industry Canada (IC: 7442A-LHG2ND)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
IC numbers: 7442A-LHG5ACD, 7442A-LHG5ND, 7442A-LHG5NDM, 7442A-LHG5HPND
See www.routerboard.com for more information. Contact 9-Jun-17support@mikrotik.com

Produkt Specifikationer

Mærke: Mikrotik
Kategori: Adgangspunkt
Model: LHG XL HP5

Har du brug for hjælp?

Hvis du har brug for hjælp til Mikrotik LHG XL HP5 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Adgangspunkt Mikrotik Manualer

Mikrotik

Mikrotik RouterBOARD hAP ac lite Manual

25 Juli 2025
Mikrotik

Mikrotik wAP 60G Manual

4 Juli 2025
Mikrotik

Mikrotik WAP R Manual

8 December 2024
Mikrotik

Mikrotik Cube Lite60 Manual

27 September 2024
Mikrotik

Mikrotik hAP ac² Manual

23 September 2024
Mikrotik

Mikrotik Audience LTE6 kit Manual

28 August 2024
Mikrotik

Mikrotik LtAP mini Manual

24 August 2024
Mikrotik

Mikrotik LHG XL HP5 Manual

13 August 2024
Mikrotik

Mikrotik HAP ac lite Manual

8 August 2024
Mikrotik

Mikrotik RBSXT2NDR2 Manual

5 August 2024

Adgangspunkt Manualer

Nyeste Adgangspunkt Manualer

Advantech

Advantech EKI-6333AC-2G Manual

30 Juli 2025
Advantech

Advantech EKI-6333AC-4GP Manual

30 Juli 2025
Advantech

Advantech EKI-1652WT Manual

29 Juli 2025
Advantech

Advantech EKI-6333AC-M12 Manual

29 Juli 2025
Advantech

Advantech EKI-9502G Manual

29 Juli 2025
AVM

AVM FRITZ!Powerline 1240 AX Manual

27 Juli 2025
TP-Link

TP-Link Omada Pro AP9778 Manual

25 Juli 2025
TRENDnet

TRENDnet TEW-825DAP Manual

25 Juli 2025
TRENDnet

TRENDnet TEW-925DAP Manual

25 Juli 2025
TP-Link

TP-Link Omada Pro AP9665 Manual

25 Juli 2025