Mosconi Gladen Pro 5/30 Manual

Mosconi Modtager Gladen Pro 5/30

Læs gratis den danske manual til Mosconi Gladen Pro 5/30 (1 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Mosconi Gladen Pro 5/30, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

PRO 5|30

4-channel AB class / 1-channel D amplifier [ Rev. 3.0 – 2017/10 ]

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

CEA-2006-A SPECIFICATIONS

POWER RATING :(@ 4 Ohm < 1% THD+N) 70Wx2 + 150Wx2 + 550Wx1

SN RATIO :(ref.: 1 Watt into 4 Ohm) >75 dBA (CH1/2) >71 (CH3/4) >73 (CH5)

SN RATIO Direct DSP :(ref.: 1 Watt into 4 Ohm) >83 dBA (CH1/2) >76 (CH3/4) >76 (CH5)

MOS SPECIFICATIONS (Tcase = 25 °C / 4 Ohm stereo / 0.2V input level @ 14.4 Volt if not otherwise specified)

TARGET POWER: 85x2 Watt (CH1/2), Watt (CH3/4), Watt (CH5) [@ 4 Ohm]170x2 600x1

REAL POWER ( ):

single section driven CH1/2: W W 95x2 @ 4 Ohm / 150 x2 @ 2 Ohm

1% THD [CH1/2/3/4] – 3% THD [CH5] CH3/4: W W 185x2 @ 4 Ohm / 290 x2 @ 2 Ohm

CH5: W W 660 @ 4 Ohm / 1030 @ 2 Ohm

REAL POWER ( ):

all sections driven 70x2 W (CH1/2) + W (CH3/4) + W (CH5)150x2 @ 4 Ohm 550x1 @ 4 Ohm

1% THD [CH1/2/3/4] – 3% THD [CH5] 65x2 W (CH1/2) + W (CH3/4) + W (CH5)135x2 @ 4 Ohm 760x1 @ 2 Ohm

W (CH1/2) + W (CH3/4) + W (CH5)85x2 195x2 @ 2 Ohm 750x1 @ 2 Ohm

Watt ( )1310 is the total amount of power the amplifier can deliver

THD (90% power rating ref.)

4 Ohm / ST mode < 0.045 % < 0.035 % < 1 % (CH1/2 - 1KHz) (CH3/4 - 1KHz) (CH5 - 100Hz)

2 Ohm / ST mode:< 0.05 % < 0.04 % < 1 % (CH1/2 - 1KHz) (CH3/4 - 1KHz) (CH5 - 100Hz)

DC-DC converter typology / Conversion frequency: Unregulated Push-Pull / 50 Khz (managed by microcontroller)

Supply voltage range operation: 9 V ÷ 16 V 11 V ÷ 14.4 V (Absolute maximum) / (Recommended)

Under / Over Voltage Safety Thresholds: 8 V 16 V(1 sec. 6V sustaining for Start & Stop) /

Mute delay time: 4 secs.

Secondary voltages (VDD#12 /VDD#34 /VDD#5 / DRIVE / SERV): ±33.1 V / ±45.3 V / ±84.7 V / ±14 V / ±15 V

Max output offset voltage (each channel): ±15 mV

Standby current: < 1 mA (typical)

Quiescent consumption @ 12V6 / 14V4: 1.90 A / 2.15 A (no idle current regutation)

Idle current regulation (no signal): 0.05 A (each trimmer)

Quiescent consumption @ 14V4: 2.25 A (with idle current setted)

Thermal protection consumption: 140 mA

Ground decoupling: (RCA Input) / 47R 1 KOhm (battery vs secondary) / (body vs battery)68 Ohm

Bandwidth (-3dB ÷ 1 Watt): < 5 Hz ÷ 135 KHz < 5 Hz ÷ 145 KHz < 5 Hz ÷ 1.75 KHz (CH1/2); (CH3/4); (CH5 10Watt)

Input sensitivity (Power rating ref): 0.35 V ÷ 12 V (5.3 V in DDSP mode) (3.1 V in DDSP mode) [CH1/2/3/4] 0.14 V ÷ 5.9 V [CH5]

Input impedance @ 1 KHz (STEREO input): 15 KOhm / 47 Ohm (LL) (HL)

S/N ratio – Power rating ref: (filter: 10 Hz - 500 KHz ) / (filter: 10 Hz - 22 KHz “A” weighted) 67 dB 94 dB

S/N ratio DDSP – Power rating ref: (filter: 10 Hz - 500 KHz ) / (filter: 10 Hz - 22 KHz “A” weighted) 69 dB 100 dB

Channel separation@ 100Hz / 1KHz / 10KHz – 10 Watt ref: 75 dB / 75 dB / 62 dB

Xover functions (selectable filters): CH1/2= HP: 43 ÷ 500Hz(x1) or 430 ÷ 5000Hz(x10) [12 dB/oct – Q: 0.7]

CH3/4= HP: 50 ÷ 200Hz & LP:(430 ÷ 5000Hz) [12 dB/oct – Q: 0.7]

CH5= LP: 43 ÷ 200Hz [24 dB/oct]

Special features: DDSP - Direct DSP (bypass all the preamplifier circuitry but the differential input interface)

HL/LL - High Level / Low Level selectable input

Controlled via uC – Internally controlled via Atmel Processor

Thermal cutoff Threshold: 90°C / 100°C (CH5 cutoff) (Overall cutoff) / (resume to normal operation)70°C

ProSPEED® Fan Controller Threshold: 50°C / 45°C / 70°C (start) (stop) (max speed)

Damping factor @ 100 Hz 10 Watt ref (Right / Left):- 319/397 318/487 153 [CH1/2] - [CH3/4] - [CH5]

Damping factor @ 1 KHz 10 Watt ref (Right / Left):- 291/375 304/453 101 [CH1/2] - [CH3/4] - [CH5]

Damping factor @ 10 KHz 10 Watt ref (Right / Left): - 178/199 183/219 n.a. [CH1/2] - [CH3/4] - [CH5]

Load drive limitations (*): 2 Ohm / 4 Ohm (Stereo / Bridged)

Suggested fuse: 150 A (Internal)

Size (mm): 500 / 205 / 55

Weight (Kg): 5.4

(*) VERY IMPORTANT NOTE - READ CAREFULLY

4 Ohm ST 8 Ohm BTL or – CONTINUOUS SINEWAVE SIGNAL – pure resistive load or speaker load

2 Ohm ST 4 Ohm BTL or – – pure resistive load or speaker loadMUSICAL SIGNAL

2 Ohm – – pure resistive load or speaker load (only CH5)MUSICAL SIGNAL

Produkt Specifikationer

Mærke:	Mosconi
Kategori:	Modtager
Model:	Gladen Pro 5/30

Har du brug for hjælp?

Hvis du har brug for hjælp til Mosconi Gladen Pro 5/30 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Mosconi Manualer

Mosconi Pico 8|10 DSP Manual

23 Februar 2025

Mosconi Gladen Pico 1 Manual

6 September 2024

Mosconi Gladen Pico 4 Manual

5 September 2024

Mosconi Gladen Pro 5/30 Manual

5 September 2024

Mosconi Gladen One 80.4 Manual

5 September 2024

Mosconi Gladen One 70.6 Manual

5 September 2024

Mosconi Gladen One 130.2 Manual

5 September 2024

Mosconi Gladen Pro 4/10 Manual

5 September 2024

Mosconi Gladen One 130.4 DSP Manual

5 September 2024

Mosconi Gladen One 130.4 Manual

5 September 2024

Modtager Manualer

Nyeste Modtager Manualer

3 Oktober 2025

3 Oktober 2025

2 Oktober 2025

2 Oktober 2025

Shinybow SB-3706SV Manual

1 Oktober 2025

August MR260 Manual

1 Oktober 2025

Inday HDDA-1 Manual

1 Oktober 2025

Inday HDDA-2 Manual

1 Oktober 2025

Shinybow SB-3702 Manual

1 Oktober 2025

Ground Zero GZCA 3000X.M1 Manual

1 Oktober 2025