Moultrie Pro Hunter II Manual

Moultrie Videokamera Pro Hunter II

Læs gratis den danske manual til Moultrie Pro Hunter II (3 sider) i kategorien Videokamera. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Moultrie Pro Hunter II, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Instructions for Pro Hunter II Feeder Kit

Thank you for your purchase of a Moultrie Pro Hunter II Feeder Kit. Please read this sheet before

operating the unit. If you should have any questions about this product or any other Moultrie product,

please contact us at . Allow us to better serve you by www.moultriefeeders.com/support

activating your 1-year warranty online at .http://www.moultriefeeders.com/warranty

If mounting the Moultrie Quick Lock Feeder Kit to:

• a Moultrie 30 or 55-gallon barrel* or Moultrie 6.5-gallon bucket, refer to .Section C

• a Moultrie 30-Gallon Quick-Lock Hopper, refer to . Section D

• any other containers, please visit our website at www.moultriefeeders.com

STOP

READ THIS FIRST

BEFORE

PROCEEDING

CONFIGURING AND TESTING FEEDER

FCC COMPLIANCE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For devices approved under Part 15, the user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user about changes or modications to the device (Section 15.21).

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

INSTALL BATTERY: Open Kit by removing wingnut located on the bottom and remove outer case. Install a 6-Volt Alkaline

(ex. Energizer™) or Moultrie rechargeable battery (MFHP12406) by attaching the Red Alligator Clip to the positive terminal

(+) and the Black Alligator Clip to the negative (-) terminal, making sure that the leads do not touch. Note: Make sure the

rubber protectors are around the gator clips after installation onto the battery. This helps protect the gator clips

from touching which can cause damage. We recommend using our Moultrie MFHP12406 6V 5ah battery.

CAUTION: DO NOT REVERSE POLARITY OF THE BATTERY LEADS. DO NOT LET THE BATTERY LEADS COME IN CONTACT WITH ONE ANOTHER WHILE CONNECTED

A BATTERY. THIS CAN CAUSE PERSONAL INJURY OR PROPERTY DAMAGE. IN NO EVENT SHALL PRADCO BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE,

INCIDENTAL,

SPECIAL CONSEQUENTIAL DAMAGES, TO PROPERTY OR LIFE, WHATSOEVER ARISING OUT OF OR CONNECTED WITH THE USE OR MISUSE OF THIS

PRODUCT. YOUR USE OF THIS PRODUCT IS AT YOUR OWN RISK.

SET CURRENT TIME: Press the PROGRAM button and SET CURRENT TIME will appear. Press UP or DOWN to set the

hour, then press RIGHT to go to the minutes. Press UP or DOWN to set the minutes. Press the BACK button to return

to the Main Menu , or press PROGRAM to proceed through the settings.

NOTE: The timer is capable up to 10 feed times, each 1-60 seconds each, and each can operate on any day of

the week where each day can be toggled ON/OFF.

SET CURRENT DAY: Press the PROGRAM button until the Set Current Day screen appears. Press LEFT or RIGHT to

select the current day. Press BACK to return to the Main Menu, or press PROGRAM to proceed through the settings.

SET EST. FEED REMAINING: Press the PROGRAM button until the Est. Feed Remaining screen appears. Press UP or

DOWN to select the amount of feed you have in the feeder. Press BACK to return to the Main Menu, or press

PROGRAM to proceed through the settings.

SET FEED TIME: Press the PROGRAM button until the desired Feed Timer appears at the top of the screen. Press the

DOWN button until the feed time is ashing. Press PROGRAM to enter edit mode. Press UP or DOWN to set the hour.

Press the RIGHT button to go over to the minutes. Press UP or DOWN to set the minutes. Press PROGRAM or BACK to

return to the Feed Timer. The factory settings include two feeder times 7am and 6pm, each for 6 seconds.

SET DAYS OF THE WEEK: After setting the feed time, press UP so the days of the week start ashing. Press PROGRAM

to enter edit mode. By default all days should be enabled. Press LEFT or RIGHT to highlight the desired day. Press

DOWN to disable the selected day. Press UP to re-enable the selected day. Once all desired days are selected, press

PROGRAM or BACK to return to the Feed Timer.

SET RUN DURATION: Press DOWN and LEFT until the RUN DURATION seconds are ashing. Press PROGRAM to enter

edit mode. Press UP or DOWN to set desired feed duration. Press PROGRAM or BACK to return to the Feed Timer. 

SET MOTOR SPEED: Press UP or DOWN until the motor speed setting is ashing at the bottom of the screen. Press

PROGRAM to enter edit mode. Press RIGHT or LEFT to select the desired motor setting. Press PROGRAM or BACK to

return to the Feed Timer.

When the Feed Timer is blinking at the top of the screen, press PROGRAM or RIGHT to advance to the next feed

timer. Repeat for all required feed times.

TEST FEEDER: Press the BACK button to reach the Main Menu. Press the TEST button to enter the Test Mode. The

Test duration will appear (this will be the same as the duration as Feed Timer 1). Press UP or DOWN to set the Test

Duration. Press PROGRAM. Press RIGHT or LEFT to select desired motor speed. Press PROGRAM to perform test.

After a 5 second countdown, the test will commence. 

Full Battery

Empty Battery

ALIGN LUGS AND

L-SLOTS

DO NOT EXCEED 400 LBS

OF FEED IN 55-GAL FEEDERS

Quick-Lock

Feeder Kit

Quick-Lock

Adapter

NOTE: DO NOT LOAD FEEDER until it is standing up and in place (see Section D-4).

Belly Band

Ring

Bolt

Spacer

Lock

Washer

Nut

DO NOT EXCEED 200 LBS

OF FEED IN 30-GAL FEEDERS

Belly Band

Ring

ASSEMBLE WITH MOULTRIE QUICK-LOCK ADAPTER

55-Gallon or 30-Gallon Barrel*

Assemble by snapping in place as shown. Quick-Lock adapter bolt tabs

Turn the upside down and slide the metal drum belly band ring

around perimeter and make sure that belly band is snug against

the bottom structure ring as shown (Moultrie barrel only).

Slide the bolt through the , and belly band ring spacer

lock washer as shown. Tighten nut on bolt until metal

belly band ring tabs are touching spacer on each side.

Mount Quick-Lock adapter using (3) 1/4” x 1” bolts, nuts and

washers provided in the pre-drilled holes (Moultrie barrel only).

Or use the Quick-Lock adapter as a template to mark and drill

the mounting holes (non-Moultrie barrel).

Connect Quick-Lock feeder kit to assembled adapter as shown.

*Can also be used on a 6.5-gallon bucket.

Assembled

Quick-Lock

Adapter

Bolt Tabs

ADJUSTING FUNNEL HEIGHT

Once the funnel is in desired position,

retighten the screw with Phillips-head

screwdriver. Do not overtighten.

To adjust funnel height:

With a Phillips-head screwdriver,

loosen screw.

With screw loosened, use tabs to position funnel

in one of the two positions by either pushing

down or up depending on desired position.

Produkt Specifikationer

Mærke:	Moultrie
Kategori:	Videokamera
Model:	Pro Hunter II

Har du brug for hjælp?

Hvis du har brug for hjælp til Moultrie Pro Hunter II stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Videokamera Moultrie Manualer

Moultrie Reaction Cam Manual

17 Juni 2025

Moultrie Quick-Lock Feeder Kit Manual

5 September 2024

Moultrie Super Pro Magnum Feeder Manual

5 September 2024

Moultrie Deer Feeder 325 Manual

5 September 2024

Moultrie Pro Hunter II Manual

1 September 2024

Videokamera Manualer

Nyeste Videokamera Manualer

Sony DCR-DVD408 Manual

13 August 2025

Sony HDR-AX2000 Manual

13 August 2025

Rollei Actioncam 10s Plus Manual

11 August 2025

Rollei Actioncam 40s Pro Manual

11 August 2025

Samsung SCL860 Manual

11 August 2025

Rollei Actioncam 5s Plus Manual

10 August 2025

Samsung SCD303 Manual

10 August 2025

Rollei Actioncam 11s Plus Manual

10 August 2025

Konica-Minolta XM Manual

10 August 2025

Samsung SCD250 Manual

10 August 2025