Naim NAP 200 Manual

Naim Modtager NAP 200

Læs gratis den danske manual til Naim NAP 200 (44 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Naim NAP 200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/44

o w n e r s m a n u a L

P r e a m P L I F I e r s

I n T e G r a T e D a m P L I F I e r s , P o w e r a m P L I F I e r s

e n G L I s H D e u T s C H F r a n Ç a I s I T a L I a n o

SAFETY INSTRUCTIONS

In order to comply with current European safety regulations

it is essential that the Naim loudspeaker connectors

supplied with ampliﬁers and loudspeakers are used.

Do not under any circumstances allow anyone to modify

your Naim equipment without ﬁrst checking with the factory,

your retailer, or your distributor. Unauthorised modiﬁcations

will invalidate your guarantee.

Equipment must not be exposed to dripping or splashing

and no objects ﬁlled with liquid, such as vases, should be

placed on the equipment.

For your own safety do not under any circumstances open

Naim equipment without ﬁrst disconnecting it from the

mains.

Warning: an apparatus with CLASS I construction shall

be connected to a mains socket outlet with a protective

earthing connection.

Where the mains plug or an appliance coupler is used as

the disconnect device, the disconnect device shall remain

readily operable. To disconnect the equipment from the

mains remove the mains plug from the mains outlet.

The following label is attached to all mains powered

equipment:

NOTE

This equipment has been tested and found to comply

with the relevant EMC and Safety Standards, and, where

applicable, also complies with the limits for a class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio

frequency and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or

television reception, which can be determined by turning

oﬀ and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult your Naim retailer or an experienced radio/TV

technician for help.

W A R N I N G

THIS APPARATUS

MUST BE EARTHED

Page Section

E1 1 Connections

E1 2 Mains Power

E2 3 General Installation

E3 4 NAC 552 Introduction and Installation

E4 5 NAC 552 Controls and Connections

E5 6 NAC 552 Speciﬁcation

E6 7 NAC 252 Introduction and Installation

E6 8 NAC 252 Controls and Connections

E7 9 NAC 252 Speciﬁcation

E8 10 NAC 282 Introduction and Installation

E8 11 NAC 282 Controls and Connections

E10 12 NAC 282 Speciﬁcation

E11 13 NAC 202 Introduction and Installation

E11 14 NAC 202 Controls and Connections

E12 15 NAC 202 Speciﬁcation

E13 16 NAC 152 XS Introduction and Installation

E14 17 NAC 152 XS Controls and Connections

E16 18 NAC 152 XS Speciﬁcation

E17 19 Supernait Introduction and Installation

E19 20 Supernait Controls and Connections

E21 21 Supernait Speciﬁcation

E22 22 Nait XS Introduction and Installation

E23 23 Nait XS Controls and Connections

E25 24 Nait XS Speciﬁcation

E26 25 Nait 5 Introduction and Installationi

E26 26 Nait 5 Controls and Connectionsi

E27 27 Nait 5 Speciﬁcationi

E28 28 Preampliﬁer and Integrated Ampliﬁer

Operation

E31 29 R-com Remote Handset

E32 30 NARCOM 4 Remote Handset

E33 31 NAP 500 Installation and Operation

E34 32 NAP 500 Connections

E34 33 NAP 500 Speciﬁcation

E35 34 NAP 300 Installation and Operation

E36 35 NAP 300 Connections

E36 36 NAP 300 Speciﬁcation

E37 37 NAP 250 Installation and Operation

E37 38 NAP 250 Connections

E37 39 NAP 250 Speciﬁcation

E38 40 NAPV 145 Installation and Operation

E38 41 NAPV 145 Connections

E38 42 NAPV 145 Specification

E39 43 NAP 200 Installation and Operation

E39 44 NAP 200 Connections

E39 45 NAP 200 Speciﬁcation

E40 46 NAP 155 XS Installation and Operation

E40 47 NAP 155 XS Connections

E40 48 NAP 155 XS Speciﬁcation

E41 49 NAPV 175 Installation and Operation

E41 50 NAPV 175 Connections

E42 51 NAPV 175 Specification

E42 52 Declarations of Conformity

C o n t e n t s

Produkt Specifikationer

Mærke:	Naim
Kategori:	Modtager
Model:	NAP 200
Vekselstrømsindgangsspænding:	100-230 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Bredde:	432 mm
Dybde:	314 mm
Højde:	87 mm
Vægt:	11600 g
Produktfarve:	Sort
Frekvensområde:	3 - 50000 Hz
Forbindelsesteknologi:	Ledningsført
Lyd-output kanaler:	2.0 kanaler
Formål:	Hjem
Lyd (L, R) udgang:	2
klirfaktor (THD):	- %
Signal/støjforhold:	- dB
Spidseffekt pr. kanal:	70 W
Højttalere tilslutningstype:	Bananstik
Indgangsimpedans:	18000 ohm (Ω)
RMS udgangseffekt pr. kanal (8 ohm):	70 W