NuTone CP2OHAB Manual

NuTone Dørklokke CP2OHAB

Læs gratis den danske manual til NuTone CP2OHAB (4 sider) i kategorien Dørklokke. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om NuTone CP2OHAB, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
D) Doors vary in thickness depending on the manufacturer. At
the edge of the door, measure the thickness of the door. Then,
determine the distance to the center to the edge of the door
(half the thickness of the door). Using the awl (or nail), mark
a point on the edge of the door where the centerline pencil
mark (from Step 1C) and the center of the edge of the door
meet (half the thickness), see .Figure #3
Step 2
Drill the Door
A) Using the 2-1/8” hole saw, drill the cross bore hole centered
on the mark made on the face of the door from Step 1B. See
Figure #3 Important:. To avoid splintering or marring the
door, drill from one side of the door until the pilot bit comes
through the door. Then nish drilling from the other side of
the door, using the hole made by the pilot bit as your guide
until the cross bore hole is complete.
B) Using the 1” bit, drill the edge bore hole centered on the mark
made on the edge of the door where the centerline and center
thickness met from Step 1D, see Figure #3 Important:.
Make sure that you drill a full 3-1/2” deep, to accommodate
the overall length of the 2-3/8” latch. If you are using a 2-3/4”
backset latch, then the overall depth must be at least 3-3/4”.
v
v
v
v
&ORv"ACKSET
&ORv"ACKSET
#ROSS"ORE
(OLEv
$IAMETER
-ARKFROM
3TEP"
%DGE"ORE
(OLEv
$IAMETER
-ARKFROM
3TEP$
$OOR4HICKNESS
&ACEPLATE
-ORTISE
!REA
#ENTERLINE
-ARKFROM
3TEP#
-INIMUM
 TOCENTERv
LINEOFDOOR
KNOBCROSS
BOREHOLE
Door Hardware
Installation Instructions
Rosette Passage and Privacy
Carefully unpackage all components and place them within easy
reach. Find on Page 4 of these instructions for a listing Figure #1
and drawing of each component. Detach and place Figure #1
beside the components for easy reference. Check your door to see
if it has been prepped (pre-drilled) for installing a lock. If your
door has already been prepped for installation, start at Step 4. If
your door has not been prepped for installation, you will need a
#2 Phillips screwdriver, a drill, a 2-1/8” hole saw, a 7/64” drill bit,
a 1” drill bit, chisel, pencil, tape and an awl (or nail).
Step 1
Mark the Door
A) Locate the Door Preparation Template that is included with
the instructions. Fold the template along the “edge-of-door”
line. : Before positioning the template, make sure Important
that you are aligning it on the . non-hinged edge of the door
Carefully position the template so that the narrow portion
of the template wraps around the edge of the door, and the
large portion of the template remains on the face of the door,
see . The centerline indicates the center of where Figure #2
the knob or lever will be located. Slide the template up or
down on your door so that the horizontal centerline is located
at a height that is both comfortable to use and attractive in
appearance. Typically this will be approximately 36”-38”
from the oor, see Figure #2. Once you have chosen the
height, tape the template to the door.
B) The backset is the distance from the edge of the door to
the center of the rosette. Standard backsets are 2-3/8” and
2-3/4”. Determine the backset of your latch (Part #5), by
checking the marking on the latch itself (if marked, it will say
2-3/8” or 2-3/4”). If the latch is not marked, measure the latch
between points A and B to determine the backset, as shown
in Figure #2. Once you know your backset, nd the point on
the template where the centerline crosses the vertical line that
corresponds with the correct backset. Using the awl (or nail)
mark this point, making sure that it is marked well enough to
see on the door once the template is removed.
C) Follow the centerline around the edge of the door and using
a pencil, extend the centerline onto the edge of the door. The
mark should be parallel to the oor. Once this mark is made,
you may remove the template from the door. Page 1 - PK143
For
Assistance
Call:
1-800-522-7336
8 am - 5 pm, Monday - Friday, MST
(A) (B)
Template
Edge
of
Door
Face of Door
Centerline
Latch
Backset
Measurement
2-3/8” or 2-3/4”
Figure #2
Figure #3
Anti-
Rotation
Block
Latch
Tongue
Star Shaped
Hub
Inside Face of Door
Threaded
Privacy Pin
Hole
C) Determine which direction the door will swing when it is
being opened. Rotate the latch tongue so that the at edge of
the tongue faces toward the direction the door swings when
being opened (and the round edge towards the doorjamb).
Once oriented correctly, install the faceplate (Part #7) over the
latch tongue (Part #5a), locking the latch tongue orientation.
Fasten in place using two 1” wood screws (Part #8) Hint:
Coating the screw threads with a small amount of soap (liquid
or bar soap) will make installation easier.
Step 5
Install the Trim
A) Using for reference, gather together the trim half A Figure #1
(Part #1), trim half B (Part #2), 1-1/2″ rosette machine screws
(Part #3), and Phillips screwdriver.
B) Find trim half A (Part #1). Place trim half A on the outside of
the door, such that the spindle is inserted into the star-shaped
hub of the latch and the screw bosses are nested in the top and
bottom slots in the anti-rotation block, see . Figure #5 Lever
designs only: If installing a lever, see for correct Figure #6
orientation of lever on the door. If your lever is oriented
incorrectly, move it to the other side of the door so it matches
the correct orientation in , before proceeding with Figure #6
installation. Make sure that the Privacy function only:
privacy hole in the rose is oriented so that it is closest to the
edge of the door where the latch tongue sticks out.
Correct Lever Orientation
(Lever Rotates Downward)
Incorrect Lever Orientation
To correct, remove from door and
mount on opposite door face
Door
Edge
Step 3
Mortise for the Faceplate
A) Using Figure #1 for reference, nd the faceplate (Part
#7). On the edge of the door, center the faceplate over the
newly drilled edge bore hole, so that the D-shaped hole in
the faceplate is centered over the 1” edge bore hole. Align
it so that the edges are parallel to the edges of the door and
roughly centered side-to-side. Mark around the faceplate with
a pencil and remove from door.
B) Using the chisel, score the outline of the faceplate. Next,
chisel away the material within the outline to a depth of 1/8”.
When you are done, you should be able to insert the latch
(part #5), place the faceplate over the latch tongue (Part #5a),
and have the faceplate be ush with the edge of the door.
C) Again, using the faceplate as a template and the awl as a
marking tool, mark for the two screws holes that will hold the
faceplate on the door. Remove the faceplate from the door to
avoid marring the nish. Then, drill the two screw holes using
a 7/64” drill bit. Make sure the holes are drilled at least 1”
deep. Having too small or too shallow of a hole can cause the
screws to shear off.
Installing Your Lock
Step 4
Install the Latch
A) Once your door is prepped for installation, you will need a #2
Phillips screwdriver for the installation of your latch.
B) Locate the latch (Part #5) and the anti-rotation block (Part
#4). Insert the anti-rotation block in the cross bore hole so
that the arrow on the block is pointing toward the edge of the
door. Install the latch in the edge bore hole, making sure that
it is correctly inserted through the anti-rotation block. When
installed correctly, the star-shaped hub in the latch should be
centered in the hole of the anti-rotation block, see Figure #4.
Privacy function only: The privacy latch must be inserted
into the door so that the locking mechanism (threaded privacy
pin hole - Part #5b) is facing the inside of the door, see
Figure #1.
Page 2 - PK143
Figure #4
Figure #5
Figure #6

Produkt Specifikationer

Mærke: NuTone
Kategori: Dørklokke
Model: CP2OHAB

Har du brug for hjælp?

Hvis du har brug for hjælp til NuTone CP2OHAB stil et spørgsmål nedenfor, og andre brugere vil svare dig


Dørklokke NuTone Manualer

NuTone

NuTone LA11BG Manual

9 Juli 2025
NuTone

NuTone LA305WL Manual

30 Marts 2025
NuTone

NuTone BK131LWH Manual

30 Marts 2025
NuTone

NuTone LA130WH Manual

30 Marts 2025
NuTone

NuTone BK144LCL Manual

30 Marts 2025
NuTone

NuTone LA223WH Manual

3 September 2024
NuTone

NuTone LA224RWH Manual

3 September 2024
NuTone

NuTone LA226WH Manual

3 September 2024
NuTone

NuTone BKL340KWH Manual

3 September 2024
NuTone

NuTone LA227WH Manual

3 September 2024

Dørklokke Manualer

Nyeste Dørklokke Manualer

Emos

Emos P5723T Manual

1 August 2025
Emos

Emos P5733W Manual

31 Juli 2025
Elro

Elro DB4000 Manual

31 Juli 2025
Cata

Cata LFK 6001 X Manual

24 Juli 2025
Gira

Gira 2559 20 Manual

23 Juli 2025
Gira

Gira 2551 20 Manual

22 Juli 2025
Gira

Gira 2556 20 Manual

22 Juli 2025
Homematic IP

Homematic IP HmIP-DBB Manual

17 Juli 2025
Infiniton

Infiniton CMPE-64WBM Manual

16 Juli 2025
Avidsen

Avidsen Bamboo Plus Manual

15 Juli 2025