Nxg NX-W6.2-P Manual

Nxg Højttaler NX-W6.2-P

Læs gratis den danske manual til Nxg NX-W6.2-P (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Nxg NX-W6.2-P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

(Continued on reverse)

Where To Place Your In-Wall Speakers

Placement can make all the difference in how your speakers sound, and how easy they will be to

install. Carefully consider where your speakers should be positioned. For optimum performance,

speakers should be mounted to the left and right of the main listening position and a minimum of 8

to 10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities containing electrical wiring,

heating ducts, water pipes, etc. Make sure the wall or ceiling materials are sturdy enough to sup-

port the weight of the speakers.

In-Wall Placement: Optimum performance will be achieved when your speakers are mounted at

ear level or slightly higher. If you desire to mount them higher in the wall, turn the speaker over so

the tweeter is closer to the listening area.

In-Ceiling Placement: Optimum performance will be achieved when your speakers are mounted

to the left and right of the main listing area.

Pivoting Tweeters (Fig. 3)

The tweeters in all NXG Pro Series speakers may be adjusted, allowing you to tailor the speaker to

better fit the listening area. The overall smoothest response is achieved with the tweeter facing

straight out: however, you may find the sound more pleasing by aiming tweeters toward a particular

listening area. To adjust the tweeter, apply pressure on the ring surrounding the tweeter with your

thumb or finger.

Tweeter Level Adjustment (Fig. 3)

The level switch allows you to tailor the speakers’ frequency response to better match the room’s

acoustics. As an example, if a room has a hardwood floor, which makes it acoustically brighter

sounding, you may want to turn the tweeter level down. You can experiment with the levels to find

the sound that’s most pleasing to you in your particular listening environment.

Speaker Installation In Existing Construction (See Fig. 4 on reverse)

Once you have selected the location for your speakers, you are ready to install them.

You will need the following:

• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers

• Pencil • Utility Knife or Drywall Saw • Small Level

• Masking Tape • Phillips Screwdriver • Speaker Wire

NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer or

custom audio contractor.

1. NXG Architectural Speakers are designed to be installed in the wall area between studs. Using a

stud finder, make sure you are between two studs. Using the supplied template and a level to

ensure your template is straight, trace around the outside with a pencil.

2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of the

outline. This will allow you to check for any obstructions that may exist behind the desired location.

CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in the planned

installation areas prior to drilling or cutting the wall.

3. Run speaker wire from your amplifier or speaker switching device to the speaker location.

4. Carefully remove the grille and inner grille backing. (Note: The open cell foam inner grille backing

is designed to hide speaker components from view and may be removed if desired.) If you like the

standard white finish of your NXG speakers, skip to step 5, but if if you want your speakers to blend

in with a colored wall or ceiling, now is the time to paint your speaker’s outer frame and perforated

grille. (Remove the foam inner grille backing and put it aside in a clean and dust free area for later

Congratulations on choosing NXG

In-Wall Loudspeakers. Like all NXG

products, great care has been taken

in their design. Their combination of

advanced engineering and state-of-

the-art materials will provide you with

years of listening pleasure, while

blending smoothly into your home’s

decor. Before you get started, it is a

good idea to identify all the parts and

hardware (See Fig. 1).

FIG. 3

Press on the edge of

the tweeter to rotate

FIG. 2

Adjust tweeter level

by setting switch

IR sensor knockout

Speaker with self-contained

mounting clamps

Aluminum grille with

foam inner backing

NX-W6.2-P 61/2˝ Two-Way In-Wall Speaker System

FIG. 1

Grille

removal

tool

Black

grille

adhesive

Tweeter Level Switch

Painting masks

Cutout templates

NXG Pro Series In-Wall Speakers can be used as

rear surround sound channels by placing

them (1) behind, (2) on each side of viewer,

or (3) in the ceiling just behind viewing

position. They also make excellent front

channel home theater speakers (4).

Produkt Specifikationer

Mærke:	Nxg
Kategori:	Højttaler
Model:	NX-W6.2-P

Har du brug for hjælp?

Hvis du har brug for hjælp til Nxg NX-W6.2-P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Nxg Manualer

Nxg NX-W5.2-LCR-P Manual

21 August 2024

Nxg NX-W6.2-P Manual

20 August 2024

Nxg NX-C6.2-P Manual

20 August 2024

Nxg Onyx NX-C8.2-ENC-X Manual

19 August 2024

Nxg NX-C8.3-P Manual

18 August 2024

Nxg NX-C8.2-P Manual

18 August 2024

Nxg NX-AW5 Manual

10 Juli 2024

Højttaler Manualer

Nyeste Højttaler Manualer

RetroSound R-507N Manual

29 Oktober 2025

TDK TP6803BLK Manual

28 Oktober 2025

TDK TREK Flex A28 Manual

28 Oktober 2025

Altec Lansing inMotion iM4 Manual

24 Oktober 2025

Vonyx VX822 Manual

21 Oktober 2025

Memphis Audio SRX42 Manual

19 Oktober 2025

Memphis Audio MS62 Manual

19 Oktober 2025

Madison MAD-CENTER120 Manual

19 Oktober 2025

Goji Mini GMINIG17 Manual

19 Oktober 2025

Audison VOCE AV 12 Manual

19 Oktober 2025