Nxg Onyx NX-C8.2-ENC-X Manual

Nxg Højttaler Onyx NX-C8.2-ENC-X

Læs gratis den danske manual til Nxg Onyx NX-C8.2-ENC-X (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Nxg Onyx NX-C8.2-ENC-X, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
NX-C8.2-ENC-X 8˝ Two-Way In-Ceiling Enclosed Speaker System
Where To Place Your In-Ceiling Speakers
Placement can make all the difference in how your speakers sound, and how easy they will be to
install. Carefully consider where your speakers should be positioned. For optimum performance,
speakers should be mounted to the left and right of the main listening area and a minimum of 8
to 10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities containing electrical wiring,
heating ducts, water pipes, etc. Make sure the ceiling materials are sturdy enough to support the
weight of the speakers.
Adjustable Tweeters (Fig. 3)
The tweeter in your NXG speaker may be adjusted, allowing you to tailor the speaker to better fit
the listening area. The overall smoothest response is achieved with the tweeter facing straight out:
however, you may find the sound more pleasing by aiming tweeters toward a particular listening
area. To adjust the tweeter, grasp the outside of the tweeter plate and gently pivot it toward the
listening area.
Speaker Installation In Existing Construction (See Fig. 4 on reverse)
Once you have selected the location for your speakers, you are ready to install them.
You will need the following:
• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers • Speaker Wire
• Pencil • Masking Tape Phillips Screwdriver • Utility Knife or Drywall Saw •
NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer or
custom audio contractor.
1. NXG Architectural Speakers are designed to be installed in the ceiling or wall area between studs.
Using a stud finder, make sure you are between two studs. Tape the supplied template to the wall
and lightly trace around the inside with a pencil.
2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of the
outline. This will allow you to check for any obstructions that may exist behind the desired location.
CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in the planned
installation areas prior to drilling or cutting the wall.
3. Run speaker wire from your amplifier or speaker switching device to the speaker location.
4. Carefully remove the grille and inner grille backing. (Note: The open cell foam inner grille backing
is designed to hide speaker components from view and may be removed if desired.) If you like the
standard white finish of your NXG speakers, skip to step 5, but if if you want your speakers to blend
in with a colored wall or ceiling, now is the time to paint your speaker’s outer frame and perforated
grille. (Remove the foam inner grille backing and put it aside in a clean and dust free area for later
reinstallation if desired.) The speaker’s outer surface will accept ordinary latex wall paint or aerosol
spray paint. Because the speaker baffle surface behind the grille should remain unpainted, you will
need to cover this area with the supplied cardboard paint mask. Cover the speaker’s interior black
surface, woofer and tweeter. Paint the outer speaker frame and grille separately. (Grille painting hint:
Use a paint roller that is nearly out of paint to first paint the inside of the grille, then the outside. This
will avoid paint filling the grille perforations.)
Congratulations on choosing NXG In-Ceiling
Loudspeakers. Like all NXG products, great
care has been taken in their design. Their
combination of advanced engineering and
state-of-the-art materials will provide you with
years of listening pleasure, while blending
smoothly into your home’s decor. Before you
get started, it is a good idea to identify all the
parts and hardware (See Fig. 1).
FIG. 1
FIG. 2
NXG ceiling speakers can be used as rear
surround channels by mounting them
(1) on each side of, (2) just behind, or
(3) in back of the viewing position.
1
1
2
2
3
3
FIG. 3
OWNER’S MANUAL
(Continued on reverse)
Speaker with self-contained
mounting clamps
Metal grille with foam
inner grille cover
Black
grille
adhesive
Cutout
template
Painting mask
Pivoting
tweeter
Grille
removal
tool

Produkt Specifikationer

Mærke: Nxg
Kategori: Højttaler
Model: Onyx NX-C8.2-ENC-X

Har du brug for hjælp?

Hvis du har brug for hjælp til Nxg Onyx NX-C8.2-ENC-X stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Nxg Manualer

Nxg

Nxg NX-W5.2-LCR-P Manual

21 August 2024
Nxg

Nxg NX-W6.2-P Manual

20 August 2024
Nxg

Nxg NX-C6.2-P Manual

20 August 2024
Nxg

Nxg Onyx NX-C8.2-ENC-X Manual

19 August 2024
Nxg

Nxg NX-C8.3-P Manual

18 August 2024
Nxg

Nxg NX-C8.2-P Manual

18 August 2024
Nxg

Nxg NX-AW5 Manual

10 Juli 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Cicada Audio

Cicada Audio CHX65.2 Manual

31 Oktober 2025
RetroSound

RetroSound VW-BUS65 Manual

31 Oktober 2025
Bigben

Bigben PARTYBTBALL Manual

31 Oktober 2025
Wet Sounds

Wet Sounds REV10 SE Manual

30 Oktober 2025
RetroSound

RetroSound R-507N Manual

29 Oktober 2025
TDK

TDK TP6803BLK Manual

28 Oktober 2025
TDK

TDK TREK Flex A28 Manual

28 Oktober 2025
Altec Lansing

Altec Lansing inMotion iM4 Manual

24 Oktober 2025
Vonyx

Vonyx VX822 Manual

21 Oktober 2025
Memphis Audio

Memphis Audio SRX42 Manual

19 Oktober 2025