Nxg NX-W5.2-LCR-P Manual

Nxg Højttaler NX-W5.2-LCR-P

Læs gratis den danske manual til Nxg NX-W5.2-LCR-P (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Nxg NX-W5.2-LCR-P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Where To Place Your In-Wall Speakers

Placement can make all the difference in how your speakers sound, and how easy they will be

to install. Carefully consider where your speakers should be positioned. For optimum perform-

ance in a center-channel application, speaker should be mounted directly above or below TV

or monitor. For optimum performance when used in right and left main listening positions,

speakers should be mounted to the left and right of the main listening position and a minimum

of 8 to 10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities containing electrical

wiring, heating ducts, water pipes, etc. Make sure the wall or ceiling materials are sturdy enough

to support the weight of the speakers.

Note: When the NX-W5.2-LCR-P is mounted horizontally in a center-channel application, modifi-

cation may need to be made to the stud cavity to accommodate speaker.

Pivoting Tweeter (Fig. 3)

The tweeter in the NX-W5.2-LCR-P speaker may be adjusted, allowing you to tailor the speaker

to better fit the listening area. The overall smoothest response is achieved with the tweeter fac-

ing straight out: however, you may find the sound more pleasing by aiming the tweeter toward

a particular listening area. To adjust the tweeter angle, apply pressure on the ring surrounding

the tweeter with your thumb or finger.

Tweeter Level Adjustments (Fig. 4)

The tweeter level control allows you to tailor the speakers’ frequency response to better match

the room’s acoustics. As an example, if a room has a hardwood floor, which makes it acoustical-

ly brighter sounding, you may want to adjust the tweeter level down to compensate. You can

experiment to find the sound that’ most pleasing to you in your particular listening environment. s

Speaker Installation In Existing Construction (See Fig. 5)

Once you have selected the location for your speakers, you are ready to install them.

You will need the following:

• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers

• Pencil • Utility Knife or Drywall Saw • Small Level

• Masking Tape • Phillips Screwdriver • Speaker Wire

NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer

or custom audio contractor.

1. NXG Architectural Speakers are designed to be installed in the wall area between studs.

Using a stud finder, make sure you are between two studs. Using the supplied template and a

level to ensure your template is straight, tape the template to the wall and lightly trace around the

inside with a pencil.

2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of

the outline. This will allow you to check for any obstructions that may exist behind the desired

location. CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in

the planned installation areas prior to drilling or cutting the wall.

3. Run speaker wire from your amplifier or speaker switching device to the speaker location.

4. Remove the grille from the speaker. If you like the standard white finish of your NXG In-Wall

Speakers, skip to step 5, but if if you want your speakers to blend in with a colored wall, now is

the time to paint your speakers outer frames and perforated grilles. The speakers outer surfaces

will accept ordinary latex wall paint or aerosol spray paint. Because the surface behind the grille

should remain unpainted, you will need to cover this area. Cover the speaker’s interior black

surface, woofer and tweeter. Paint the outer speaker frame and grille separately.

5. Attach the wire to the input terminals on the rear of the speaker. Remember to maintain

proper polarity with the amplifier by attaching the positive (+) lead to the red terminal and the

negative (-) lead to the black terminal.

Congratulations on choosing NXG In-Wall Loudspeakers. Like all NXG products, great care has

been taken in their design. Their combination of advanced engineering and state-of-the-art mate-

rials will provide you with years of listening pleasure, while blending smoothly into your home’s

decor. Before you get started, it is a good idea to identify all the parts and hardware (See Fig. 1).

FIG. 2

FIG. 3

Press on the

outer edge

of the tweeter

rim to rotate

NX-W5.2-LCR-P Video-Shielded Center/Left/Right In-Wall

Home Theater Speaker System

(Continued on reverse)

NXG In-Wall Speakers can be used as rear

surround sound channels by placing them (1) behind,

(2) on each side of viewer, or (3) as front main

home theater speakers. They also can be mounted

horizontally for a center-channel application (4).

Adjust

tweeter level

as shown

FIG. 4

FIG. 1

Speaker with

self-contained

mounting clamps

Cutout Template

Aluminum Grille with

foam inner backing

Grille

removal

tool

Black

grille

adhesive

Painting Mask

IR Sensor

Knockout

Tweeter Level Switch

Produkt Specifikationer

Mærke:	Nxg
Kategori:	Højttaler
Model:	NX-W5.2-LCR-P

Har du brug for hjælp?

Hvis du har brug for hjælp til Nxg NX-W5.2-LCR-P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Nxg Manualer

Nxg NX-W5.2-LCR-P Manual

21 August 2024

Nxg NX-W6.2-P Manual

20 August 2024

Nxg NX-C6.2-P Manual

20 August 2024

Nxg Onyx NX-C8.2-ENC-X Manual

19 August 2024

Nxg NX-C8.3-P Manual

18 August 2024

Nxg NX-C8.2-P Manual

18 August 2024

Nxg NX-AW5 Manual

10 Juli 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Trust Almo 2.0 22915 Manual

5 November 2025

Trust Orada 25878 Manual

4 November 2025

DS18 PRO-SDF6R Manual

4 November 2025

DS18 35D200NO-4 Manual

4 November 2025

DS18 6PRO600SE-8 Manual

4 November 2025

Lenco BTC-020 Manual

4 November 2025

W-KING T9-2 Manual

4 November 2025

Orava Capella-1B Manual

4 November 2025

Victrola Willow VRS-2800 Manual

3 November 2025

Hama Bomb 3.0 00188234 Manual

3 November 2025