Ozito TBS-254 Manual

Ozito Sav TBS-254

Læs gratis den danske manual til Ozito TBS-254 (10 sider) i kategorien Sav. Denne vejledning er vurderet som hjælpsom af 65 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 33 anmeldelser. Har du et spørgsmål om Ozito TBS-254, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/10
ASSEMBLING THE DIAL
TABLE SAW
2000W 254mm
ASSEMBLY MANUAL
PARTS
FASTENERS
TBS-254
5 Spanner 10mm/Pin 6 Spanner 10/12mm
1 Bevel Adjustment Dial
2 Height Adjustment Handle
3 Blade guard
4 Riving Knife
5 Rubber Feet x 4
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
WARNING!
BEFORE ASSEMBLING YOUR TABLE SAW OR
REPLACING BLADES, MAKE SURE THAT THE MOTOR IS
OFF AND THE TOOL IS DISCONNECTED FROM THE POWER
SUPPLY TO PREVENT ACCIDENTAL STARTING.
5 Remove any cardboard boxes
from behind the motor; it can
be easily accessed by tilting the
blade using the Blade Bevel
Adjustment.
3 Slide the height adjustment
handle onto the rod by aligning
the at section and secure in
place using the screw that was
previously removed.
4 Ensure the blade height is wound
fully down and then turn the table
saw upside down on the oor.
2 Remove the screw from the
height / bevel rod and slide the
bevel adjustment dial onto the rod
ensuring the teeth on cogs align.
22.5°
15°
30°
45°
12
3
4
5
5
6
FITTING THE BLADE GUARD ATTACHING THE RUBBER FEET
TBS-254
IMPORTANT! THE BLADE GUARD MUST ALWAYS
BE LOWERED OVER THE WORK PIECE BEFORE
YOU BEGIN TO CUT.
2 Loosen the riving knife securing
bolt using the supplied spanner,
ensuring the bolt does not come
completely out as this bolt may be
dicult to ret.
2 Repeat the process for the other
three rubber feet.
4 Mount the blade guard to the top
of the riving knife using it’s nut
and bolt. Do not tighten the bolt
too far – the blade guard must be
able to move freely.
1 Flip the table saw upright onto it’s
feet, raise the blade to it’s highest
setting and remove the table insert
by loosening the 2 screws holding
it down.
1 Turn the table saw on its side and
press one of the supplied rubber
feet securely onto the corner of the
frame..
3 Insert the riving knife between the
mounting plate and the securing
bolt so that there is a 3-5mm gap
between the blade and the riving
knife. Tighten the securing bolt
using the supplied spanner.
5 Fit the table insert and secure with it’s 2
screws.
3 - 5mm

Produkt Specifikationer

Mærke: Ozito
Kategori: Sav
Model: TBS-254

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito TBS-254 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Sav Ozito Manualer

Ozito

Ozito TSB-0810 Manual

12 August 2025
Ozito

Ozito TSF-1211U Manual

9 August 2025
Ozito

Ozito SCMS-2125U Manual

9 August 2025
Ozito

Ozito CMS-1621U Manual

9 August 2025
Ozito

Ozito PXBCS-1830 Manual

24 December 2024
Ozito

Ozito TBS-254 Manual

8 Marts 2024
Ozito

Ozito PXCPRSK-218U Manual

4 Marts 2024
Ozito

Ozito OCS-018 Manual

3 Marts 2024
Ozito

Ozito SCMS-1621MS Manual

25 Februar 2024
Ozito

Ozito BSW-2581U Manual

13 Februar 2024

Sav Manualer

Nyeste Sav Manualer

Wolf Garten

Wolf Garten PS 20 eM Manual

27 September 2025
Yato

Yato YT-82811 Manual

27 September 2025
Poulan

Poulan P3516PR Manual

26 September 2025
Poulan

Poulan P4018AV Manual

26 September 2025
Poulan

Poulan PL1416 Manual

26 September 2025
Poulan

Poulan PL3816 Manual

25 September 2025
Poulan

Poulan P3314 Manual

25 September 2025
Poulan

Poulan Pro PRCS16i Manual

25 September 2025
Poulan

Poulan P4018AV BH Manual

25 September 2025
Poulan

Poulan Pro PR25PS Manual

25 September 2025