Panamax MD2-AV Manual

Panamax Ikke kategoriseret MD2-AV

Læs gratis den danske manual til Panamax MD2-AV (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 74 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 37.5 anmeldelser. Har du et spørgsmål om Panamax MD2-AV, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Cover can be flipped around 180

degrees to hide LEDs from front

straight-on view if desired.

Cover can be removed and painted to match

color of wall. Do not paint the sides, top or

bottom. Warranty will be voided.

Cover of MD2-AV can easily be removed

by pulling cover at the 2 side indents (1).

Unit can be securely screwed into wall

outlet faceplate using either hole (2)

indicated (screw is included).

1690 Corporate Circle, Petaluma, CA 94954 • 800-472-55555 • 707-283-5900 • Fax 707-283-5901 • www.panamax.com

INSTALLATION INSTRUCTIONS MD2-AV

Bottom view

of MD2-AV

Top view of product

DIN-OOOO8-A 6/11

CUSTOMER SUPPORT:

800-472-5555

OPTIONS FOR SECURITY MOUNTING & FRONT COVER FACEPLATE

FEATURES

LINES IN

FROM

MD2-AV

LEFT SIDE

OUTLET

GROUND

PLUG OUT

RIGHT

SIDE

OUTLET

GROUND

PLUG

DOWN

Side views of product

1. Turn off the equipment you are plugging into the MD2-AV.

2. Plug the surge protector into the wall outlet. A red "Line Fault" light indicates an

improperly wired outlet that must be checked by a qualified electrician.

3. If the blue "Power On Protection OK" light is on, plug your equipment into the

AC outlets on the surge protector.

The protection circuitry on the MD2-AV and MD2-AV MODULE only work

if the signal lines are connected properly and ground wire is bonded as

depicted in diagram below.

4. Connecting signal lines to the MD2-AV: The lines coming from the MD2-AV

MODULE plug into the “IN” jacks. Lines from the “OUT” jacks then connect to the

equipment being protected.

4.5 Connecting signal lines to the MD2-AV MODULE: The lines coming from the

MD2-AV plug into the “IN” jacks. Lines from the “OUT” jacks then connect to the

source equipment in the rack.

5. To mount module to rack, slide zip ties through slots on back. Wrap and tie

around leg on equipment rack.

6. Turn the connected equipment ON and

check for power and correct operation.

Panamax surge protectors and the connected equipment must be indoors in a dry location and in the same building. Do not install any

Panamax product near heat emitting appliances such as a radiator or heat register. Do not install this product where excessive

moisture is present; for example, near a bathtub, sink, pool, basement floor, fish tank, etc.

It is not uncommon for a building to be improperly grounded. In order to protect your equipment, and validate the warranty, Panamax

products must be plugged into a properly grounded 3-wire outlet. Additionally, building wiring and grounding must conform to

applicable NEC (USA) or CEC (Canada) codes for the Panamax warranty to be valid.

Do not use 2-prong adapters with this product. If an extension cord is required, use only Panamax #GEC1410. If at any time your

surge protector indicates a Line Fault, call your electrician to correct the building wiring.

POWER ON /

PROTECTION OK- (blue)

normally ON - indicates

that the power is on,

surge protector is

functioning properly,

and all connected

equipment is protected.

LINE FAULT INDICATOR-

(red) - If lit red, indicates

an improperly wired outlet.

AC outlets are turned 90 degrees from one

another to accommodate different style

plugs or transformers.

Properly Connecting Your Surge Protector

To completely protect your equipment from power surges, every wire leading into or out of the equipment you want to protect must be connected to the

appropriate Panamax surge protector. Damaging lightning and power surges can get into your system through any AC power or signal line (phone lines,

grounding wires, coax cables, modem cables, etc.) connected to your electrical equipment.

The $100,000 Connected Equipment Protection Policy is invalid if any wire leading into or out of the equipment is not properly connected to the

appropriate Panamax surge protector(s). The surge protector must also be plugged into a properly wired and grounded outlet. Please see the warranty

for details or contact the Panamax Customer Relations department with questions.

Overview

Make sure you have the right surge protector to protect your electronic equipment. Panamax makes protectors for almost every type of electronic

equipment. Surge protectors that may look identical from the outside can be very different on the inside. It is very important to use the surge protector

designed for your application. Two-outlet surge protectors are not designed for use with systems having more than two AC powered components.

Panamax offers a wide range of surge protectors designed for use with larger systems. If you have any questions about which product is best for your

applications, please see our web site www.panamax.com or contact Panamax Customer Relations at 800-472-5555 (7:30 a.m. – 4:30 p.m. PST).

Limited Lifetime Product

Warranty*

100,000

Limited Connected

Equipment Protection Policy*

MD2-AV

MD2-AV MODULE

GROUND WIRE CONNECTED TO

GROUND LUG ON BACK OF